How do you clean/polish aluminum alloy frame?


PDA






Lancel
September 12, 2003, 11:29 PM
I have a Taurus 731 ultralight. The aluminum frame has some blackened areas that are apparently corrosion from perspiration.

I've tried all kinds of things to clean it up without success: Hoppe's Gunmetal Polish, Ultra Brite polish, FP-10, Breakfree, Shooter's Choice Solvent, even Simple Green.

My best luck was with a pencil eraser and much effort. Any suggestions on how to clean aluminum alloy?

Larry

If you enjoyed reading about "How do you clean/polish aluminum alloy frame?" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
JohnKSa
September 13, 2003, 01:39 AM
Never, NEVER use any type of abrasive methods to clean aluminum.

Aluminum gun parts are typically anodized which provides a completely corrosion resistant finish that is also VERY hard. If you remove or penetrate this finish you are left with a corrosion prone surface of relatively soft aluminum.

Home anodizing is possible but probably not something the average gun owner is going to be willing to do.

Your only option, as I see it, is to cough up to have the frame profesionally re-anodized, or strip the frame, have it bead or sand blasted and then refinish it with one of the bake-on epoxy/teflon/moly finishes available from Brownells.

Polishing it further is only going to exacerbate the situation.

You could also contact Taurus and see if their lifetime warranty will help you in this situation since the frame should not have corroded in the first place (unless someone removed the anodizing somehow).

Lancel
September 13, 2003, 11:59 AM
JohnKSa:
That's good advice on anodized aluminum. In this case, the frame appears to be an alloy through and through and not anodized. Wear marks (eg. cylinder pin against frame opening) don't show the tell-tale broken finish appearance of scratched anodizing.

Now that I think of it, what gives color to aluminum frames like the M-16 and Berettas? Are they anodized?


Larry

nondescript
September 13, 2003, 05:57 PM
Lancel- I believe that colored dye is added while anadozing, sealing the pigment into the surface finish. A bead blasted finish like on an AR will look duller than a highly polished finish like most aluminum flashlights.

buttrap
September 14, 2003, 04:04 AM
The Taurus alum frames are just like on a ruger stainless 10/22 action, polished alum with a clear spray coat for a finish. No anodization at all.

Lancel
September 14, 2003, 03:30 PM
Thanks, all.

I plan on calling Taurus on Monday to see what they have to say about frame beautification.

Unfortunately, it's one of the many companies that you don't talk to a real technician without struggle and I usually know more than the first level or two of customer service.

In the end, my best support may be the internet gun community.:)

Larry

JohnKSa
September 14, 2003, 04:21 PM
Lancel,

I never considered the possibility that it might not be anodized...

If Taurus won't help you and you don't mind a black frame, GunKote from Brownell's is supposed to be pretty good stuff. Probably one of the best bake-on finishes you can put on. You will have to sandblast though.

Another option (pricier) is to send it off to Robar and have them do an NP3 finish. I believe that NP3 coats well over aluminum. That would leave you with a silver colored frame that would be corrosion proof, and very tough.

Lancel
September 14, 2003, 06:44 PM
GunKote from Brownell's or send it off to Robar may end up being my best options.

Thanks,
Larry

4v50 Gary
September 14, 2003, 09:06 PM
Leave it alone. You don't want to ruin the anodized finish.

Lancel
September 17, 2003, 01:55 AM
Leave it alone. You don't want to ruin the anodized finish.
Can't ruin the anodized finish 'cause it's NOT anodized.:)

Confirmed this today with Taurus. Not sure about the exact alloy, probably 4041; the tech is going to check with Brazil and email me. But it's not anodized; it's an aluminum alloy.

Taurus uses WD-40 to clean it up. The tech said if that didn't do it, then send the pistol to them and they'd fix up.

That's good customer care. I'll decide what to do after I find out the exact alloy.

Larry

Lancel
August 20, 2004, 01:23 PM
This is a followup and clarification:

After many attempts, I've been unable to get more information from Taurus. No response by email or phone from the tech (Anthony) who originally told me (1) the alloy was 4041, (2) the frame wasn't anodized, and (3) he would get more info from Brazil.

Since then I've found out there's a steel alloy 4041 so even the aluminum alloy info is in doubt.

My conclusion is that if WD-40 doesn't clean your Taurus ultralite then follow 4v50 Gary's advice and leave it alone or return it to Taurus (who will probably use WD-40).

Regardless, I traded the Taurus and now have a stainless steel Ruger SP-101.:)

Larry

CWatson
August 20, 2004, 03:27 PM
Mag Wheel cleaner,any brand from PEP BOYS or similiar auto parts store.


CWatson

RJ357
August 24, 2004, 07:54 PM
Is this it?

taurus 731 (http://www.taurususa.com/products/product-details.cfm?model=731SSULC&category=Revolver)

Looks like stainless

Lancel
August 25, 2004, 12:10 AM
RJ357:

The Taurus ultralite frame is aluminum alloy (maybe anodized) while the cylinder and barrel (liner?) are stainless steel.

Larry

StressPuppy
August 25, 2004, 01:21 PM
Chiming in late, but what about something like Flitz polish?? Has worked wonders for me in the past.

Just a thought....

Lancel
August 25, 2004, 02:15 PM
Thanks for all the input folks.

Regardless, I traded the Taurus and now have a stainless steel Ruger SP-101. :) :) :)

Larry

JNewell
August 25, 2004, 02:18 PM
Simple Green

Don't use that on aluminum. It can damage/remove anodizing and damage the aluminum. (This is on the mfr's website, btw.) I have seen it damage an aluminum SIG frame.

Best stuff for this IME is MPro 7.

If you enjoyed reading about "How do you clean/polish aluminum alloy frame?" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!