Revolver caliber suggestions


PDA






treebeard
December 27, 2006, 09:31 AM
Looking for suggestions on a caliber for a new revolver. I figured I do so much reloading that it would be time for another revolver. Does anyone shoot a .45ACP revolver? I don't want a Ruger because I can't stand their triggers. I have an "extra" 1911 that just sits in my safe so I want to trade it in. Thanks for any suggestions.

If you enjoyed reading about "Revolver caliber suggestions" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
lentuk
December 27, 2006, 09:43 AM
I have a Smith & Wesson 625-3 that is a .45 ACP, (model 625 stainless, 25 blue). It uses moon clips witch to me are much easier to use for fast reloads than any other speed loaders. This is my "nightstand" gun.
.45 ACP revolvers have been around since 1917 so you should not have a problem finding one.

MCgunner
December 27, 2006, 09:56 AM
If you reload, you NEED a .45 Colt...;) Of course, the Ruger Blackhawk can take full advantage of the caliber, short of a Freedom Arms anyway. Or, you could get a S&W Mountain gun in .45 Colt. Be a good outdoor carry. The little Taurus would be good for carry, but I'd rather have a bigger, more capable gun in this caliber to take full advantage of the power levels it can produce.

Or, how's about a .41 magnum. If I go for a new caliber, it's probably going to be .41 magnum. I've always had an infatuation with that one. I don't have a .40 or a 10mm, but I'm more of a revolver kinda guy.

Someone posted a pic of a S&W titanium airlite in .45 ACP. I bet that would be an awesome carry piece.

treebeard
December 27, 2006, 10:20 AM
Glad to see other people out there have some good suggestions. :D :D

Brian Williams
December 27, 2006, 10:32 AM
If you reload and do 45 ACP, get a good S&W 625 in 45ACP and reload some good ole foot stompers, the ACP can be loaded with some powders that in either a Ruger convertable or a good solid S&W 625 will breath some hellfire and brimstone. They are not in the 44 mag category but they can let you know you touched off a stout load.

treebeard
December 27, 2006, 10:47 AM
There are several 625-8's in 95-98% where I am going today. I may be bringing one home. :D :D

wundudnee
December 27, 2006, 01:34 PM
I agree with the S&W .45ACP. I have a Pre 26 and it just feels right when you shoot it. Not only can you load it heavy, .45 stuff seems to come on sale pretty often. I also have the high cost 10mm and .41 and don't reload yet. They're fun to shoot, but EXPENSIVE. Get the .45 or a .357 that you can plink with .38 specials.

azredhawk44
December 27, 2006, 02:01 PM
Looking for suggestions on a caliber for a new revolver. I figured I do so much reloading that it would be time for another revolver. Does anyone shoot a .45ACP revolver? I don't want a Ruger because I can't stand their triggers. I have an "extra" 1911 that just sits in my safe so I want to trade it in. Thanks for any suggestions.


A reloader's revolver, that isn't a Ruger...

Smith 625 sounds really good. If moonclips start to bug you, get some 45 autorim brass. They have a stronger base, too, so they can be loaded a skosh hotter than ACP brass.

highlander 5
December 27, 2006, 02:02 PM
I have a 625 I love it shoots better than i can and the added bonus of not chasing brass all over hell and earth.Rimz full moon clips are ok for plinking but the steel are better for carrying. Hate the half moon clips you get with the Smiths PITA to load and unload.

.41Dave
December 27, 2006, 03:56 PM
If you want a reloader's dream, get a .41 Magnum. I've never owned one that wasn't wonderfully accurate and easy to work up an accurate load for.

treebeard
December 27, 2006, 04:25 PM
I saw 4 .45ACP revolvers today that looked really nice, but the place I went to was mobbed. All 4 were 625's and one looked brand new. I will go back at the end of the week when it is less busy.

If you enjoyed reading about "Revolver caliber suggestions" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!