Chip McCormic 10 rd 1911 Mags


PDA






ExAgoradzo
November 18, 2012, 01:32 AM
Is there any reason why this isn't a great idea???

Thanks,
Greg

If you enjoyed reading about "Chip McCormic 10 rd 1911 Mags" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
bainter1212
November 18, 2012, 01:36 AM
In my experience, the reliability of mags goes down in proportion to the amount of extra rds they try to get you to squeeze in. The 8 rounders seem to work ok but I have had issues with the "trick" higher capacity mags.

ShadowsEye
November 18, 2012, 03:06 AM
Also you have to be ok with a non-flush fitting mag, the 8 rounders barely hang out, 10 round sticks definitely will.

bigfatdave
November 18, 2012, 03:26 AM
you can also ram them in too far if you're too enthusiastic - some have a shelf to act as a spacer in a .gov size frame, much like slamming a .gov size mag into an officer frame

Batty67
November 18, 2012, 09:21 AM
I have two for my Marlin Camp 45. Also have a Wilson Combat 10-rounder. Both function quite well. But then again, I'm using them in a carbine, not a pistol.

joecil
November 18, 2012, 09:26 AM
I've had a number of the Chip McCormic mags in 7, 8 and 10 round all worked fine with my Springfield and RIA 1911. Both of these guns however have steel frames and have seen some complaints about one of the magazines being used in alloy framed guns marking the feed ramps.

1KPerDay
November 19, 2012, 12:41 PM
They have worked fine for me. YMMV.

Fishbed77
November 19, 2012, 05:01 PM
I can't speak to the 10-rounders, but the 8-round Chip McCormick Power Mags have been 100% reliable in my Colt Government XSE.

ExAgoradzo
November 19, 2012, 06:42 PM
Appreciate the input guys!

shafter
November 19, 2012, 08:10 PM
I prefer 8 round magazines that are flush with the bottom of the grip. 8+1 is plenty of ammunition for me. If I want more I'll get a Glock.

7.62 Nato
November 19, 2012, 08:51 PM
I carry the 8 rd in the gun and the 10 rd for backup. Never had any trouble with them.

AZ PAUL
November 19, 2012, 08:57 PM
I used 10 round mags for a long while including on-duty. They were always 100 percent.

Jaymo
November 19, 2012, 09:28 PM
No experience with the tens, but the eight rounders have been completely reliable in my ATI.

Simmy952
November 19, 2012, 09:40 PM
I have several of the 10rd mags. Have not any issues with them. If extra capacity is needed, they work well.

Arp32
November 19, 2012, 10:02 PM
I have one 10-rounder for my government model, it functions perfectly fine but I feel like it throws off the balance of the gun when fully loaded.

USAFret
November 19, 2012, 11:11 PM
Have always heard good things about the Chip McM mags but the one that I bought just doesn't work in my RI 1911. First round fires and the mag disengages. Slap it back again and the next round fires but the mag drops again. Tried different ammo types and the same thing happens. Just doesn't work except to make my 1911 a single shot gun. Not good.

jmr40
November 20, 2012, 08:18 AM
I have several 8 rounder's and 1 10 round mag. All have been 100%. I wouldn't carry the 10 round mag, but it is in a gun that says at home.

Hk Dan
November 20, 2012, 10:28 AM
Well, Hell, they've been using them in USPSA L10 since the division started. They ae fine, and completely reliable. If McComicks 7 or 8 round mags work with your gun these should too.

tuj
November 20, 2012, 01:54 PM
I use Tripp Cobramags, both 7 and 10 rounders. The 10 are obviously not flush-fit, but the reliability is outstanding with both the 7 and 10.

If you enjoyed reading about "Chip McCormic 10 rd 1911 Mags" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!