Homemade auto drive for 366


March 29, 2012, 10:37 AM
Last. Nights run of 500 shells played a toll on my Arm and was wondering how hard it would be to make a hydro unit as I have acces to pumps valves cylinders and hoses.. What about an electric unit

If you enjoyed reading about "Homemade auto drive for 366" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
March 29, 2012, 10:59 AM
No help here.
Perhaps do 1-200 at a time 'til your arm/body builds up/back up if at all possible?

March 29, 2012, 02:46 PM
Easy, if you copy others. These guys make them for lots of loaders including the 366.



David Wile
March 29, 2012, 08:47 PM
Hey Broken,

I have never used any press with any sort of powered cycling, so I may be missing the barn by 12 yards on this. First, the title of your thread mentions an auto drive for a 366, and I am assuming you are talking about the Pacific/Hornady 366 progressive shotshell presses. I have a Pacific 366 in 20 guage, and two Hornady 366 presses: one 16 guage and one 12 guage. Prior to my 366s, I had a few of the earlier generation Pacific progressives, and I have a deep appreciation for the evolution to the 366 presses.

In my experience with all of my progressive presses, I have never felt the operating cycle would lend itself to any automatic drive mechanism. There are just too many cycles where I "feel" something happening that requires me to hold the handle in place while I check things out to make sure things are going correctly. One for example would be the one brand of plastic wad that uses eight small petals rather than the more common wads with four petals. The four petal wads rarely get hung up in the reloading cycle, but the eight petal wads frequently have a petal get out of place, and I have to hold the handle in place while I free the offending petal. If an automatic drive system were in place, the errant wad petal would be stuffed in without any chance for me to "feel" the difference.

Like Deaf mentioned, if 500 shells at a time is too many, cut it down to two 250 shell sessions or even five 100 shell sessions. I am old and beat up with arthritis in my joints, but a 500 round session on a 366 does not bother me so far (knock on wood). If 500 rounds did bother my joints but I could do a 100 round session with no complaints, I like reloading enough to switch to doing five 100 round sessions.

I really do enjoy the time I spend reloading, and I do not look at it as a necessary evil just so I can go shooting. I hope you are able to work out your difficulties and enjoy your reloading as much as I.

Best wishes,
Dave Wile

March 29, 2012, 09:00 PM
Simpler solutions abound.

► First I'd try adapting an offset handle, like the unit Dillon offers. The larger bearing area and the more natural position of the L-shaped handle get rave reviews from users in your condition. Many people make these, or your local weld shop may have a piece of scrap.


► If that doesn't offer enough power, then connecting a rod to a foot operated "pedal" might offer some solution. Your legs have tremendous muscles compared to the arms.

The point is, going with air, vacuum, hydraulic or electric is going to require safety switches and an emergency stop to keep the automatic sequence in check. And the safety system may cost as much as the drive system once all the interlocks and overrides are installed.

Just a suggestion.

March 30, 2012, 08:46 AM
you guys have a good point! would a shovel type handle help out?

March 30, 2012, 09:14 AM
Shovel handles were the standard option for Ponsness-Warren shot shell reloaders for years. Now it looks like they've gone with the cheaper L-shaped handle. You can order one of those direct from them at: http://www.reloaders.com .



March 30, 2012, 08:41 PM
Check out this ad on Ebay. The guy is selling shovel handles you adapt to your existing press handle. Item # 270942648273 .


March 31, 2012, 12:09 AM
thanks guys!

If you enjoyed reading about "Homemade auto drive for 366" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!