Course, you can buy a real variable speed bench top drill press with no wobble in it for not much more.
April 23, 2012, 09:02 PM
Thanks for the links. I wish I had more woodworking experience and I'd buy something nice
April 23, 2012, 09:13 PM
I had one of the 1/4" drill holder drill presses many years ago.
It was pretty funky and had so much slop in the joints the drill could move all over.
I think I could use my calibrated eyeball and hand hold a drill straighter in one place.
See this instruction & the vid about hand roll crimping with a drill.
April 23, 2012, 10:03 PM
The crimp I bought was a BPI and I did read that article. I might need to be more patient. Tx
April 23, 2012, 10:25 PM
I roll crimp all of my shotgun loads from 12 ga bird shot, slugs,steel shot, etc, all the way down to 410 loads. I also bought a BPI roll crimper and I can honestly say they are crap compared to the Prescision Reloading roll crimpers. I am refering to their metal ones. I use a hand drill in reverse and get perfect crimps almost every time. There was no learning curve with them. The BPI almost flattened the crimp and was not much good on slugs, whereas the PR models work on everything.
I agree the BPI roll crimpers are junk. The reason is the roll pin they use instead of the 4 bumps in the lyman. Roll crimping requires a lot of heat to form the crimp. It's hard to hold the base of a shell while putting pressure on the crimper/drill. The BPI hull vise is worth it's weight in gold! The downward pressure MUST be perfectly square with the mouth of the hull. If it's not, you'll get crooked crimps.
Oh, you should be using new cases, or longer cases with the star crimp cut off.
April 24, 2012, 09:39 PM
The PR crimper also uses 4 bumps instead of pins. Does the Lyman need to spin backwards like the PRs?
April 25, 2012, 03:38 AM
The "new and improved" BPI roll crimpers have 2 wheels in them and work much better FYI.
April 28, 2012, 08:47 PM
Well I crimped 23 today. Just don't have the knack for even downward pressure but they all looked ok
April 29, 2012, 08:05 AM
If you do not have the knack for even downward pressure by hand I would still seriously think about getting an inexpensive drill press. Look on Craigs list or a local swap and sell forum/paper for a used one. Seems like everything is for sale these days.:scrutiny:
April 29, 2012, 11:13 PM
I have been thinking. Just trying not to "fill up" my bench with thing I won't use a ton. I'll keep looking. Thx.
April 29, 2012, 11:15 PM
What is in those? Don't look like slugs to me?
September 28, 2012, 01:17 AM
Bought this drill and it is the perfect size but I don't think it has the torque to do the job. Figures.
I think that I paid about that for a 1/3 HP table type from Harbor Freight about 3 years ago. Just saying. Yeah the prices have gone up but not THAT much more.:scrutiny:
September 28, 2012, 09:27 AM
I saw a harbor freight for anout $10 more but was quite bigger. I was hoping the smaller footprint would still do the job. Afraid I was wrong
September 28, 2012, 06:48 PM
There used to be a smallish drill press frame that I think Sears sold. You just added your hand drill and went for it. I even see some used at times. The whole thing would fit in a shoe box without the drill attached---this might be what you seek. If I can find a linky I will edit this.:)
Try Skil 45140 drill stand. or try googling hand drill stand
September 29, 2012, 01:10 AM
Thanks. Now I need to figure out what to do with the one I bought. I'm sure the restock fee is outrageous. :)
September 29, 2012, 09:12 AM
I've got two or three of these type laying around in the shop...