How/where to mount the RCBS Uniflow measure?


PDA






Leaky Waders
March 2, 2010, 07:13 PM
Hi,

I have the rock chucker supreme kit and it came with the uniflow powder measure which I have yet to use..been using a dipper instead.

Now, I want to vary my powder charges and have decided to use it.

How do you guys have it mounted for easiest use? Do you have it on your bench or on the press or some other mount?

Just curious.

L.W.

Ps I'm using it for 45 long colt and 45 schofield.

If you enjoyed reading about "How/where to mount the RCBS Uniflow measure?" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
Greg Mercurio
March 2, 2010, 07:23 PM
Buy a stand. RCBS makes one for this unit. The stand needs to be rigid, you'll feel the cutting action with stick powders.

Cabela's has them so do many others.

http://www.cabelas.com/p-0002912210606a.shtml

billybob44
March 2, 2010, 10:06 PM
Buy a stand. RCBS makes one for this unit. The stand needs to be rigid, you'll feel the cutting action with stick powders.

Cabela's has them so do many others.

http://www.cabelas.com/p-0002912210606a.shtml
I use this RCBS stand with complete satisfaction..

dakotasin
March 2, 2010, 11:19 PM
i have it on the press - sandwiched between the press and the nut on the dies.

oneounceload
March 2, 2010, 11:24 PM
Buy a stand. RCBS makes one for this unit. The stand needs to be rigid, you'll feel the cutting action with stick powders

Another vote for the stand. I can use a 50-count reloading block under it and reload them all very easily

lgbloader
March 3, 2010, 12:25 AM
Another vote for a stand here. I have a couple of different mounts, the plate with two holes, and a stand. I also go direct to the press with my T7, just twist the turret.

LGB

twofifty
March 3, 2010, 01:05 AM
If you use the stand, locate it pretty close (7"-9") to the press, but further back from the bench's front edge. For efficiency's sake, you want to shorten your hand & arm movements as much as possible, but without any of the tools & accessories getting in your way. Think of the layout as if you're setting up a small factory.

Fatelvis
March 3, 2010, 06:49 AM
Definately get the stand.
I have a Uniflow on the stand, and the stand is screwed to a 12"-14" section of 2X10 plank, that is clamped to my loading bench, when in use. This lets me bring it out into the open when in use, and put it away quickly after use, leaving an "uncluttered" work area. (I had to use quotes around that word, because if you saw my bench, it's anything BUT uncluttered!)

bertus
March 3, 2010, 07:26 AM
get the stand and for mobility mount it on a brick or tile,so you can move your uniflow around

edSky
March 3, 2010, 09:50 AM
agree with the stand folks. I'm a righty, my press is towards the left of my bench, the Uniflow and stand are about 6 or 9 inches to the right.

Rembrandt
March 3, 2010, 10:08 AM
Lots of good ideas, the RCBS mount is hard to beat. I've seen them mounted upside down from an overhead shelf and right side up.

http://img.photobucket.com/albums/v405/Rembrandt51/reload%20room/IMG_7566.jpg

Lonely Raven
March 3, 2010, 11:35 AM
When are you going to finish those walls Rembrandt? Maybe you should...paint them? :P

Leaky Waders
March 3, 2010, 11:36 AM
Wow nice setup, and I appreciate the idea of mounting the stand on a piece of wood or tile or something.

Rembrandt, are your bases factory made or did you make them from some stock steel?

Also, do you guys use the baffle in the uniflo or is that some kind of gimmick? It looks like something I could make with a coke can...

Rembrandt
March 3, 2010, 11:38 AM
...When are you going to finish those walls Rembrandt? Maybe you should...paint them? :P

Heehee.....when they're done it will be like no other. Just haven't found the right ceramic tile at the right price yet.

Rembrandt
March 3, 2010, 11:44 AM
....Rembrandt, are your bases factory made or did you make them from some stock steel?

Neither, it's 1/2" PVC sheet. Stronger than wood, moisture & chemical resistant, can be cut-drilled-shaped with common wood working tools.

http://img.photobucket.com/albums/v405/Rembrandt51/reload%20room/IMG_0577.jpg

ranger335v
March 3, 2010, 11:59 AM
Your question is a very good one. Most of the photos I see of equipped benches rarely have a set-up that's helpful to a good, smooth work flow. A sturdy fixed powder measure stand is VERY GOOD way to start!

I'll note that most of those who say loading with an electronic scale and/or digital powder dumpster is "faster" probably have their conventional tools poorly positioned for easy work. I've tried digital gear at friend's houses. With my present tool placement I find I would get very little benefit with all that stuff and do it at greater cost and MUCH lower durability.

First, let me say what to avoid; a press-mounted measure; mounted on the front edge of the bench; mounted a step or more away from the press; mounted where it eats a lot of open bench space. All of that is awkward and slow to deal with and/or eats more working space than it should.

Find your own 'best' location. Start by standing at your press in your normal working position, leaning your body against the front edge of the bench and just a bit away from the press so you'll have sufficent arm freedom to work the measure. With your measure fixed in a stand, shift it around with your so you can easily reach the measure's lever without moving. That will likely position it about 12'-14" back from the bench front for most right handers and just a few inches to the left of the press. Position the stand base immediately behind the press, tuning/angling it so you can have the measure handle placed where you want it and the stand itself won't interfer with your use of the rest of the bench top. Test mount it with wood screws until you decide if that's exactly what you want before you mount it permanently. (You can easily fill excess holes in the bench with epoxy.)

Next, with the measure in place, make a convienent place for your beam scale and powder trickler. Build a sturdy shelf, wide enough to position the scale within easy reach of the measure, where it will be easy to reach and read too. For very easy reading, place it so the scale's beam is about chin high. (I prefer a wall mounted shelf to prevent bench vibration/shake from interfering with the scale.) Put your powder trickler between the measure and scale pan. Test your work flow and make refinements until you get it all exactly where you want it before mounting anything permanantly.

Properly arranged, you will be able to stand at the press and do your loading work easily. Easy is quick. You will have open bench space for loading blocks and bullet boxers between the measure and bench front, immediately to the working side of your press, allowing for very smooth work flow without wasting time fumbling and moving around. You can smoothly drop charges directly into cases held in a loading block OR measure/weigh each charge and pour them through a powder funnel before seating, all without taking a step.

GP100man
March 3, 2010, 12:32 PM
I mount mine on the left on a mount , I even made a couple of stands .

http://i746.photobucket.com/albums/xx110/GP100man/102_0208.jpg

rfwobbly
March 3, 2010, 08:49 PM
I like mine on a stand, with the stand mounted to a separate chuck of something heavy. Since the Uniflow is only used for one part of the reloading process, it can then be pushed to the back of the reloading area to keep the "decks clear and ready for action" on other fronts. Like thus....

http://lh3.ggpht.com/_E3bV2jGIaSg/S3YucAyMIEI/AAAAAAAAArs/lBXxhRRL5RM/s720/IMG_3527.JPG

ranger335v
March 3, 2010, 08:55 PM
GP,you have your measures in the "right" place. Have you tried putting that dandy ol' Herter's scale on the shelf behind the measures? It would be a lot easier to read.

GP100man
March 3, 2010, 11:13 PM
Yeah! it was just posing to get it all in the pic!

I posted it on another forum to see if I could get dates on time of manufacture??

From my research on Herters I thinkin early 60s???

The scale I use is this ole Webster , It`ll weigh dust!!!!

http://i746.photobucket.com/albums/xx110/GP100man/102_0200.jpg

If you enjoyed reading about "How/where to mount the RCBS Uniflow measure?" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!