SKS Gas Tube Cleaning


PDA






Dynasty
April 9, 2008, 01:52 AM
What is the best way to get all the built up cosmoline and/or debris out of an SKS gas tube? I want a spotless gas tube, but cannot find an object to clean it out with. Any suggestions?

If you enjoyed reading about "SKS Gas Tube Cleaning" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
Dr. Peter Venkman
April 9, 2008, 01:59 AM
Spray the inside of it with Breakfree and Gunscrubber. Then, take a very thin cloth (at least as thin as a napkin) or heck even a napkin, and stuff it in the fat end of the tube. Take the piston and ram it in, then do the reverse on the small side and push it back out. Do the same for the smaller part of the tube with a smaller cloth/napkin.

jpwilly
April 9, 2008, 02:14 AM
"spotless"

Nutz!

jrfoxx
April 9, 2008, 07:52 AM
Spray the inside of it with Breakfree and Gunscrubber. Then, take a very thin cloth (at least as thing as a napkin) or heck even a napkin, and stuff it in the fat end of the tube. Take the piston and ram it in, then do the reverse on the small side and push it back out. Do the same for the smaller part of the tube with a smaller cloth/napkin.
Never thought of using the piston to help out like that.Great idea. Break free, gunscrubber, or *gasp* el-cheapo brand non-chlorinated brake cleaner works great on ALL tough and/or organic stuff, and is easy to get in harder/smaller places since it just sprays in. Cant picture how lone or big around the sks gas tube is ( never cleaned either of mine), but pipe cleanes, a .22lr cleaning rod with patches, Q-tips etc would work too. (again, all depending on length and diameter). Dr. Peter Venkman's idea may still be the best and easiest though.no idea.

dispatch55126
April 9, 2008, 08:13 AM
I clean mine alter each range session. For cosmoline, bake the tube like all the other parts and just wipe it out.

After each session, I spray foaming bore cleaner down then patch it clean. The near side is about .22 caliber but the gas port size nears .45/.50 caliber.

DMK
April 9, 2008, 08:19 AM
I find that Hoppe's #9 or simple mineral spirits cuts through cosmoline very well. I use mineral spirits to clean up old milsurps caked in cosmo.

Just let it soak a bit.

A 45ACP bore brush covered with a patch or piece of t-shirt makes a good gas tube scrubber.

Whatever you use, wipe it dry. Don't leave the gas tube or piston wet with oil. It will burn up and leave a tough layer of carbon.

aka108
April 9, 2008, 10:30 AM
Use a 12 ga shotgun brush with a patch wrapped around it. Saturate 1st patch with solvent and scrub the a 2nd dry patch will will finish the job.

kingjoey
April 9, 2008, 11:15 AM
Use a 12 ga shotgun brush with a patch wrapped around it.

Do you mind explaining how you plan to get a brush that is apx .750" in diameter into a bore that is apx. 510" in diameter? :scrutiny:

ColinthePilot
April 9, 2008, 01:48 PM
I want a spotless gas tube

Using the term "spotless" in the same sentence as "SKS" is pretty much futile. I've never even seen them in the same BOOK. Just give up now. :neener:

Cmdr. Gravez0r
April 9, 2008, 01:50 PM
good info here, but as always the SKS experts are

www.sksboards.com

I know I pimp "my" board all the time, but it's too good to pass up for people wanting to iron the quirks out of these nifty rifles.

Dynasty
April 9, 2008, 08:28 PM
Is the goal to get the top of the piston head with no black carbon on it? Or will there always be some sort of carbon on it?

Buzzbox
April 9, 2008, 08:35 PM
Cleaning an SKS after every range session? Wow. I think I've cleaned mine. Once. Maybe. :D

xsquidgator
April 9, 2008, 09:27 PM
Cleaning an SKS after every range session? Wow. I think I've cleaned mine. Once. Maybe.

Well, maybe every 2 or 3 range sessions. :)

Now "spotless" is not a word I would ever use to describe my SKS' gas tube, and I'm the only person who's ever shot it too. No matter what I scrub it with, no matter what solvent, there is always more soot and dirt ready to come out. I try to get it pretty clean but after all this rifle was meant to be used in the jungle by poorly trained and equipped troops. I don't worry much about it.

esmith
April 9, 2008, 11:00 PM
Go down to walmart or your local dollar store and buy some cheap brake cleaner or carbuerator cleaner. Then go home and blast the living hell out of the gas tube. Don't get it on the wood though, that would be bad. Works well.

If you enjoyed reading about "SKS Gas Tube Cleaning" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!