which of these kits...


PDA






kurts_armory
December 25, 2008, 01:06 AM
ok, i can get one of these PARTS KITS. each is the same price. Which would YOU take out of the three and why? thanks




A. no rec included... refinished wood/ metal. price does not include FCG has 150 +/- rds fired.
http://i285.photobucket.com/albums/ll49/kurts_armory/romya.jpg
B. no rec included... Like new kit, all parts included, SAR stock set
http://i285.photobucket.com/albums/ll49/kurts_armory/sar.jpg
C. no rec included... Like new WITH PAPER WICK in barrel, completely demilled. all parts included
http://i285.photobucket.com/albums/ll49/kurts_armory/ak1.jpg

If you enjoyed reading about "which of these kits..." here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
kurts_armory
December 25, 2008, 01:50 AM
come on people this is a matter of opinion here... just want a little help :)

Gunfighter123
December 25, 2008, 03:30 AM
I would get "C" if all priced the same, my reason is -"Hey , it's a G thing !!!!!

Starship1st
December 25, 2008, 11:08 AM
I already own "C", I would get "B" if the price is noticeably less than "A". :cool:

Hoppy590
December 25, 2008, 01:26 PM
C will require an FFL, as would A i believe.

i vote for A. now,then get C or B to save for a rainy day :)

JWarren
December 25, 2008, 01:57 PM
He said that "No Receiver" was included in any of the kits, so I assume that the pics are representative of what he gets.


If that is the case, Go with C. I like the Rommy "G" rifles.

Any will be fine, it just depends on what you want.


-- John

shotgunjoel
December 25, 2008, 02:11 PM
Get A, wonderful wood. I kinda like the lighter colored wood.

hawmanai
December 25, 2008, 03:14 PM
Without actually getting to see them in person.

I would say B.

A needed to be reconditioned, might have been rusty or well used.

C, I recently got a similar Romy kit from J&G and it was not stored very well.

Where and how much are you getting these from?

You have to have a certain amount of US made parts and replacing the FCG and stock are the most commonly swapped.

kurts_armory
December 25, 2008, 05:44 PM
if i get any of them i will probably find somenone who can bead blast it for me, and then i will put on a couple coats of alumi-hyde II

zoom6zoom
December 25, 2008, 10:32 PM
I'd lean towards C. Both B and C are Romy G's, but C has the correct lower handguard. The big plus is that it has already been demilled, which will save you a lot of work. Drilling out the old rivets can be a major pain. And the barrel has already been pressed out of the trunnion. This kit is ready to build. You just need rivets and your US compliance parts (and a receiver or flat if the one in the picture isn't included.

"A" not including the FCG is no big deal as you'll want a US made one to count as three of your required six compliance parts.

If they are under $275 each, get them all!

kurts_armory
December 26, 2008, 11:37 PM
I decided to get b. thanks guys

If you enjoyed reading about "which of these kits..." here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!