Old 9mm reloads


PDA






ExAgoradzo
March 12, 2013, 02:12 AM
I found some of my FiL's 9mm reloads.
They have corrosion all over many of them.
The brass I am assuming is trash, but if I pull the bullets I hope to save them? the powder? the primers?
What should I do to prevent the rest from corroding? I was shocked when I opened them up...Nothing else I have (mostly stored in ammo boxes or plastic bins in the attic) is corroding. But I wouldn't be a bit surprised that it came from his house and he may have reloaded these in the 90's.
Ideas?
Greg

If you enjoyed reading about "Old 9mm reloads" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
Fire_Moose
March 12, 2013, 02:20 AM
Pull the bullets and save em. Toss the powder.

Put the cases in a tumbler to see if they clean up.

If not you could even decap the primers and reuse those....though some peiple might not...

Sent from my CZ85 Combat

ExAgoradzo
March 12, 2013, 12:05 PM
Thanks Fire_Moose.
Greg

medalguy
March 12, 2013, 01:33 PM
Cautionary warning: If the brass is truly corroded, I wouldn't try to reuse it. Discolored is OK but corrosion can go all the way through and you will have a problem. 9mm is a pretty high pressure load. 9mm brass is cheap, heck I'll send you some if you need it but I see it for sale for about .03 even today. The powder, I'd toss because you can't be absolutely sure what it really is, but the bullets should tumble clean just fine and they really are scarce today.

General rule: NEVER EVER shoot anyone else's reloads. Period.

I'm not sure why ammo reloaded that recently would badly corrode. Check the area for any chemicals, leaking batteries, anything acidic? Just a thought. Maybe he was eating orange slices while reloading. :uhoh:

ExAgoradzo
March 12, 2013, 06:33 PM
No, these reloads are at least 5 years old and I'm guessing they are older than that. My FiL did most of his reloading in the 80's & 90's but he kept it up until his last few years.
Greg

ExAgoradzo
April 6, 2013, 11:56 PM
Vinegar. I cleaned them with vinegar. Some of them are too far gone to salvage, but almost all the corrosion came off with vinegar and a paper towel. Some Ill just take apart and save the components I can; some Ill shoot through my Blackhawk; then if that works, very carefully trough my M92. If they work, great: I don't think the vinegar got into the powder, Ill give a report next weekend.
Greg

gamestalker
April 7, 2013, 03:58 AM
I would personally toss the powder, but if the corrosion hasn't effected the primers, reuse them puppies, and the bullets as well. I would be careful with the brass though, 9mm is a high pressure cartridge. Maybe tumble it for a few hours and see what ya got.

I thought I read something once about vinegar having a negative impact on brass?

GS

ObsidianOne
April 7, 2013, 05:53 AM
Pull the bullets, toss the powder on the lawn or on plants. Great fertilizer. If you decap, wear glasses and do some research on it first. Whether you trusted him or not, there may be a reason he didn't shoot them. You never know, and a few hundred rounds or less isn't worth a gun, life, or limb.

Sent from my PC36100 using Tapatalk 2

Blue68f100
April 7, 2013, 10:29 AM
One advantage of using a NuFinish polish in the tumbler. It leaves a protective film.....

If you enjoyed reading about "Old 9mm reloads" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!