Quickload Results Please 30-30 110gr HP & N120


PDA






Eb1
January 23, 2013, 01:30 AM
I would like to use some of my stock pile of VV N120 for the 30-30 using the Speer 110 gr HP and VV N120 with a Rem 9 1/2 primer. Mix of brass Rem and Win.

Could someone with Quickload run a formula for me if you don't mind? I know that N120 is near IMR 4198 and RL7. I would just like to see what QL says about that combo.

Thank you.

If you enjoyed reading about "Quickload Results Please 30-30 110gr HP & N120" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
Eb1
June 26, 2013, 04:44 AM
I am still interested in this data if someone would be so kinds.

Load information using Quick Load for:

30-30 Winchester
Winchester/R-P Brass
CCI/Win/Rem Primers
Speer 110 Semi-Jacketed HP
Vihtavuori N-120

I didn't want to just bump this thread, but I would like to add more info if needed. I have worked up a load with this powder using the 125 Grain Sierra FNHP moving at 2150 fps for short distance deer out of a 30-30 using a red dot. Works awesome!
I also have data with the 125 Grain Sierra FNHP @ 2500 fps with VV-N120. Just need to get that 110 Grain Semi-Jacketed HP moving. I have used H335, but didn't get good results. I know there is data for RL7 and this bullet. VV-N120 is close to RL7.

steve4102
June 26, 2013, 05:57 AM
Barrel Length and OAL?

Cartridge : .30-30 Win. (SAAMI)
Bullet : .308, 110, Speer HP 1835
Cartridge O.A.L. L6: 2.550 inch or 64.77 mm
Barrel Length : 22.0 inch or 558.8 mm
Powder : Vihtavuori N120

Predicted data by increasing and decreasing the given charge,
incremented in steps of 2.0% of nominal charge.
CAUTION: Figures exceed maximum and minimum recommended loads !

Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time
% % Grains fps ft.lbs psi psi % ms

-20.0 68 24.00 2119 1097 20555 4244 94.5 1.426
-18.0 69 24.60 2164 1143 21701 4356 95.4 1.397
-16.0 71 25.20 2208 1191 22907 4463 96.2 1.368
-14.0 73 25.80 2252 1239 24178 4566 97.0 1.341
-12.0 75 26.40 2296 1287 25517 4663 97.6 1.314
-10.0 76 27.00 2339 1336 26927 4754 98.2 1.288
-08.0 78 27.60 2382 1385 28413 4840 98.7 1.262
-06.0 80 28.20 2424 1435 29976 4920 99.1 1.238
-04.0 81 28.80 2466 1485 31618 4993 99.4 1.214
-02.0 83 29.40 2507 1536 33326 5060 99.7 1.190
+00.0 85 30.00 2548 1586 35104 5121 99.9 1.168
+02.0 86 30.60 2589 1637 36965 5174 100.0 1.145 ! Near Maximum !
+04.0 88 31.20 2629 1688 38918 5220 100.0 1.120 ! Near Maximum !
+06.0 90 31.80 2668 1739 40965 5264 100.0 1.096 ! Near Maximum !
+08.0 92 32.40 2707 1790 43113 5306 100.0 1.072 !DANGEROUS LOAD-DO NOT USE!
+10.0 93 33.00 2745 1840 45365 5347 100.0 1.050 !DANGEROUS LOAD-DO NOT USE!

Results caused by 10% powder lot-to-lot burning rate variation using nominal charge
Data for burning rate increased by 10% relative to nominal value:
+Ba 85 30.00 2643 1706 41594 4912 100.0 1.094 !DANGEROUS LOAD-DO NOT USE!
Data for burning rate decreased by 10% relative to nominal value:
-Ba 85 30.00 2411 1420 28743 5141 96.3 1.250

Eb1
June 26, 2013, 06:05 AM
Thank you.

I can give you that information.

Barrel Length: 20" Marlin 336
OAL: 2.415


Thank you again. I hope this refines your query.

If you enjoyed reading about "Quickload Results Please 30-30 110gr HP & N120" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!