My Ruger P95 has loose slide when cocked..


PDA






bigpea
August 5, 2007, 09:31 PM
I own a Ruger P95DC and have been very happy with it so far. Today after a range session I field stripped and cleaned the gun which I have done many times before but this time I noticed something I have never noticed before. After I put it back together I cocked it and while the hammer was back it felt loose. It makes a rattling noise when you move the gun around. There is a slight movement of the slide, i've never noticed it like this before. It's only when the hammer is back, when it's down there is absolutely no movement what so ever. I can push the slide with my fingers and there is a slight movement back and forth which is causing it to feel loose and make the rattling noise. Maybe about a millimeter or so of loose give. The trigger feels a lot looser when it's cocked as well.

I took it apart and put it back together again 4 or 5 times and it's still doing it. My question is does anyone else who owns a P95DC experience this same rattle?

Thanks for any help, it's much appreciated.

If you enjoyed reading about "My Ruger P95 has loose slide when cocked.." here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
lee n. field
August 5, 2007, 10:25 PM
Got the recoil spring oriented right? That's about the only thing you can muck up during a routine field strip, though that's not going to affect the hammer the way you describe.

Call Ruger, talk to them, would be my recommendation.

Product Service - Prescott, AZ — Service inquires for Pistols and Police Carbines
Sturm, Ruger & Co., Inc.
Product Service Department
200 Ruger Road
Prescott, AZ 86301

Telephone: 928-778-6555 / Fax: 928-778-6633
(Monday through Friday 8:00am - 5:00pm MST)

armabill
August 5, 2007, 10:46 PM
Mine was the same way. It was really loose, the whole gun was loose.

I called Ruger and got in touch with their engineering department. He got the blue prints out to check the tolerances.

He said that the tolerances on the print were the same as the tolerances that I measured. It's that way so the gun will function no matter the what.

I thanked him for his time and promptly sold the gun. It functioned but wasn't accurate.

W.E.G.
August 5, 2007, 10:53 PM
One of the nicest features of the P95 is it is very easy to operate the slide to charge the weapon. This is probably a function of the "tolerances." Some folks who can't seem to handle centerfire semi-autos really take to the Ruger quite well. Not an impressive gun to a sophisticate. But a godsend to the tyro or the arthritic.

Gbro
August 5, 2007, 11:01 PM
I just checked mine and it dose in fact have a dull rattle to it. However once the mag is in, the looseness goes away.
The moral of this is, "Don't point an unloaded P97DC at the BG if you have the shakes"
This gun is unfired post Ruger repair. It was sent in for DAO"ing. Now that it is back i kind of wish it was a DAO full time...

Steve C
August 6, 2007, 02:09 AM
My P90 will rattle, my 1911's all rattle a bit too but that hasn't anthing to do with how well they shoot so don't worry about it.

HiroProX
August 6, 2007, 03:55 AM
If it bugs you, put some grease on the slide where it meets the rails on the frame. Takes the rattle right out of my P-85 Mk.II and out of my KP-345PR.

bigpea
August 6, 2007, 11:28 AM
UPDATE: I just spoke with Ruger Tech Dept. and they told me that this rattle and slide movement is normal. I asked why and they said that's just the way they engineered it. HMMMM.....OK! Well i've been happy with it but I am going to start looking for a .40cal for my primary soon so I guess I'll just deal with it.

Thanks for everyones input and feedback, it's much appreciated.

bigPEA

novaDAK
August 6, 2007, 11:54 AM
My P89DC does it like you describe, only when the hammer's cocked. The slide (noticed at the rear) will move slightly side to side on the rails. Mine shoots every time and it's as accurate as my hi-power. But you must remember that when the gun fires, and tight lockup is needed to contain the chamber pressures, the hammer is forward after you pulled the trigger to fire the gun :) I haven't noticed it on my P95 or any of my other Rugers for that matter.

bigpea
August 6, 2007, 11:56 AM
novaDAK- You don't have the looseness on your P95 though when the hammer is cocked?

bigPEA

Surefire
August 6, 2007, 08:06 PM
When I use to have a P97, it did this. Its normal IMO.

If you enjoyed reading about "My Ruger P95 has loose slide when cocked.." here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!