Does anybody make slim grips for a CZ75b?


PDA






DrDremel
December 31, 2002, 12:09 PM
I have the factory plastic grips but they are still a little thick for my wife to reach the double action trigger. I would like to find some super thin synthetic grips to replace the ones I have. Anybody know where to find some?

If you enjoyed reading about "Does anybody make slim grips for a CZ75b?" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
45R
December 31, 2002, 01:45 PM
Try Hakan Grips

cratz2
December 31, 2002, 03:02 PM
If anyone does, Hakan will be your best bet. Beautiful grips but certainly pricey.

hansolo
December 31, 2002, 09:40 PM
FOR CHEAP you can try the HOGUE rubber wraparounds with fingergrooves; $15-20...I love the look of Hakan's but, for now, the HOGUE's are pretty slim.

Prodigalshooter
December 31, 2002, 10:05 PM
Hakan made the 1st pair I ordered extra slim for me, he's making a new pair (in burl:cool: ) also slimmer than standard. I think his grips are pretty reasonable, considering his price includes shipping across the POND!:D

MessedUpMike
December 31, 2002, 11:07 PM
I believe the CZ factory hard rubber grips are suppossed to be thinner than the plastic ones, cheaper than the Houges to.


Mike

railroader
December 31, 2002, 11:30 PM
I have uncle mike's which I think are quite slim. They are rubber copies of craig spegel grips. Mark

Lochaber
January 1, 2003, 02:25 AM
My CZ came with the god awfull plastic finger rest grips and I replaced them with a set of Houge warp arounds. Though comfy, I found that they made the grip a bit longer (front to back) for my taste, and I know have a set of the CZ factory rubber grips. They are quite thin and I find them very comfy. YMMV

Loch

Sven
January 1, 2003, 03:02 PM
Hakan's website:

http://www.imageseek.com/hakan

Hakan will make them to your specs and is a very nice guy, to boot. You can contact him directly at:

hakanpek@online.no

http://www.imageseek.com/grips/a.jpg

PS: Tell him Sven sent you. =)

bompa
January 1, 2003, 10:09 PM
I recently bought a set of CZ rubber grips and think that they are a bit thicker than either the plastic or checkered wood that can be ordered from CZ-USA.. I think the checkered wood are the thinnest of the factory grips..When Hakan gets his checkering
worked out I will have a set,for sure..

Zip06
January 1, 2003, 11:10 PM
My 75B came with terrible stock thumb grips. I ordered some replacements from CZ-USA for about $9.00 and like the new ones, they should have been stock grips.

tatters
January 1, 2003, 11:48 PM
I have Hakans as well, but not synthetic.

Great custom made grips, I feel a good value. Check out the CZ forum

PCRCCW
January 2, 2003, 10:24 AM
From the thickest to the thinnest you can find for the CZs....
The Oem Rubbers are the thickest
Then the Wood OEM CZ's
Then the plastics..OEM CZ's
Then Hakans being the thinnest....

Hogues vary from wood to rubber..the woods arent too bad.

Shoot well

Marcus
January 2, 2003, 10:59 PM
I have Hogue checkered cocobolo on my CZ-75B and Hakan`s first set of Xtreme (stippled panels with engraving) grips on my 10mm Witness. They`re both very thin. I measured the thickness of the grip on my CZ with the Hogue grips vs. a Springfield 1911 with factory wood stocks and the CZ is actually thinner! Both the Hogues and Hakans measure 1/10" thick measured straight across the frame. Total width for the CZ 1.15", 1.20" for the Witness (which is large frame). Marcus

If you enjoyed reading about "Does anybody make slim grips for a CZ75b?" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!