Ruger Security Six boot grip?


PDA






plateshooter
September 23, 2012, 07:11 AM
I have a 2.75" Security Six and am looking for a "boot" type grip for it. I have the stock grips, and the "Pachmier (sp)" rubber grips, and the Ruger full size target grips. I am looking for something that still gives a good grip but is easier to use for ccw.

Any suggestions would be appreciated.

If you enjoyed reading about "Ruger Security Six boot grip?" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
mavracer
September 23, 2012, 09:11 AM
Call Badger he doesn't list them on his site but does still make a few. I just got these for my Speed Six.
http://i266.photobucket.com/albums/ii261/mavracer/IMG-20120319-00417640x480.jpg

Deaf Smith
September 23, 2012, 05:28 PM
Eagle used to make the 'Secret Service" line for the Speed Six.

http://www.thehighroad.org/attachment.php?attachmentid=129168&d=1287341282

Yep they are mine above. I don't think Eagle makes them now but they should!

Failing that, Badger.

Deaf

plateshooter
September 24, 2012, 06:19 AM
Thanks for the suggestions. I will check them out.

WoodchuckAssassin
September 24, 2012, 08:02 AM
I loooooove those boot grips! I plan on getting a set put on my old 686 no-dash. I was going to go through Badger, also.

Deaf Smith
September 25, 2012, 08:30 PM
http://www.thehighroad.org/attachment.php?attachmentid=168798&d=1343179435

Secret Service stocks on my 2.5 inch 686 (among others!)

Deaf

Confederate
September 25, 2012, 10:45 PM
It's not too difficult to change the square grips to round butt grips. You can also use a Tyler T-Grip Adapter, which would be my first choice. But I also like the round butt for guns up to 4-inch barrels.

http://i256.photobucket.com/albums/hh198/jriler/RugerSecurity-SixSm.jpg

Ruger with a T-grip adapter.



http://i256.photobucket.com/albums/hh198/jriler/Bench_1.jpg

http://i256.photobucket.com/albums/hh198/jriler/Bench_2.jpg

http://i256.photobucket.com/albums/hh198/jriler/Bench_3.jpg

http://i256.photobucket.com/albums/hh198/jriler/RugerSecurity-SixTrio_2.jpg

The two bottom pistols have round butt grips that feel great. I wouldn't
put round grips on a 6-incher, though.

mesinge2
September 25, 2012, 10:49 PM
Thanks, mavracer!!

I didn't know those existed. I will so be ordering a set for my 2.75" Speed Six.

Deaf Smith
September 25, 2012, 11:02 PM
Confederate,

I did that to my 4 inch blued Security Six just this weekend. Bench grinder and used old RB Speed Six grips to scribe against. Then polished and cold blued before putting on pachmayr RB grips like you have pictured.

Also, of course, I did that a while ago to my 2 3/4 Stainless Six.

http://www.thehighroad.org/attachment.php?attachmentid=129168&d=1287341282

But it's just to pretty to shoot!

Deaf

mavracer
September 25, 2012, 11:50 PM
I loooooove those boot grips! I plan on getting a set put on my old 686 no-dash. I was going to go through Badger, also.
Yes they look good on Smiths too
http://i266.photobucket.com/albums/ii261/mavracer/IMG-20120114-00213.jpg
for that matter they look good on Colts too
http://i266.photobucket.com/albums/ii261/mavracer/IMG-20120319-00419640x480.jpg

If you enjoyed reading about "Ruger Security Six boot grip?" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!