How is the slide stop spring retained on Browning Medalist/Challenger?


PDA






1KPerDay
November 19, 2006, 01:17 PM
I finally tracked down the proper (I presume) slide stop spring for my Challenger, but can't figure it out and I don't want the spring to go flying across the room. The rear of the slide stop has a notch that I presume one end of the spring rides in... anyone here know which way the spring goes? Does the curved center of the spring wrap around the post of the slide stop latch or something?

If anyone has a Medalist and wouldn't mind posting a pic of the area or simply taking a look at their slide stop and letting me know which way the spring is oriented that would be great!

Thanks.:cool:

If you enjoyed reading about "How is the slide stop spring retained on Browning Medalist/Challenger?" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
1KPerDay
November 20, 2006, 11:56 AM
Bump...

jaybar
November 20, 2006, 02:24 PM
Does this help ???http://www.stevespages.com/ipb-browning-medalist.html

1KPerDay
November 20, 2006, 03:52 PM
It may... I looked at exploded diagrams on the web but that one looks different than the others I saw. The spring looks a bit different too. The one I got is a full "U" with a curvy bit on one end. I already bought an incorrect one from the Buckmark as someone on the parts site said the springs were interchangeable (they aren't).

Dang it...


thanks for the help. I know there are some medalist/challenger owners here, so hopefully somebody will be so kind as to unscrew the grip and take a good look for me.:cool:

Jim K
November 20, 2006, 10:11 PM
IIRC, the top part of that "S" curve fits into the groove in the end of the hammer pin, and the straight part bears down on the little projection on the inside of the slide stop. But I am confused by what you say about the "U" shape, which sounds more like a Buckmark.

Just remember the idea is to keep the slide stop down until the mag follower pushes it up. When you get the spring so it does that, you probably have it in right.

Jim

1KPerDay
November 21, 2006, 12:53 PM
Thanks... that might help. I'll take another look. Maybe I'm remembering incorrectly.

The "V-joint" of the spring doesn't wrap around a pin or anything, does it? It's just basically held in by tension, correct?

1KPerDay
September 19, 2009, 12:05 AM
Bump... I finally tracked down the right part I believe... anyone know a source for dis/reassembly instructions for a browning challenger? Please help... this pistol has not been working correctly for 20 years.

1KPerDay
September 20, 2009, 12:10 AM
by disassembly instructions I mean not an exploded diagram. or at least some idea of what order the parts should be removed/installed.

thanks

Bailey Boat
September 20, 2009, 10:00 AM
You might have better luck at rimfirecentral.com a site dedicated to all things rimfire...

1KPerDay
September 20, 2009, 12:32 PM
I'll try... My few pleas for help over there have gone unanswered. I'll try it though, thanks

1KPerDay
September 22, 2009, 12:35 AM
Well I got it back together... I'm posting in case someone in the future happens upon this thread with a similar problem to mine. Thanks to all.

After a very lengthy and expensive search I finally located a slide stop spring for my Browning Challenger (it was lost when I was a teenager and the pistol hasn't worked properly since).

Thanks to you guys and the rimfirecentral.com folks I had a general idea of where the spring went but it took a bit of trying to figure it out. The smaller loop clips into a groove at the end of the hammer pin, and the lower loop has to sort of be squeezed into a space that seems too small at first, but which gives it the necessary tension to hold the slide stop down against the force of recoil until it's overcome by the stronger magazine spring as the magazine empties.

Note: to get the safety click plate off, you move the safety lever down past the "off" position and that allows the click plate to be lifted up off the hammer pin.

I also replaced the front sight pin which was also lost many years ago. Feels good!
Wrong
http://i12.photobucket.com/albums/a206/1KPerDay/Guns/93dd6be7.jpg

Wrong
http://i12.photobucket.com/albums/a206/1KPerDay/Guns/00078ba6.jpg

Wrong
http://i12.photobucket.com/albums/a206/1KPerDay/Guns/8e7d3f7d.jpg

Correct
http://i12.photobucket.com/albums/a206/1KPerDay/Guns/19beffd5.jpg

Safety plate back on
http://i12.photobucket.com/albums/a206/1KPerDay/Guns/af470e55.jpg
http://i12.photobucket.com/albums/a206/1KPerDay/Guns/eec1566f.jpg
http://i12.photobucket.com/albums/a206/1KPerDay/Guns/95bf19bc.jpg


Video:

http://s12.photobucket.com/albums/a206/1KP...nt=6a8760cb.flv (http://s12.photobucket.com/albums/a206/1KPerDay/Guns/?action=view&current=6a8760cb.flv)

If you enjoyed reading about "How is the slide stop spring retained on Browning Medalist/Challenger?" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!