Perfect for me Mossberg...but ported. ?


PDA






wild cat mccane
February 8, 2013, 02:40 PM
Mossberg makes a 500 with the youth stock (Bantam) in 12 gauge. It has a 24" barrel and is ported.

I am not too keen on the porting and curious is 24" is a weird size. Any thoughts?

(home and just fun clay pigeon use)

If you enjoyed reading about "Perfect for me Mossberg...but ported. ?" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
rcmodel
February 8, 2013, 02:57 PM
I'm not seeing any mention of porting except in the fully rifled slug barrel.

http://www.mossberg.com/product/shotguns-pump-action-500-bantam-all-purpose/52132

http://www.mossberg.com/product/shotguns-pump-action-500-bantam-combo/54188

The shorter 24" barrel is in keeping with the shorter stock to keep the balance of the full size 500.

rc

wild cat mccane
February 8, 2013, 03:18 PM
same as this one?
http://www.impactguns.com/product.aspx?zpid=25745

I have read it is ported on other sites.

Bill.45
February 8, 2013, 03:49 PM
Does anyone know if the same pistol grip will fit the 20ga youth, or Bantam mdl., and the 12 ga ?

Deer_Freak
February 8, 2013, 07:27 PM
I have a 500 with ported barrels. If you shoot buckshot the ports will clog quickly. You can clean the ports when they are fouled with plastic using a pipe cleaner or small wire brush. You have to be careful if you lean against anything for brace. The ports will leave their mark on tree bark or painted surfaces. I can't say if they do anything or not. I have shot a pump all my life. Plus I am big fellow.

I can't answer your question about the pistol grip. If someone brings a pistol grip in my house I hope they have a buyer for it. They are not leaving a pistol grip here. I know I can not shoot a shotgun like a pistol or from the hip.

wild cat mccane
February 8, 2013, 08:55 PM
Assuming it is ported, are the ports in a place that would allow a gunsmith to cut the barrel to eliminate them and still have a good length?
Thanks!

rcmodel
February 8, 2013, 09:14 PM
Not unless you want to cut the choke tube threads off and have no choke.

Or pay $100 - $200 to have it re-threaded for choke tubes again.

rc

rule303
February 8, 2013, 10:43 PM
I have a couple of ported shotguns. I am not sold that the porting actually does anything, but I also don't find it to be a problem as long as you are wearing hearing protection. I personally would want the longest barrel you are comfortable with if you are going to shoot clays with it.

PonyKiller
February 9, 2013, 07:25 AM
with light loads i'm not sure it much matters, but with mag buckshot, mag goose loads it seems to for me, keeps the muzzle down, but i have a 28" barrel. My slug barrel is 24" and ported, i'm pretty convinced it helps there. It comes back so strait to the shoulder that i can see the sabots falling down range through the scope.

Virginian
February 9, 2013, 08:59 AM
I hate ports. So do a lot of my fellow hunters. On the range it doesn't matter. But you are not hunting in the blind or the field with any of our dogs. They do increase the noise considerably, especially for anyone or anything not directly behind the gun.

fxstchewy
February 9, 2013, 09:27 AM
I think King Obama shot a ported model in that photo op, works for him. :)

wild cat mccane
February 9, 2013, 04:13 PM
Kings don't get elected by majorities. Twice. :)


I am new to shotguns. Choke tube? What is this? (i know, so newbie).

Not planning on slugs...Do I want smooth?

Thanks for the help guys

rcmodel
February 9, 2013, 06:13 PM
Choke:

http://www.cheaperthandirt.com/MediaPages/ArticleDetail.aspx?mediaid=20

rc

wild cat mccane
February 9, 2013, 07:23 PM
thanks for the education

If you enjoyed reading about "Perfect for me Mossberg...but ported. ?" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!