barrens 22-250, 45gr solid ,load info wanted


PDA






atvalaska
January 26, 2010, 03:48 PM
my gun up to now Only likes 40moly v-maxs,but on "fur" it ten's blow'em up..so i found a box of these ,and i'm going work up a load..any one here try them yet?http://barnesbullets.myshopify.com/products/22-cal-224-45-gr-bnd-spit-bt

If you enjoyed reading about "barrens 22-250, 45gr solid ,load info wanted" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
fireman 9731
January 26, 2010, 05:38 PM
Bullet Weight: 45 gr
Case Trim Length: 1.902"
S.D. 0.128
Bullet Style: Banded Spitzer Solid
Primer: Fed GM210M
B.C. 0.195
COAL: 2.350"
Barrel Length: 24"
Case: Winchester
Twist Rate: 1:14"
Bullet Weight: 45 gr
Case Trim Length: 1.902"
S.D. 0.128


Powder
TAC- 34.0grs (start)@3664fps up to 37.5grs(max)@4015fps
AA 2520- 37.5grs (start)@3727fps up to 41.0grs(max)@4060fps

Here is info from the Barnes website, I don't have the manual handy, but my 22-250 really likes varget with lighter bullets.

Here is the link to Barnes: http://www.barnesbullets.com/images/22-250RemingtonWeb.pdf

atvalaska
January 27, 2010, 01:09 PM
there web site is up:eek:!! :) did u try them ?

fireman 9731
January 27, 2010, 03:18 PM
I haven't specifically tried their 45gr banded spitzer but i have used the 36gr varmint grenades and the 52gr TSX, both with good results. I have also had very good results with 45gr CTs and Nosler ballistic tips.

What kind of gun are you shooting?

atvalaska
January 29, 2010, 01:49 AM
well atleast its the 1st year that they came withe the blk "plastic ' stock...i've post on here beforeabout it the only factory round it shoots well is the moly 40gr v-max.(shoots better than i can)..every thing else is all over the place....but i need a "better bullet" and a good punch,Deep and less fur damage...

fireman 9731
January 29, 2010, 01:54 PM
You might want to give the CTs a try, they are 'Lubalox' coated- sorta like moly.
http://nosler.com/index.php?p=3&bullet=10

The Barnes varmint grenades are designed with fur hunters in mind. The have a small entrance wound, with no exit. I have good luck with them, but anything smaller than a fox gets turned to goo.

If your rifle likes lighter bullets, which it sounds like it does, give the 36gr ones a try, the heavier ones require a faster twist like 1:12 or 1:10. Most 22-250s are 1:14.

You may also want to look at the 40gr BlitzKing from Sierra. But if you are looking for more punch and are limited to lighter bullets you are in a tight spot. The Barnes banded spitzer is a good choice. I don't know what the difference between it and the TSX is but the TSX is available in 45grs as well and will hold up for sure, but you are going to have an entrance and exit wound.

If you are still chasing bullets around your target then it might be time to try a few different powders, Varget is a favorite of mine, H-380 is also the go-to powder for the 22-250.

What are you hunting?

atvalaska
January 30, 2010, 01:24 PM
wolfs some yotes and fox...the yote the other day did not like the 40vmax it took 2.... a fox it kills good , with a little sewing ...

billybob44
January 30, 2010, 11:10 PM
My Remington Varmint likes 50-55gr. bullets. My hunting load, for groundhogs, and yotes, is a Hornady V-Max 50/55gr. I load the bullets up to about 3500fps. for the proper explosion factor in a varmint. This load will vaporize a 3 gal. water jug, and just leave shards of bullet material in jug-no exit hole-just blows up. I have not opened a groundhog after a center mass hit, but when you shake the carcass, it sounds like a bowl of pasta sloshing around inside??:scrutiny::uhoh:

If you enjoyed reading about "barrens 22-250, 45gr solid ,load info wanted" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!