45 acp too hot?


PDA






badnova
November 19, 2012, 11:35 PM
I found a load for 45 acp with 9gr. of unique with a 200 jhp bullet
Is this too hot?

If you enjoyed reading about "45 acp too hot?" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
chris in va
November 19, 2012, 11:38 PM
Probably should be in the reloading section, but my lyman manual shows a 200gr SWC as 7.5gr MAX.

A 200 JHP is 6.5gr MAX. Don't load that 9gr load, it'll probably blow up your gun!

Steve C
November 20, 2012, 12:04 AM
9.0 grs of Unique behind a 200gr JHP in the .45 ACP is definitely above the max load levels in published data by the powder and bullet manufacturers for at least the last 40 years I've been reloading. Now it may be a load for the "super" or a +P load or something published in a non scientific tested source.

The dirty little secret on hand loading the .45 acp is it can be overloaded without danger of a KB if good or new brass is used however firing it in the regular 1911 will soon ruin the gun with the excess slamming and battering of hot loads. I once met a fellow years ago that loaded 10 grains of Unique behind the old Speer 200gr JHP. His comment was that they shot flat compared to regular loads. Never did run into him again to see how his guns where holding up to the load. He was a Longshoreman and made lots of money so it wasn't much of an issue for him financially to replace a ruined gun every year. Persoanlly I just wrote him off as being kind of reckless.

C0untZer0
November 20, 2012, 12:13 AM
Test it in an HK Mark 23 :D

1911Tuner
November 20, 2012, 07:54 AM
Yeah. I'd say that's a bit much.

ku4hx
November 20, 2012, 08:02 AM
Yep, way too hot. You need to get some loading manuals and build up to max loads. There are online sources too.

Lyman's 3rd edition "Pistol & Revolver Handbook" shows 6.5 grains Unique as max with a 200 grain JHP on page 190.

forindooruseonly
November 20, 2012, 08:35 AM
I found a load for 45 acp with 9gr. of unique with a 200 jhp bullet
Is this too hot?

Just out of curiosity, where did you find that load?

hentown
November 20, 2012, 08:40 AM
IF you can find any of Clark's data, you can probably find a load calling for 10.5gr! :evil:

mljdeckard
November 20, 2012, 09:23 AM
I have found 5.5-6 grains to be plenty. They're your fingers.

Robert101
November 20, 2012, 01:44 PM
BadNova, that load seems to hot according to my data. Don't let that load go Super Nova on you and you'll have to change your "handle".

tuj
November 20, 2012, 01:53 PM
way too hot!

Hungry1
November 20, 2012, 06:57 PM
Yea, that's hot.

My Speer manual has 7.3 of Unique listed as max for a 200gr GDHP.

I've shot that load with 200 gr Hornady XTPs. Recoil is stout, but it very accurate.

Good Luck

Clark
November 20, 2012, 10:17 PM
When I worked up a 460 Rowland load in May 2000 in 20 ounce Patriot pistol and 185 gr bullets, I started out with Unique.

There is plenty of room in the 45acp case to get into trouble with Unique.

The brass can take it.
The chamber walls can take.
It is a matter of case support and recoil.
If the recoil springs are stiff enough, the chamber will come up empty.
The stiff springs accelerate the slide past the magazine so fast the next round does not have time to come up.
Double up on the magazine springs to push up the next round faster, and it hurts the thumb to load a magazine.
And still the slide can be slamming into the frame.
That is not good for the frame, the slide, the shooter's hand joints, or nerves.

I believe that if the empty cases are landing 5 feet from the shooter and there are no case bulges, that is a good load.
Hot enough to feed reliably, and cool enough not to have slide slam. Not so much pressure as to cause a case bulge.

243winxb
November 21, 2012, 08:28 AM
Steve's pages lists 8.3gr as the highest. http://www.stevespages.com/page8a.htm

vegasbillsliv
November 21, 2012, 12:49 PM
Instead of 5.4 grains under a 230 grain lrn, I put 9 grains in. I was shooting over a chronograph. Shot one and immediately noticed the recoil and report. The chrony was showing 4 digits. I thought it was a fluke so I shot again. No fluke. The Kimber held up ok. The brass held up ok, just flattened primers. But I know pushing things 50% beyond the limit ain't good. I went back and looked at the scale and realized my mistake. I consider myself lucky.

accrhodes
November 21, 2012, 03:05 PM
mljdeckard - You run 5.5-6.0 grains in your 1911 with a 200 grain bullet? My 1911 wont even cycle with that low of a charge. I had to hit 6.2 grains before mine would even cycle the next round. I found the best shooting out of my Springfield to be 6.6 grains.

To the OP - That is way too hot of a load. It's hardly worth the risk.

grumpy66
November 21, 2012, 03:29 PM
9 grains of Unique is what I load in my .45colt.

6 grains is a good load for a .45acp.

dnite
November 21, 2012, 03:53 PM
A TRUE story not a cowboy tale

Bought a beautilful used SS Colt officers model, took it to the range with white box Winchester 230 grain.

The third round broke the dust cover off the slide in front ofthe frame and out came the spring and guide rod.

Boy was I sick..... Sent the pistol and parts to Colt who told me the pistol had been abused by hot loads, peening on the barrel lugs etc.

Someone prior to me had sadly abused this pistol.

I load 5.5 to 6 grains Unique or 4.5 of Bullseye under a 230 grain with no problems and that makes a nice shooting round.

Colt fixed the pistol and it was an expensive but cheap lesson at the same time.

dnite

If you enjoyed reading about "45 acp too hot?" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!