Mossberg 500 Trigger Detail Strip and Assembly


PDA






casaceli
November 26, 2007, 11:23 PM
Does anyone have a link to, or can anyone provide, detailed instructions on the disassembly and reassembly of the Mossberg 500 trigger group. I plan on doing some stoning and polishing of the contact surfaces to improve the trigger pull on my deer/slug-only 500 and was looking for some guidance with the trigger group.

I do have experience in different trigger groups as well as have done a couple of my own trigger jobs (encore/model 700) in the past but was hoping to find some detailed assembly/disassembly info for the trigger group.

Thanks,

Happy Shooting

If you enjoyed reading about "Mossberg 500 Trigger Detail Strip and Assembly" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
BoomStick82
December 13, 2007, 02:30 PM
*bump* anyone???

NY'er
January 3, 2008, 08:50 PM
I can't help you myself, but perhaps someone over at www.shotgunworld.com might have that information.... If you scroll down you'll see a Mossberg Lovers forum, and if you do find out, please report back as I'm sure some other THR'ers would benefit from it as well!

Good luck, and Happy New Year!

GeorgeR
January 3, 2008, 09:12 PM
Hi. PM me your email address and I'll send you illustrated instructions.

tweetertx02
January 4, 2008, 11:48 PM
11111111

tweetertx02
January 4, 2008, 11:49 PM
georgeR i would like those as well if you could do the same for me

biermkr
April 30, 2008, 01:35 PM
pm sent to you george

GeorgeR
May 1, 2008, 08:31 PM
emailed instructions to both of you last night. George

john917v
May 7, 2008, 02:01 AM
I, too have wanted to shine up the trigger on my Mavy. 88. Is the trigger group on the 88s and the 500s the same? Mine is a 12-ga. field-model. Thanks.

kallyjk
September 18, 2008, 01:42 PM
Bringing this back from the dead. Found this in a search and was wondering if anyone that has the instructions can send them to me?

plumbum
October 22, 2008, 09:49 PM
Hello there, I am attempting to help a friend reassemble the trigger assembly for his mossberg 590. He was installing a new stock or grip or somesuch and apparently the bolt was too long and broke his safety. Long story short he has aquired the part he needs but somehow disassembled or had the trigger assembly 'pop apart' on him. I am attempting to help him reassemble it but being its a new shotgun, there are no wear marks from the springs on the interior of the assembly, and i can not determine how to reassemble it. Mainly where the springs are hooked on to or resting against. They should seriously make reassembling this trigger assembly without a guide part of some sort of cognitive test. I'm usually good at stuff like this and so is my friend, but were completley stumped. :/

I would greatly appreciate your help if you could forward any resources that would help me in my quest! thanks!

davidbm125@sbcglobal.net

havoc7usmc
October 22, 2008, 11:20 PM
I made a tool for reinstalling the sear and spring. I made it out of a CZ52 pistol cleaning rod with a little grinding it works like charm.

Riss
October 25, 2008, 04:14 AM
Check over on www.lifelibertyetc.com Not sure if their Mossberg video goes into the trigger group or not, but it might. It is in their Range Bag page, somewhere near the bottom I think. If you need a manual I am sure I have it, I have almost everything (and I do mean everything) in Pdf format. About 200 or so. If you need a copy send me an email.

Bad Hammer
December 2, 2008, 08:00 PM
Hi. PM me your email address and I'll send you illustrated instructions.

I know I'm a little late, but GeorgeR if the offer still stands, PM sent.

If you enjoyed reading about "Mossberg 500 Trigger Detail Strip and Assembly" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!