Case Trimming Startup


PDA






dak0ta
March 5, 2013, 09:14 PM
Hi,

I would like to get a case trimming kit to go along with my RCBS Rockchucker kit.

I want to reload .308, 6.5x55, 8mm mauser, .45 ACP, and .30-30.

Which hand trim kit is considered the best out of the box? Do I need to buy new pilots and shellholders for each of my calibers? I'd prefer to get a kit that has all this already.

Lyman Universal
RCBS Trim Pro
Forster
Wilson

Those are the brands I have seen, but Lyman/RCBS seem to be in my price range and come in a kit with almost everything.

Is there anything else I need to buy in addition to what comes in the kit?

If you enjoyed reading about "Case Trimming Startup" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
witchhunter
March 5, 2013, 10:50 PM
I started with a Lyman universal, it has a universal base chuck. You will only need pilots and I think they come with a variety pack. They all work well though.

GarySTL
March 5, 2013, 11:01 PM
I had a Foster which I sold when I stopped reloading for a while. Now that I'm back in it, I have a Redding. Works fine and has a universal chuck. Came with several pilots from 22 to 30 Cal.

GT1
March 6, 2013, 12:18 AM
I have the Lyman Universal, I really like the chuck. It has a good variety of pilots from .22 to .45. (It has the pilots for the calibers you list.)

I like the RCBS in that it has a 3-way cutter upgrade(trim/debur/chamfer), but it is $150-ish for that. I'm not a fan of that long grip/release lever on that trimmer either. Why they did that I have no idea.

All the trimmers you list are good trimmers.

kingmt
March 6, 2013, 08:15 AM
I use the Lee. Great price & they woeful great.

gamestalker
March 6, 2013, 05:18 PM
I've been using the Lee since day #1 and don't plan on changing. They're inexpensive and get the job done, and using a drill makes it fairly quick and painless to trim, ream, and chamfer all in one step.
You'll need at least one cutter, 1 threaded stud, and a case length gauge for each cartridge, and a threaded shell holder for each cartridge, unless of course the same shell holder applies to more than 1 cartridge your loading. Once you have the cutter and threaded stud, I think it will cost about $8 for each case gauge / shell holder.
It took me about 1/2 hr. - 45 minutes to prep 100 .270 win. cases last night. Not too bad.

GS

243winxb
March 6, 2013, 05:27 PM
Been using the Lyman Universal for years. It may not cut the case mouth square. The steel cutter head will need replaced after a while. Easy to replace or buy a carbide head. It does an ok job of outside neck turning with the optional tool. I would buy one again.

renomedia
March 6, 2013, 05:27 PM
I use the RCBS Trim Pro II. The kit comes with a universal shell holder and most every pilot. I upgraded the cutter to a titanium nitride redding cutter and have used it to trim 223, 6mm, and 308. The lathe shaft allows me to use a cordless 1/2" drill to power my trimming. I used to use an older Pacific (Hornady) trimmer. I like the RCBS one much better.

dak0ta
March 6, 2013, 07:06 PM
I went for the Lee Zip trim. Good reviews, simple to use, and affordable.

45lcshooter
March 6, 2013, 07:46 PM
Had Lyman universal, Hornady, and now I use Lee Trimmer with ZipTrim. Won't go back to anything else but the Lee, so easy to use, no need for re-measurement with calipers.

Hondo 60
March 6, 2013, 09:27 PM
I have a Lyman & it came with 9 pilots.

If you enjoyed reading about "Case Trimming Startup" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!