40 cal powder


PDA






fetch
February 5, 2013, 01:22 AM
Just started loading 40 cal. I used what I had left of hp38 and need to get more powder tomorrow and I thought I would see what you guys prefer for 40. Will be shooting out of a glock 22. Bullets will be 155 to 180 gr

Thanks in advance

If you enjoyed reading about "40 cal powder" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
GLOOB
February 5, 2013, 01:25 AM
Melikes AutoComp for the full tilt stuff.

bds
February 5, 2013, 05:34 AM
Just started loading 40 cal ... glock 22 ... 155 to 180 gr

I shoot Glock 22/23/27 with factory and Lone Wolf/KKM aftermarket barrels.

For me, I used Universal/WSF/HS-6/AutoComp for higher velocity loads with 155/165/180 gr Montana Gold jacketed bullets. In general, with slower burning powders, you won't get optimal accuracy until high-to-max range load data.

For lower velocity/pressure target loads and 140/155/160/170/180 gr plated/lead bullets, I use faster burning W231/HP-38. With heavier 180 gr bullet, it will produce accuracy even at start charge. With lighter weight bullets, I need to push them harder but W231/HP-38 will produce accuracy at mid-to-high range load data. If you are looking for lighter recoil yet accurate target loads, 180 gr and start-to-mid W231/HP-38 will work well.

I don't suggest faster burning powder than W231/HP-38 for 40S&W as recoil gets snappy and makes shooting less comfortable. While Titegroup can produce accurate match loads, I do not suggest Titegroup to new reloaders and especially not for 40S&W as too many KaBooms and Glocks have been associated with it.

If you are using mixed range brass with unknown reload history and want lower pressure loads that are accurate, W231/HP-38 at mid-to-high range load data is hard to beat.

YMMV

FROGO207
February 5, 2013, 08:53 AM
I am loading Missouri Billet IDP #7 and HP-38/231 with great results. I also use a lot of 700-X, especially with the heavier jacketed bullets while I use far less of these. There are lots of good choices out there but I find that what works well with 45 ACP also works well in the .40. Just adjust the amount of propellant relative to the caliber/bullet used and the results will be good.

jack44
February 5, 2013, 09:49 AM
Power pistol & unique

TonyT
February 5, 2013, 10:37 AM
fetch,
For powder puff loads in 40 S&W at ca. 725-775 fps I use WST.
For full power loads I prefer WSF.

THe Dove
February 5, 2013, 01:59 PM
Titegroup for me.

The Dove

fetch
February 5, 2013, 05:08 PM
Thanks for all the info guys. I ended up sticking with hp38 for now.

eam3clm@att.net
February 5, 2013, 07:25 PM
Hp38 is a fine run of the mill 40s&w powder. It is forgiving to a point, and my go to powder for cast/plated bullets in most pistol calibers. Most of my plated are loaded with Acc#5 and unique. I also run alot of bullseye for plinking ammo.

J_McLeod
February 5, 2013, 07:31 PM
I use HP-38 in half my 40 loads and HS-6 in the rest.

kerreckt
February 5, 2013, 07:34 PM
I like Titegroup mostly and some Clays. HP-38 is too dirty.

AABEN
February 5, 2013, 07:45 PM
I like the 165 gr. I use Win 231 very clean powder 5.0 gr.

SDGlock23
February 5, 2013, 08:15 PM
For light up to normal (950 fps or less for 180gr) I like TiteGroup, HP38 and WST.

For more normal (950-1050 fps for 180gr) I like Unique, Power Pistol, AutoComp and WSF.

For higher power (1100+ 180gr) I like Longshot, Power Pistol, 800x (meters like crap) and VV 3N38 (good luck finding any).

If you enjoyed reading about "40 cal powder" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!