Supressed 9mm with 158 gr SWC Leading?


PDA






Mudball_3
March 3, 2013, 01:44 PM
I am thinking about casting my own bullets in the future. I currently have a Beretta M9 with a AAC Ti-Rant suppressor. Will a hard cast boolit with a gas check work or will there still be too much leading in the supressor? Thanks much.

Anthony

If you enjoyed reading about "Supressed 9mm with 158 gr SWC Leading?" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
oneounceload
March 3, 2013, 02:28 PM
What load data are you using for a 38Spl bullet in a 9mm?

SharpsDressedMan
March 3, 2013, 02:32 PM
I thnk it is generally not recommended to used lead bullets, even with gas checks. You may retard the leading with a gas checked bullet, but you may also find the gas checks separating from the bullets due to the disrupted gases that will occur before the bullet exits the suppressor, and they may damage the suppressor if they do.

Mudball_3
March 3, 2013, 02:44 PM
oneounceload,

This (http://thefiringline.com/forums/showthread.php?t=439115) is were I am coming up with the load. It would have to be sized of course. 3 gr of Bullseye. That makes sense with the gas check.

rcmodel
March 3, 2013, 02:55 PM
The devil is in the details when reading reloading data.

You might notice the Lyman load is for a 158 Round-Nose bullet.
Not a semi-wadcutter.

I do not believe you can seat a 158 SWC short enough in a 9mm case to get it to miss the rifling and chamber.

The base of the bullet will go past the beginning of the case wall taper and bulge the case when seated short enough to chamber.
Then it won't chamber because of the bulged case.

You can with a round nose due to the round nose ogive missing the rifling at a longer OAL length.

rc

Mudball_3
March 3, 2013, 03:04 PM
I see. Thanks much. Now that I think about it there is no point in really loading sub-sonic if I am not going to use the round with the suppressor. Any good suggestions for a M9?

Mudball_3
March 3, 2013, 03:09 PM
I think that I will just end up going with 147 plated bullets.

rcmodel
March 3, 2013, 03:10 PM
I can suggest you buy a Lyman #49 reloading manual.

It has all kinds of tested 9mm loads in it.

http://www.midwayusa.com/product/217655/lyman-reloading-handbook-49th-edition-reloading-manual-softcover

Fishing for load data on the internet without a reloading manual to back it up is a good way to shoot your eye out.

rc

Mudball_3
March 3, 2013, 03:19 PM
Thanks for your help everyone. I got way ahead of myself. I am currently out at work and got a little bored. I have just ordered the Lyman 49th Edition Handbook, Lee Precision Modern Reloading 2nd Edition New Format, and the The ABCs Of Reloading: The Definitive Guide for Novice to Expert.

greyling22
March 3, 2013, 05:18 PM
good choices. everybody should have lyman and lee (if you can get past lee's promoting of their products. once you do, there is some really good info in there, and I really like the load data presentation) ABC's is pretty good for a starter book.

If you enjoyed reading about "Supressed 9mm with 158 gr SWC Leading?" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!