The Official Holster cross-compatibilty thread.


May 27, 2005, 01:19 PM
I got this idea while going through my collection of holsters for guns that I no longer own.
What fits what? We all know that some holsters will work quite well for guns that they weren't designed for. From my personal collection this is what I have found so far....

Just about any holster that was designed for a Glock 20/21 will fit all other Glocks. (leather AND plastic) Some might be loose, some fit perfectly.

A Don Hume 715 IWB for a Glock 29/30 fits quite a few other pistols like a SW 3913

Milt Sparks 55BN made for a Sig 2340 fits a SW 908/3913 like it was made for it.

Holsters designed for an Officers size 1911 will hold a PPK, Sig230/232, or similar very very well.

Safariland open top mag holders for a SW59 hold single stack 45acp mags perfectly.

What's in your collection that fits multiple firearms? Inquiring minds want to know. :)

If you enjoyed reading about "The Official Holster cross-compatibilty thread." here in archive, you'll LOVE our community. Come join today for the full version!
May 27, 2005, 02:36 PM
Most holsters that will fit a Sig 239 work just as well for my S&W 3914.

May 27, 2005, 04:50 PM
Full size Beretta 92 rigs can fit CZ 75s. My Galco paddle for a Sig P229 fits my CZ PO1 quite well....

May 27, 2005, 05:22 PM
This is good stuff. Keep it coming. I am taking notes! :D

May 27, 2005, 05:55 PM
Most holsters designed for a Glock 26 fit the Taurus PT-111 very well.

May 27, 2005, 06:25 PM
A g17 slide will hold a Walther p99 (like it was made for it). A threat solutions UCR for a Glock 17, will hold a G 20, and also a Wather p99.

A ruger slide holster will hold a 9mm or 40 USP.

Andrew Wyatt
May 27, 2005, 06:44 PM
A summer special for a Govt. Model will fit a BHP.

A blade tech outside the pants kydex holster for a 1911 will fit a BHP.

A pattern 44 Flap holster for a BHP will fit a 1911, a commander, a .40 BHP, and a CZ-40.

lee n. field
May 27, 2005, 07:30 PM
This needs to be in chart or database form.

May 27, 2005, 08:00 PM
BHP into a 1911 holster as stated above.

May 27, 2005, 08:27 PM
This needs to be in chart or database form.

Hook us up. ;)

Headless Thompson Gunner
May 27, 2005, 08:55 PM
Can anyone tell me whether the Kahr guns fit snugly in a 1911 holster? Slide length is obviosly a problem, but how about otherwise?

May 28, 2005, 05:04 AM
My 3" Kimber fits into the Kahr K9 holster like it was made for it. A perfect fit. :)

May 28, 2005, 07:35 AM
Ive never tried it but i read that the Bersa Thunder (.380) fits perfectly into holsters made for 3" 1911s. Someone on the bersa forum tried this with a really nice high end holster and it worked quite well.

May 29, 2005, 12:12 AM
Kahr K9 does fit 1911 holsters. Not sure about safety straps, but they vary with hammer and holster manufacturer anyway.

Bianch IWB Pistol Pocket for Walther PPK is perfect for Colt Challenger, including strap.

Bianchi Pistol Pocket for Colt Detective Special perfect for 3" S&W Model 36-6 (full lug), and presumably for the similar Model 60 3" full lug.

Just got a beautiful Bianchi 6" #5BHL for S&W K-frame that's not all that tight on a Model 10 with standard hammer, but fits my Colt 6" HB Official Police just fine.

May 29, 2005, 12:20 AM
My Don Hume JIT holster for my XD fits my glock and HK usp 45..

Also my IWB don hume fits them all too

chris in va
May 29, 2005, 01:09 AM
Interesting about the CZ75. I'll have to look at those Beretta holsters because CZ ones are about impossible to find in the stores.

May 29, 2005, 04:57 PM
Interesting careful when crossing over leather.....if its got good retention then cool. Id hate to have your gun end up on a floor somewhere...
CZ holsters are getting more common, most makers do make them now.
Shoot well........

May 30, 2005, 06:09 PM
Of course J-frame S&W holsters usually work fine for Taurus 85, 605 and similar and K-frame/L-frame holsters usually work with medium framed Taurus revolvers.

I have heard (but haven't tried it) that holsters for the compact (or sub-compact, not sure) Springfield XD .40 work great on a Taurus PT140 Millenium Pro.

May 30, 2005, 07:13 PM
But my S&W L frame won't fit into my K frame holster. Cylinder is to fat. :mad:

May 31, 2005, 01:45 AM
My El Paso Saddlery holster for a Glock 30 fits my Bersa FireStorm .45 nicely.

Also know the Vega holsters for the Glock 26 & 27 will work well too.

If anyone knows what leather holster will fit a Weirauch (EAA) Windicator snub-nose, it would be appreciated.


May 31, 2005, 08:39 AM
desantis k-frame holsters....Ruger 6's,Rossi 461,sp101(but it's a little loose)

June 4, 2005, 12:09 AM
Ruger P345 with rail fits into Galco or Bianchi HK USP compact; thumb strap is not very snug though, if equipped.
P345 also fits well into Galco pancakes for Glock 20, 21 even with fairly tight thumbstrap. I think it is a better fit than HK USP.
Then of course you'd go for it if you are in a hurry because costwise it is basically the same as to get a High Noon specifically designed for P345.

June 5, 2005, 06:59 AM
Two more I just found. Sig P229 fits nicely in Glock 29/30 leather AND Sig 2340 Leather. :)

June 5, 2005, 08:26 AM
Galco Silhouette for the Sig 228/229 fits the Glock 19. The thumb-break even works. I would guess that the 23, 26, 27, 22, 17, etc. would also work. The glock sits differently in the holster but is still secure.

June 5, 2005, 10:59 AM
I carry my CZ P-01 in a holster made for a HK USP Compact 9/.40

June 5, 2005, 01:51 PM
BHP into a 1911 holster as stated above. :scrutiny: :uhoh:

I have always found the BHP doesn't work in a 1911 holster worth a dang, no matter who made it.


June 6, 2005, 12:53 AM
I have always found the BHP doesn't work in a 1911 holster worth a dang, no matter who made it. Really? I just considered a puchase of a BHP .40 about 6 months ago. Went to Gander Mountain and tried a BHP in a Bianchi Carry-Lok. Fit was perfect!


W Turner
June 6, 2005, 01:57 PM
CZ P01 and 75B works great in a FIST belt slide made for a Glock 10mm/.45

SW j-frame in a Don Hume Belt Slide for a Glock 10mm/.45

CZ 75B worked really well in a Uncle Mike's kydex belt holster for a Glock 17 and in the two other belt slides mentioned above

Other than barrel length, a CZ 75B also fit perfectly into a pancake holster for a Beretta 92.

Glock 30 fit great in a Safariland 3-slot pancake for a HK USP Compact .45 after I had the thumb break removed

Ruger GP-100 4" works great in a Don Hume Askins-style belt holster for a SW N-frame


June 6, 2005, 02:07 PM
I have an Uncle Mike's cheap IWB holster for a Ruger SP101 3" that also fits a GLOCK 26/27 and 19/23.

June 6, 2005, 10:42 PM
FYI, a Ruger Redhawk with 5-1/2" barrel fits perfectly in a surplus leather flap holster originally made for a Webley MkVI with 6" barrel. I think a 6" S&W N-frame or Taurus equivalent would also fit in this holster.

Also, when I was working in a gun shop I would stock Don Hume belt slides(JIT,H710 "Agent") for the Glock 29/30, as I found that the HK USP in 9mm/.40S&W would fit perfectly in those holsters. Likewise, the Kahr, KelTec P11, and S&W SW9 can share holsters.

June 7, 2005, 09:32 AM

A Bianchi size 13, for Ruger P90, will accept the Ruger SP101 2.25" barrel, .357. The retaining strap works, with adjustment, of course. However, it's not perfect, but certainly acceptable. The trigger is covered & with the strap, retention is not a problem. Don't think retention would be a problem even without the strap due to the SP101's cylinder being wider than the frame of the P90. Ease of holstering is marginal, but not completly out of line.


June 7, 2005, 10:54 AM
My Galco paddle for a Sig P229 fits my CZ PO1 quite well....

My Uncle Mikes Old World Pancake holster originally bought for my Sig P228, actually fits my CZ-75B, although the slide sticks out of the bottom just a little. And it has a thumb-break, so I could carry the CZ cocked & locked if I wanted to.

June 7, 2005, 09:40 PM
Baby Eagles fit Glock 17 holster well, an Arcus fits in them also.

June 12, 2005, 10:37 AM
I carry my Kel Tec p-11 in a Don Hume belt slide made for a Beretta 92 which as stated also fits my CZs.

Ky Larry
June 12, 2005, 03:05 PM
My CZ PCR fits an Aker Leather model # 168-A belt slide holster made for a SIG P225.

June 12, 2005, 06:08 PM
Discovered yesterday that my Sig P229 and Sig P239 can share leather. :D

June 13, 2005, 12:31 AM
The Fist #1 clip holster for the Beretta 92FS also fits my Walther P5.

June 13, 2005, 08:32 PM
I had a FIST belt slide (forget the exact model) made for an XD .40 that I had that also fit a Sig P220 and P226.

July 16, 2005, 08:33 PM
I just discovered that my Galco Yaqui slide for my SigP229 fits my SW 1076 PERFECTLY. :eek:

July 30, 2005, 08:33 PM
Ruger SP101s fit in Colt Detective holsters.

July 30, 2005, 08:55 PM
My Don Hume JIT belt slide not only fits my P11 but also, P08 Luger, MKII Ruger, 1911 all perfectly!

August 18, 2005, 08:30 PM
Just discovered that my Sig 229 yaqui slide fits the Ruger P345 too. THis holster fits a lot of different guns! :cool:

August 19, 2005, 01:07 PM
Galco 1911 G-Slide fits commander, and BHP just fine, Ditto for Dillon's CLS (Cactus Leaue Slide). That good old US GI holster designed for a 1911A1 will also fit your commader, BHP or strangely, a Luger.

Colt Magnum Carry/Detective Special will fit well in a holster designed for a Ruger SP-101. (Galco Hi-Ride, Bianchi Accumold)

And, with a little gumption, a holster designed for a six inch Ruger Gp-100 will fit a Colt New Service IF it doesn't gover the trigger guard (Bianchi #5) Colt's New Service is a hard gun to find leather for, some Python holsters fit, some don't.

Any holster that fits a 7.5 inch Colt SAA or Ruger Vaquero will fit a Colt 1851 Navy or 1860 Army.

The FEG Pa-63 is bigger than a PPK/s... it may or may not fit holsters designed for the Walther.

August 19, 2005, 06:31 PM
My K9 fit in my 1911 holsters to different degrees of success. The Milt Sparks was good the Rafter S bad with the Alessi in the middle.

Tom Servo
August 25, 2005, 04:44 PM
I have a Sig P225 and P245, but I just order holsters for the P245 because the P225 fits perfectly. Slide's just a bit shorter.

My Wild Bill's paddle for my 75B is also a perfect fit for my 1911 Commander.

August 25, 2005, 08:50 PM
My Don Hume JIT holster for my Sig 2340 will also fit my XD 9.

My one Galco FLETCH will also fit my 2340 and XD, and my Ruger 345.

August 28, 2005, 09:01 AM
Highnoon IWB purchased for Styer M9 and I use it for my S&W 457 I had to do a small amount of work for the safety to cruise in and out easily.

August 28, 2005, 10:41 AM

This is a great thread and thanks to the starter. This is the kind of thing that I read THR for. Where else are you going to get this kind of info? Nowhere, thats where.

If this was in table form it would be great. Anyone good with that kind of thing? We could link to it if needed and have a great resource.

I guess I'll add my two cents. I had a Glock 17 holster that fit my Ruger P-95. I guess it would work in a pinch but it was not great.

August 28, 2005, 10:45 AM
Fits my FM hipower Detective 4" perfectly. My Galco Belt slides for 1911 fit 1911s, Makarovs, Hipowers, and Kahr 9mms. The Kahr holsters with thumb break fit 1911s with the hammer down, or hammer back with a standard sized safety. Extended or Ambi-safetys come off in the holster with the thumb break.
My Miami Classic for Kahr k-9 fits the micro and compact 1911s perfectly. (The mags don't fit in the offside pouch, but a new mag carrier is cheaper than a whole new rig.)

August 28, 2005, 11:12 AM
Sold the XD and kept the JIT because it fits my:

Sig 228 9mm
USP Compact .45
Beretta Cougar 8000 9mm

August 29, 2005, 01:49 AM
I tote my Steyr S40 and M40 and now a Walther P99 (2004 model) in a Galco Concealable holster made for the HK USP Compact....both fit like a glove.

Here's a photo of my M40 in the holster.

September 13, 2005, 08:23 PM
Just tried my Sig P239 357sig in a Galco UDC horsehide IWB made for a Glock 26/27/33 and it works perfectly.

January 6, 2006, 03:59 PM
I just discovered that my PT145 fits perfectly in a Galco Ankle Glove made for a Glock 27.

January 6, 2006, 06:07 PM
As one who always carried the oddball pistol I have several to add.

Astra A75 fits great in a Galco SOB226 and a Bianchi #11 Kydex high ride.

Polish P-64 fits great in a Ross Leather Sig230 IWB and probably would fit in any holster made for a Walther PP.

January 7, 2006, 12:26 PM

My Sig P245 fits nicely in all my Milt Sparks P220 holsters.

The 220 will almost fit in my 245 Sparks VM-II, but since the barrel length prevents the trigger guard from fully seating, I would not consider this a secure method of carry.


January 7, 2006, 01:13 PM
My P85 and P90 both fit my Sparks Summer Special, of course. Neat thing, I bought this Russian military flap holster for a makarov even though I don't have a Mak. I was making an order and it was cheap, so I just got it just because. It's cloth lined, has a magazine pouch on it, and my .38 Rossi M68 three inch or my M511 .22 fits it. I like flap holsters afield, protects the gun. It's a compact belt holster and the mag pouch will fit a full bianchi .38 speed strip. :D

January 7, 2006, 10:09 PM
I have a Ted Blocker DA3 built for a Browning Hi-Power that also works well with my 1911.

January 8, 2006, 10:28 AM
Galco Fletch for XD also takes my Sig P220 perfectly.

January 8, 2006, 10:32 AM
My old horsehide NSA holster for the 5" 1911 also fits my Browning High Power. In fact, Galco's holster fit guide lists the same holster code number for each.

January 8, 2006, 11:05 AM
Ross leather for Glock 19 seems to fit my Po1 like a glove.

Beetle Bailey
January 12, 2006, 03:32 AM
Fobus roto-paddle holster for Beretta 92/96 fits my CZ75B Tactical. I used this set-up when I did a Bianchi Cup practice and had no problems.

January 12, 2006, 03:49 AM
my S&W 9VE fits perfectly in a Glock 21 holster.

January 12, 2006, 09:34 AM
Discovered yesterday that my Sig P229 and Sig P239 can share leather. :D

How consistent is this? I'm searching for an inexpensive P239 (357 Sig) holster at the moment. What I WANT is a Milt Sparks VMII. Just can't afford at the moment. :(

January 12, 2006, 10:16 AM
How consistent is this? I'm searching for an inexpensive P239 (357 Sig) holster at the moment. What I WANT is a Milt Sparks VMII. Just can't afford at the moment. :(

I should have been more specific. The 239 will fit in some holsters designed for the 229 since the 229 is a bit larger. The 229 will not fit in leather made for a 239.

Check out the classified section over at
I've seen a few VMII's for 239's come up for sale.

January 12, 2006, 06:03 PM
My P228 fits perfectly in the Don Hume H715M that I have for my Glock 19.

January 12, 2006, 07:33 PM
The Fist #1 leather holster I bought for my SA XD-9 has always been a difficult draw with the XD-9 even after break in. It works perfectly with my CZ PCR.

January 13, 2006, 09:41 AM
I should have been more specific. The 239 will fit in some holsters designed for the 229 since the 229 is a bit larger. The 229 will not fit in leather made for a 239.

Check out the classified section over at
I've seen a few VMII's for 239's come up for sale.

Thanks for the clarification! I keep an eye out on SigForum, but I never seem to be in time. :p

February 1, 2006, 04:02 AM
Maybe this is the wrong place/thread to ask but does anyone know if any of the Blackhawk SERPA ( holsters are compatible with a Ruger P345? Thanks.

February 1, 2006, 05:31 AM
I have a Don Hume thumb-break belt-slide leather holster for the USP 9/.40 full-size that will also fit the .45f, however, the thumb snap will not fasten unless you carry cocked & locked. It will not carry my .40 compact.

My Safariland 6240 duty holster fits my USP .45f, Beretta 92FS, and Sig P226, although the tension screw must be adjusted.

My Galco thumb-break belt-slide leather holster for a the Glock 17/22 fits my P226 well enough for carry.

I have a Bianchi M12 military flap holster that fits just about any 4"-5" barreled auto including S&W 3rd-gens, Berettas, Sigs, 1911s, and Glocks, but will not work with the USP as the trigger guard is too large. The matching magazine pouch will fit everything as well except for my USP .45f magazines. Note that the plastic divider can be removed to accomodate 1911, Glock or USP 9/.40 mags.

February 1, 2006, 10:49 AM
My Bianchi Accumold Size 15A fits both my Sig 239 and my Glock 21. Talk about opposite ends of the spectrum!

February 2, 2006, 12:02 AM
4" XD's will fit SIG 226 (and similar lenght models) holsters.

April 4, 2006, 02:11 PM
Galco WB404 suede IWB holsters for the Colt Pony (IIRC) will fit the Kel-Tec P-3AT like it's made for 'em.

Edit: Probably the P32 as well.

April 4, 2006, 02:48 PM
My info above is incorrect. It should be the other way around. Sig 226 will fit XD's. I tied to edit but it I can't. I apologize if I had misled someone.

April 6, 2006, 09:35 PM
Kramer Horsehide IWB for Sig 220 works perfectely for all sig P series pistols. If you look a the stats, there is less than a inch difference in height and length between a P-220 and a P-239, and less than 2 oz. in weight. Hi cap 9mms are a tight fit at first. I am not sure that I would try this with a regular belt holster. However, the IWB works just fine because of the extra tension provided by the belt and waistband of your pants.

S&W 908/3913 fit very well in a Rafter S made for glock 19.

Janos Dracwlya
April 8, 2006, 11:02 PM
A Fobus holster for a Sig Pro will also fit a Sig 226 and 225. (I needed a holster for a Sig P-226 quickly and cheaply and found a Sig Pro holster in a bargain bin that was a great fit)

I have a holster for a S&W Model 10 with 4 inch barrel that also fits my Ruger Service Six with 4 inch barrel perfectly. I don't recall the brand - it was one of those leather, multi-position holsters that Sportsmans Guide sells.

November 22, 2007, 06:31 PM
Old thread, but I found that a Fist leather #2 for a Glock 26 (open muzzle end) fits my CZ-P01 better than the glock 26 it is designed for! The muzzle protrudes about .5", so the same holster for a G19 would probably fit perfectly!

November 22, 2007, 09:44 PM
^^agreed, but glad you found it-was emailing a couple of folks trying to find something to fit my charter arms mag pug and firestar .40
prompted me to do some more searching and the Galco SOB218B for 1911 types w/3.5 in barrels fits the firestar...

November 23, 2007, 01:40 PM
My Don Hume JIT. slide holster # 26 made fo my Beretta 96 / 92 FS. is a perfict fit for my S&W 1006 with the round trigger guard. Also my Safariland #4,340,437 S&W-L made for my S&W 686 with a 4in. bbl. will also fit my COLT Python and my RUGER GP-100. This is a duty type holster made to fit a 2 1/2 in duty belt, it has 2 allen head set screws to snug it to the belt. There is another # above the model # . It is 200 seperated by the antelope's head then A94.:)

November 23, 2007, 02:27 PM
Has anyone found a holster that fits a Colt pocket Hammerless or a CZ52?

November 23, 2007, 02:44 PM
Sig P232 fits perfectly in the IWB Bianchi holster I have that was originally made for a Walther PPK.

Galco OWB for a Ruger P90 will hold a Sig P239. Thumb break isn't snug, and there is an extra 3/4" of unused leather at the bottom, but it works fine for IDPA. In fact I used the Galco as a pattern to make a new holster specifically for the 239. Haven't made the holster yet, but I have the pattern done.

November 23, 2007, 08:40 PM
Old thread, but I found that a Fist leather #2 for a Glock 26 (open muzzle end) fits my CZ-P01 better than the glock 26 it is designed for! The muzzle protrudes about .5", so the same holster for a G19 would probably fit perfectly!

Just found out something similar - that a Safariland Model 27 IWB holster made for the the Glock 17/22/31 will fit a CZ SP-01 perfectly!

The Lone Haranguer
November 23, 2007, 09:43 PM
I just got a CZ75D Compact and found that it fits well in a SIG P228 holster. :) This is a Dillon Leather by Mitch Rosen, very rigid and detail molded to the SIG, so I have confidence that other "off the rack" holsters will also fit. It also fits passably into a Don Hume IWB for a Glock 19, but not into a more rigid Galco Royal Guard for the same gun. So gun/holster fit is very dependent on how rigidly/tightly fitted a holster is to a given handgun.

November 23, 2007, 10:47 PM
I have a Galco paddle holster for a Glock 17. My 1911 fits in it like a glove.

November 24, 2007, 10:54 PM
A DeSantis Nemesis Pocket Holster for a Kahr PM 9 works great for a S&W J Frame Centennial.

November 25, 2007, 03:35 AM
In reference to the earlier post about L-frame cylinders not fitting K-frame holsters, it's not so much the cylinder as the depth of the frame. Ruger Security/Service/Speed Six and GP100, the S&W L-frames, and Colt Pythons are about the same size, and can usually share holsters. Some K-frame holsters can stretch to fit these sixguns, such as my El Paso Saddlery Threepersons rig, but by no means all of them.

November 25, 2007, 07:56 AM
Just found out this one to my delight:A CA Bulldog fits in a Desantis thumbreak for an SP101...I was surprised and happy,more money for ammo.

Mad Magyar
November 25, 2007, 09:11 AM
Hell, you miss the excitement & disappointment of going through your "box full of holsters!" :)

November 27, 2007, 03:10 AM
Great thread!

My wife does Web design stuff and she says she'll put the info in this thread into a Wiki-type database that is user update-able if I'll sort out the interchangeability posts that are here so far...
I've got nothing else to do besides shoot, load, feed horses, mend fences and go to work... So what the *. I'll print it all out and get started. I don't have enough to do...

My contribution is:
A Kahr K40 will fit into most Makarov holsters and vice versa. I use an Old World 23017 belt slide for both. It took a little effort to get the thumb break to fit over the Maks, but now it works very well. The Kahr also drops nicely into the full-flap Makarov milsurp holster, but the mag is a tight fit. The cheap EG Mak shoulder holsters also handle the K40 securely as well.
The Sig P220 and the Tanfoglio Witness .45 (and by way of speculation the CZ75) fit almost all non-molded holsters interchangeably, but I know they fit the El Paso Leather (a South African company - don't ask me how I ended up with a South African holster) molded leather holster made for the USP 40.
A bit off topic is that my Milt Sparks mag holders for the Glock 20 fit Tanfoglio and CZ double stack .40 and .45 mags.

November 29, 2007, 08:59 PM
In reference to my post #78, I just checked and my Don Hume H721 #26-5" O.W.B with thumb brake made for my Beretta 96 / 92 FS. is also a perfict fit for my S&W 1006 with the round trigger guard.

November 29, 2007, 10:00 PM
Most holsters for SIG 229 work great for Taurus Mil-Pro pistols.
Uncle Mikes "Super Belt Slide" Size 20 fits a CZ-75, CZ-52, and 1911 style guns

EDIT: And I'm now the owner of a Galco retention holster intended for a 3" 1911 style pistol that fits my Bersa Thunder 380 Concealed Carry model just dandy (so apparently that style of leather holster will work for BOTH the Thunder 380 and the Thunder 380 Concealed Carry)

March 10, 2008, 10:38 PM
This thread hasn't seen daylight in a while. Anyone have any new info?
How's that Wiki database coming along?

May 22, 2008, 08:30 AM

August 14, 2008, 02:49 PM
Any level II or III rigs suitable for open carry that fit the CZ-75?

September 2, 2008, 11:15 AM
Just found that the Bianchi AccuMold Belt Slide Size 15A I bought for a long departed Sig 239 fits my new Walther P99 better than it ever fit the Sig.

September 8, 2008, 12:26 AM
any holster that fits the Taurus 24/7 Pro series seems to fit the Millenium Pro series as well.

My EDC is a Galco Matrix M7X446 kydex beltslide. Made for a Springfield XD, but fits my PT145 like it was made specifically for it. I've had good luck with fitting most XD holsters with this weapon in fact, except the one I really want- a Serpa CQC Level 2.

September 19, 2008, 12:59 PM
Glock 22 fits well in a CompTac MTAC IWB for Springfield XD45

September 21, 2008, 01:31 PM
Kel-Tec P32/P3AT fit into the Galco DC404 even better than the WB404, since the WB404's thumb-break loosens up over time. That said, it's also thicker than the WB404 and lacks any thumb break, but you get a metal rigidity bit around the top for re-holstering.

October 2, 2008, 02:12 PM
Update, If you have a CZ-75b in .40 S&W you can use the FOBUS holster for a Beretta 92 (it's the same holster sold for both).

If you have a CZ-75b in 9mm you have to get the FOBUS specifically for that pistol or it'll shuck around and not "lock in".

Annoyingly there is no lefty 9mm holster yet (arrrrggghhh!)

Tagua leather retention holsters for the Glock 17 also work for the CZ-75b (all full size ones) though the fit is not perfect the retention strap will keep it from falling out.

Wayne D
October 30, 2008, 02:54 PM
My S&W 4566 with the square trigger guard fits in a Price Western Leather pancake holster for a Sig 226.

November 5, 2008, 04:03 PM
my galco ankle holster and milt sparks VM 2 for my glock 26 fit my new Walther 9mm PPS perfectly

November 5, 2008, 06:09 PM
I didn't check the whole thread, so I hope I'm not duplicating something previously posted, but I just started using my Fist IWB holster made for the CZ-83 with my Llama IIIA. Works great, when its inside the pants, just a wee bit loose otherwise. Not too much of a problem though, I'm happy with it. Can't find a holster for the IIIA anyhow, so I guess it will have to do.


November 9, 2009, 08:05 PM
Will a bersa thunder .380 fit in a Don Hume JIT slide holster for a makarov 9mm?

December 28, 2011, 04:30 AM
Hi all, this is my first post. im looking for something that will fit my s/w model 13 6inch, like a fobus type of holster. i would like it in a cross draw setup as a backup to my glock 22. (i work an armored car detail) i also have a model 60 i ground down the hammer on it , and the holsters i have seen all seem to use the hammer with the thmb break strap to secure the weapon. any ideas? any one last thig, i have a cz83, and again, i really like the fobus type holsters but i also want to get a mag pouch single or dual for it. any suggestions? this is a great thread and hasbeen really helpful with some of my other weapons! Thanks in advance!

January 13, 2012, 05:23 PM
DeSantis Nemesis pocket holster for a S&W J Frame works nicely with a Kahr PM9 or equivalent.

Friendly, Don't Fire!
January 13, 2012, 05:28 PM
My Desantis Gunhide Ankle Holster, with garter, works for both my LCP .380 and my 642 .38 Special! The .38 is a tad tight, but it definitely will not come out by accident and the entire trigger guard is covered!

The snap straps that hold the gun in the holster are completely adjustible as they are all secured with velcro.

February 2, 2016, 04:01 PM
At the risk of reviving and old one....Walther P99 galco fletch will also fit Sig P226.

February 3, 2016, 08:01 AM
Most handguns cost somewhere from $500 to $1,000 plus. If you can afford a new gun, spend the extra $100 and get a holster that fits your gun.

March 31, 2016, 05:03 PM
Anyone know a good holster for a Bersa Thunder 9 Pro HC / XT. I know the Fobus paddle holster for the sig p239 works but was looking for something that has a retention clip or something similar. For example, does anyone know if the SigTac Roto Retention Paddle Holster for SIG P239 ( works with these guns? No soft holsters please. Thanks in advance for any help!

March 31, 2016, 09:01 PM
Bersa Thunder 9 Pro HC / XT

I'm not familiar with the Bersa line-up, which one?

...looking for something that has a retention clip or something similar. For example, does anyone know if the SigTac Roto Retention Paddle Holster for SIG P239 works with these guns? No soft holsters please. Thanks in advance for any help!
What is the planned use for the holster? Does that mean you want a kydex holster and leather is not to be considered? Do you need a paddle? Does it have to have active retention or just something more than gravity?

April 4, 2016, 12:27 PM
This is the gun I have (

Yes, Kydex is preferred. It will be for open carrying. Active retention if possible. I want the extra step for anyone trying to grab it. Paddle is more of a nice to have.

I have found that XD9 kydex holsters sometimes fit it so I am gonna try this one (

I will let you know if it works. But please continue to post any suggestions. Thanks!

If you enjoyed reading about "The Official Holster cross-compatibilty thread." here in archive, you'll LOVE our community. Come join today for the full version!