lee Reloader single stage press


PDA






kestak
October 29, 2009, 01:20 PM
Greetings,

Anyone found out a way to have the primers not to fall all over when using this press? Maybe there is something I did not get. The hole is in the back of the ram and nothing is there to catch the primers..

Thank you

If you enjoyed reading about "lee Reloader single stage press" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
fireflyfather
October 29, 2009, 01:45 PM
There is a hole near the primer exit opening in the ram that allows the primers to (95% of the time) fall into the body of the press. I mounted my press on spacers and have a small plastic tray under the body of the press to catch the primers that go where they are supposed to. For the 5% that go flying around, may I suggest a hand-held vacuum? Either that or a press with a primer catching system (classic cast, etc)

rcmodel
October 29, 2009, 02:38 PM
I made a riser block with a slide-out aluminum tray to catch the primers.
I just clamp the block down to the bench when I use it for de-priming.

http://i81.photobucket.com/albums/j219/rcmodel/KTOG/Leepress.jpg

rc

KSCCHTrainer
October 29, 2009, 02:42 PM
Greetings,

Anyone found out a way to have the primers not to fall all over when using this press? Maybe there is something I did not get. The hole is in the back of the ram and nothing is there to catch the primers..

Thank you
Using a pice of 1/2" PVC water pipe and an old funnel, I cut out one side of the funnel top, bent the PVC at a shallow angle to allow the primers to fall into an old coffee can hung off the end. I jury rigged a bracket to hold this assembly up close to the slot in the ram and now almost all of the spent primers land in the funnel and are carried into the coffee can catcher. You'll have to figure out the angles yourself as no two people mount their presses the same. PVC pipe is easy to bend if you have a heat gun.

The Bushmaster
October 29, 2009, 02:47 PM
I like rc...I have an old aluminum ice tray under my bench with a hole drilled clean through the bench top under my Lee single stage. It takes a long time to fill that tray...

psyop
October 29, 2009, 02:49 PM
rcmodel

Nice

kestak
October 29, 2009, 03:44 PM
Greetings,

I got it!!!! I know what I'll do tonight....

Thank you VERY MUCH guys!

bullseye308
October 29, 2009, 10:41 PM
I bolted my Reloader to the bench over a hole drilled through the bench. Under the press I nailed a baby food jar lid with a large hole in the lid. When the jar is full unscrew it and dump it in a gallon pickle jar, then screw it back on to continue. I don't have to remove the press ever.

mrdo1
October 30, 2009, 08:24 AM
Kestak, I have the press that came with the anniversary set, the primers went everywhere until I read the instructions and put the metal primer arm into the ram when depriming, since then I haven't had any go anywhere but in the primer catching tube.

ranger335v
October 30, 2009, 07:14 PM
Love those little Lee presses for de and re capping. I have a 3/4" hole under my decap Reloader and a short tube in it that empties into a pill bottle. But I really like RC's solution too, I though my solution was easy to do but it's not THAT easy! Good idea RC.

I was losing an occasional spent cap out the side of my ram too. Didn't like that, so I glued (Crazy Glue) two narrow strips of scrap rubber, 3/16" thick, 1/4" wide, 1 1/2" long to the body, one strip on either side of the vertical hole. Those filled the narrow body-to-ram gap and I lose NO spent primers now. Wood or plastic strips would work as well.

BHP FAN
November 1, 2009, 01:23 AM
RC,YER A GENIUS![seriously]

Gadzooks Mike
November 1, 2009, 10:15 AM
I was having the same problem with my Lee turret press. Then I found out accidently one evening that if I just installed the primer seater thing (http://www.leeprecision.com/graphics/parts/2889.jpg), it forced the spent primer into the hole it's supposed to go.

The Bushmaster
November 1, 2009, 10:43 AM
I, also, found that if I stuff a piece of styrafoam (fitted) in the priming adapter slot that directs the primers properly and I don't have to have a priming system, that I don't use, installed just to direct spent primers...

Gadzooks Mike
November 1, 2009, 10:25 PM
Bushmaster - good idea. I tried a piece of plastic drinking straw with only so-so results. Might try the styrafoam idea. It is silly to have to install a primer piece to deprime a case. Kind of like pressing Start on Windows when you want to End.

If you enjoyed reading about "lee Reloader single stage press" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!