Reloading with a little disability


PDA






jamesicus
October 5, 2010, 02:06 AM
I am in extended recuperation from a botched abdominal surgery that resulted in a massive infection from a punctured intestine. In consequence, I am at present tethered to a wound vac machine with very limited mobility. At least I got to celebrate my eighty-first birthday with a hospital room party!

Needless to say my reloading and shooting activities have been somewhat curtailed during my convalesence. Although I have a well-equipped reloading room, I am now producing "home brew" cartridges for my CZ 550 American 30/06 caliber bolt action rifle (eventually other rifles/calibers also) while seated at a comfortable patio table - the most relaxing and enjoyable reloading I have experienced in some sixty years. I am presently producing reloads using the following equipment, components and methodology:

Equipment:

Lee hand press

RCBS 30/06 neck sizer/bullet seater die set

RCBS #3 Shell Holders

Lyman large rifle primer pocket uniformer

RCBS chamfer/deburring tool

Nylon bristle bore brush (inside neck cleaning/lubricating)

Lee cartridge case lube (for inside neck lubrication)

RCBS hand priming tool

Dial Caliper

Lee powder dipper (15 grains)

RCBS powder funnel

000 steel wool

Small flashlight

CZ 550 American 30/06 caliber bolt action rifle with firing pin mechanism removed

Components:

Winchester brass

CCI 200 large rifle primers

Hodgdon IMR "Trail Boss" powder

Hornady .30 cal 150 gr FMJ/BT bullets

Methodology (twenty reloads per session):

1. Inspect cases for flaws

2. Clean cases using 000 steel wool

3. Clean and lube inside case neck (nylon bore brush/Lee case lube)

4. Size and de-cap using RCBS Neck Sizer die (Lee Hand Press)

5. Clean primer pocket using Lyman uniformer

6. Check case length (Dial caliper)

7. Deburr/chamfer case mouth - inside and outside

8. Check chambering/bolt closure using rifle (without firing pin mechanism)

9. Seat primers using RCBS hand tool

10. Check chambering/bolt closure using rifle (without firing pin mechanism)

11. Charge (15 grains) cases with Trail Boss powder using Lee dipper

12. Check each case charge using flashlight

13. Seat bullets using RCBS seater die (Lee Hand Press)

14. Check chambering/bolt closure using rifle (without firing pin mechanism)

15. Inspect each cartridge - finish using 000 steel wool - Wipe off using rag/lighter fluid


I am an old-time competitive high power rifle (mostly 30/06) shooter who loves to shoot accurate bolt action rifles. Now that I am in my eighties I really enjoy comfortable paper target shooting from the bench. I doubt I will ever hunt animals again, but I do love shooting! Diminished eyesight and trigger finger tremor dictate that I use optical sights and rifle rests. Shooting full power 30/06 (and more powerful) loads is uncomfortable for me now - the recoil and muzzle blast really bothers me - but I derive great pleasure shooting at the range. As for reloading, brass seems to last forever using the reduced Trail Boss loads thereby reducing expense significantly. Shooting from the bench is now a joy (even during lengthy range sessions) and the accuracy I am obtaining is most satisfying.

JP

If you enjoyed reading about "Reloading with a little disability" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
bds
October 5, 2010, 02:21 AM
Ouch!

Maybe the hand press will provide some physical rehab therapy? :D

I use a portable castered reloading bench - perhaps you can mount a press that can be operated from your seated position?

http://www.thehighroad.org/attachment.php?attachmentid=128002&stc=1&d=1285098052

jamesicus
October 5, 2010, 02:48 AM
Thank you for the suggestion, bds. Actually I really enjoy reloading seated at the patio table: the ambience is delightful and I find neck sizing 30/06 cartridges using the Lee hand press very easy.

JP

bds
October 5, 2010, 02:54 AM
James, once I built my first portable bench and sized some brass while watching the sunset in the cool patio and sipping iced tea ... I rarely use my garage bench anymore. :D

I bought a comfortable office chair and move both wherever in the house I want to size/reload now.

Shimitup
October 5, 2010, 03:05 AM
That sounds like a delightful way to spend your time and I wish you a speedy recovery.

ArchAngelCD
October 5, 2010, 05:06 AM
JP,
It sounds like a great way to convalesce and spend your time. I spend a lot of time on my back porch and never thought of moving my reloading efforts out there. I just might have to give it a try...

Get well soon.

Eagle103
October 5, 2010, 10:19 AM
What a great story! I can only hope to have your passion 40 years from now! Godspeed your recovery!

loadedround
October 5, 2010, 10:26 AM
Jamesicus:
I can't offer you any suggestions since you seem to have the reloading procedure down pat. However I would like to offer you my best wishes for a speedy and complete recovery and that you're back out in the field or range very soon. God bless! :)
Mike/Loadedround

moxie
October 5, 2010, 10:28 AM
Jamesicus, You're an inspiration! God bless you and I pray for a speedy recovery.

Kernel
October 5, 2010, 10:44 AM
JP, do you find that a crimp is unnecessary, when shooting light recoiling Trail Boss loads? Some say a firm crimp helps with uniforming the powder burn, and therefore creating better accuracy, with light loads. What has been your experience with crimps, light loads, and Trail Boss? How about low recoiling .30-06 loads with other powders? What kind of groups are you getting with your Trail Boss loads?

jamesicus
October 5, 2010, 11:17 AM
Kernel wrote:
JP, do you find that a crimp is unnecessary, when shooting light recoiling Trail Boss loads? Some say a firm crimp helps with uniforming the powder burn, and therefore creating better accuracy, with light loads. What has been your experience with crimps, light loads, and Trail Boss? How about low recoiling .30-06 loads with other powders? What kind of groups are you getting with your Trail Boss loads?
My experience with Trail Boss reduced loads is that crimping is really not necessary and does not appear to me to effect accuracy, Kernel. I only use Trail Boss for reduced loads. Here are a few recent target groupings I have shot using Trail Boss reduced loads:


http://jp29.org/rifle04.JPG

http://jp29.org/rifle15.JPG

http://jp29.org/rifle17.JPG

http://jp29.org/rifle20.JPG

http://jp29.org/lott23.JPG


All were shot at a 50 yard covered rifle range from a bench using a Caldwell rifle rest. The first four targets were shot using my CZ 550 American caliber 30/06 bolt action rifle equipped with a 3-9x variable power scope - cartridge loading was as I describe in this thread. The last target was shot using my CZ 550 American caliber .458 Lott bolt action rifle equipped with a Nikon 1x scope - 500 grain Hornady solid bullets and 20 grains of Trail Boss.

JP

Kernel
October 5, 2010, 11:48 AM
JP, those groups look great. You say you may never hunt again, but with those loads, it looks to me, like you would have a very effective load for small game and nuance animals - rabbits, squirrels, crows, grackles, pigeons, and such.

jamesicus
October 5, 2010, 11:54 AM
Thank you - Shimtop, ArchAngelCD, Eagle03, loadedround, Moxie - for your kind words and well wishes. I will post photos of my reloading set-up later today.

JP

420Stainless
October 5, 2010, 04:49 PM
Good to hear you're enjoying the hand press. I actually do most of my loading with a hand press as well just to avoid the temperature extremes in the garage.

I'm glad your able to reload during your recovery and wish you a full recovery.

I had bypass surgery 4 weeks ago and now have all the time in the world to reload, but was told by the doctor to avoid pushing or pulling hard or repetitively on anything for a couple months:(. By the time I get cleared to use a press I'll be back to work and won't have the time. Great to be alive and headed toward recovery though.

Thanks for your inspiring words.

jamesicus
October 5, 2010, 05:26 PM
420Stainless wrote:
Good to hear you're enjoying the hand press. I actually do most of my loading with a hand press as well just to avoid the temperature extremes in the garage.

I'm glad your able to reload during your recovery and wish you a full recovery.

I had bypass surgery 4 weeks ago and now have all the time in the world to reload, but was told by the doctor to avoid pushing or pulling hard or repetitively on anything for a couple months. By the time I get cleared to use a press I'll be back to work and won't have the time. Great to be alive and headed toward recovery though.

Thanks for your inspiring words.

Thank you, 420Stainless - I wish you a speedy and complete recovery. Actually the only hard pushing/pulling I have experienced was when I was attempting to fully seat Remington 9 1/2 primers using my RCBS hand priming tool - I simply don't have the hand strength to do that without a real struggle. A switch to CCI primers solved that problem though. I found that neck resizing 30/06 cartridges using the Lee hand press required very little effort on my part.

James

jamesicus
October 5, 2010, 07:14 PM
Earlier, I wrote:
.......... I will post photos of my reloading set-up later today.

http://jp29.org/reload01.JPG
All equipment (except rifle) fits in easily transportable plastic storage bin

http://jp29.org/reload02.JPG
Rifle with firing pin mechanism removed - for checking chambering and bolt closure

http://jp29.org/reload03.JPG
Pretty much all equipment and components (dial caliper missing) laid out on table top

http://jp29.org/reload04.JPG
Case (brass) prep equipment (including RCBS collet bullet puller - just in case)

http://jp29.org/reload05.JPG
RCBS 30/06 Neck Sizer die set with virgin cartridge case and test dummies

http://jp29.org/reload06.JPG
Lee hand press set up for neck re-sizing and (primer) de-capping

http://jp29.org/reload07.JPG
Set-up for Trail Boss powder charging using Lee dipper

http://jp29.org/reload08.JPG
Lee hand press set up for bullet seating


I actually set-up this reloading operation at various locations around the house (Kitchen table, in my den, etc.) although my primary location is on the front patio table.

Walkalong
October 5, 2010, 07:29 PM
Way to hang in there and stay positive jamesicus.

As to your Sig line, my 85 year old mom tells me exactly the same thing all the time. "This growing old ain't for sissies you know". Since she is getting "forgetful", I hear it often. :)

Great pics by the way. Here's to a speedy recovery. AC

jamesicus
October 5, 2010, 09:07 PM
Thank you for the kind words and thoughts, Walkalong - and please give my regards to your young at heart mother!

James

bds
October 5, 2010, 09:38 PM
jamesicus, when I grow up in my 80s, I hope to be shooting and reloading - nice clean setup and pictures. Get well soon!

That yellow Tupperware container sure brings back memories of taking stew for lunch at school. :D

Blackrock
October 5, 2010, 11:36 PM
I was 57 when I had Prostate Cancer surgery. Went home with a catheter for three weeks.
Got bored by the 3rd day and went out to the shop and started prepping some brass. I had my pee bag hung on a nail down low on the bench. My wife came looking for me and told me I sure didn't need any more special treatment if I could reload out in the shop.
So hang in there James and enjoy all ya can as long as ya can.

jamesicus
October 6, 2010, 12:46 AM
Blackrock wrote:
I was 57 when I had Prostate Cancer surgery ..........
I was seventy when I had my terps and they found cancer cells, Blackrock - but everything has been fine for me on that front so far. Like you I did not find the "pee bag" too confining - here's wishing you long life and lots more reloading!
.......... So hang in there James and enjoy all ya can as long as ya can.
Thank you for the well wishes, Blackrock.

James

jamesicus
October 6, 2010, 12:48 AM
Thank you for the well wishes, bds.

James

Oyeboten
October 6, 2010, 04:25 AM
Hi jamesicus,


Really nice economical easy to move aruond Re-Loading set you you put together.


Tell us about the Rifle?


It's a .30-'06...and...?


I have heard a lot of good tings about Trailboss for lighter Rifle Loadings, looks like your Targets bear this out.

ArchAngelCD
October 6, 2010, 04:39 AM
That looks like a great setup JP. I think you're right, all your stuff is easily transported in that plastic bin.

I have one suggestion, I would substitute Imperial Sizing Wax (http://www.midwayusa.com/viewproduct/?productnumber=519525) in place of the Lee case lube. Imperial Sizing Wax is extremely slippery, you use very little so it lasts forever and it's water soluble. I usually just wipe it off with an old terrycloth rag. Considering you are using a handloader to re-size the additional lube will make the job easier.

doubleh
October 6, 2010, 10:34 AM
Hello, jamesicus. I am glad you are recovering well and able to be doing things you enjoy. You are an inspiration to me. I'm eight years your junior and have given up shooting anything with the recoil of my '06's. I have been playing with .223's and a 22/250 but enjoying the 22/250 a lot less than the .223's. Ol' Arthur has done a number on my right shoulder along with most of my other joints and recoil really hurts. I may try some of the reduced loads just to shoot the '06's again.

That is a handy looking setup for reloading on the patio. I won't be doing any reloading on my patio though. Dang wind blows all the time. I do some blackpowder revolver shooting and the wind is such a problem that I pre- measure my powder charges before going to the range.

jamesicus
October 6, 2010, 10:59 AM
Hi jamesicus,


Really nice economical easy to move aruond Re-Loading set you you put together.


Tell us about the Rifle?


It's a .30-'06...and...?


I have heard a lot of good tings about Trailboss for lighter Rifle Loadings, looks like your Targets bear this out.
Thanks, Oyeboten. About the rifle: it is one of best 30/06 bolt rifles I have owned - and I have owned many. Rather than try and extoll the virtues of the CZ 550 myself, let me refer you to this (part 1 and 2) article:

http://www.realguns.com/Commentary/comar158.htm
http://www.realguns.com/Commentary/comar159.htm

James

jamesicus
October 6, 2010, 11:10 AM
That looks like a great setup JP. I think you're right, all your stuff is easily transported in that plastic bin.

I have one suggestion, I would substitute Imperial Sizing Wax (http://www.midwayusa.com/viewproduct/?productnumber=519525) in place of the Lee case lube. Imperial Sizing Wax is extremely slippery, you use very little so it lasts forever and it's water soluble. I usually just wipe it off with an old terrycloth rag. Considering you are using a handloader to re-size the additional lube will make the job easier.
Thanks, ArchAngelCD. I will take up your suggestion for I have never used Imperial Sizing Wax (I have used the Lee lube for many years). I do not lubricate the outside case neck when Neck Sizing, and have been pleasantly surprised at how easy the operation is using the Lee Hand Press. It will be a real bonus if the Imperial Sizing Wax makes it easier yet!

James

jamesicus
October 6, 2010, 11:19 AM
Hello, jamesicus. I am glad you are recovering well and able to be doing things you enjoy. You are an inspiration to me. I'm eight years your junior and have given up shooting anything with the recoil of my '06's. I have been playing with .223's and a 22/250 but enjoying the 22/250 a lot less than the .223's. Ol' Arthur has done a number on my right shoulder along with most of my other joints and recoil really hurts. I may try some of the reduced loads just to shoot the '06's again ...........
Thanks, doubleh. Please do try Trail Boss for your 30/06 rifles - I think you will be enormously impressed by the very light recoil and much reduced muzzle blast.

Trail Boss References:
http://www.handloads.com/articles/default.asp?id=37
http://www.imrpowder.com/PDF/Trail-Boss-data.pdf

James

jamesicus
October 6, 2010, 01:07 PM
Attesting to the accuracy potential of reduced load Trail Boss powder:

Shot by me using a CZ 550 American bolt action rifle - 30/06 caliber.

Shooting from covered rifle range bench at 50 yards under calm conditions - 90 F temperature (10 am) - bright sunshine - Caldwell rifle rest. Bullet velocity measured using a ProChrono chronograph positioned 15 feet from the rifle barrel muzzle: Twenty shot string result: 1518 fps average.

Hodgdon IMR "Trail Boss" powder (15 grains) - Winchester brass (neck sized) - Hornady .30 cal 150 gr FMJ/BT bullets (seated to cannelure, not crimped) -
CCI 200 large rifle primers.

http://jp29.org/rifle24.JPG
Twenty shot string

http://jp29.org/rifle25.JPG
Five shot string

James

If you enjoyed reading about "Reloading with a little disability" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!