model 65


PDA






icanthitabarn
February 22, 2012, 04:41 PM
I had butted in on another thread, but here is my own. I have looked a few times at this S+W. Model 65 S.S. It has a stamp of 65-2, on the crane. The gun is not pinned or recessed. The other numbers, also on the crane, are obviously re-stamped with a totally different number. Is this common? It's a Frankengun I guess

If you enjoyed reading about "model 65" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
dprice3844444
February 22, 2012, 04:50 PM
nope,inspection marks

rcmodel
February 22, 2012, 05:12 PM
The actual serial number is stamped on the butt.

The odd numbers & stamps inside the crane cut are assembly numbers and fitters marks used during manufacturing to keep the crane, cylinder, sideplate and frame together during final fitting and polishing after they had been fitted to each other.

It's not a Frankengun.

rc

icanthitabarn
February 22, 2012, 05:14 PM
Maybe I was not clear. I know the inspection mark, isn't going to match the model number. The inspection mark is re-stamped completely different from original inspection mark. I was told by a very smart poster that a 65-2 should be pinned and recessed.

bk42261
February 22, 2012, 05:16 PM
Are you sore it says 65-2? I just checked my wife's 65-2 and it is, indeed, pinned and recessed.

rcmodel
February 22, 2012, 05:19 PM
That is correct.
A 65-2 should be P&R.
The 65-3 change in 1982 eliminated the pinned & recessed.

rc

icanthitabarn
February 22, 2012, 05:25 PM
The gun is not pinned or recessed and is stamped 65-2 no question.

rcmodel
February 22, 2012, 05:35 PM
Probably just an early 65-3 that got stamped wrong.

Stranger things have happened.

rc

earplug
February 22, 2012, 08:47 PM
I have a M-65-5 and it has the spring loaded yoke srew and plunger.

Curious if your revolver has this?

icanthitabarn
February 23, 2012, 12:46 AM
A wrong model stamp and a new set of codes stamped over an existing set of codes?

cyclopsshooter
February 23, 2012, 01:24 AM
I have a 65-2 3" from 1982 that is recessed, NOT pinned, and with a large side-plate logo. You may very well have something similar, curious to know the date of manufacture.

PabloJ
February 23, 2012, 02:24 AM
The steel K-framed .357 S&W is perfect example of form following function or is it the other way around? A kinda revolverfection if you will.....

easyrider6042004@yahoo.ca
February 23, 2012, 05:37 PM
Got a 65-2. It is indeed P & R.

PabloJ said:
A kinda revolverfection if you will.....

I agree:D

Tinman357
February 25, 2012, 03:58 PM
I would love to get my hands on a good 3in model 65.

dprice3844444
February 25, 2012, 04:28 PM
tin,keep checking gunbroker,they show up there.the 3 inch is sweet.had one of those ss 64's bobtailed for the tampa sheriff's office way back in the 80's.shoulda never soldit.it was part of a custum order.if you do find one,you can have a slot milled where the front sight goes so you can put a tritium sight in it

surfinUSA
February 25, 2012, 11:09 PM
Don't worry that it's not P&R. at the time of the change its possible to find pinned gun w/o recessed cylinders and guns with recessed cylinders that don't have pinned barrels.

S&W-Keeper
February 26, 2012, 11:54 AM
It was probably at he end of the -2 run. It is not uncomon.

SwampWolf
March 15, 2012, 06:06 PM
As an aside, are any/all Model 65 LadySmiths pinned and/or recessed?

If you enjoyed reading about "model 65" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!