45ACP Lead 200 Grain TC pet loads


PDA






Schwing
July 21, 2014, 02:29 PM
I recently picked up a Lee .452 200 grain TC mold. I don't shoot a huge amount of .45 so I wanted something a little lighter (it is the tightwad in me trying to save lead).

When I first started working up loads for it, I was concerned because I had to push the OAL down to around 1.150 to get them to cycle reliably in my Springfield. I almost stopped using the mold but, after working up some loads, I am very pleased with the accuracy. Of course, I started really low and worked up to make sure there were no pressure problems.

I wanted to see if anyone here has used this mold and has any pet loads that they are happy with. Even if you have a 200 grain mold that is a RN or SWC, I would be interested. I will share mine below but would like to see what others have found. Below are my 2 best loads so far:

5 grains of Bullseye seated to 1.150

4.6 grains of Promo also seated to 1.150

If you enjoyed reading about "45ACP Lead 200 Grain TC pet loads" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!
bds
July 21, 2014, 02:41 PM
These loads are used with 12/18 BHN Missouri and 14-16 BHN Dardas/Z-Cast 200 gr SWC bullets:

5.0 gr of W231/HP-38 at 1.245"-1.260" OAL

4.0 gr of Red Dot/Promo at 1.245"-1.260" OAL
I don't shoot a huge amount of .45 so I wanted something a little lighter (it is the tightwad in me trying to save lead).
4.0 gr of Promo will also save you on powder so you can be even more "frugal" ;)

41 Mag
July 21, 2014, 05:11 PM
My lads vary from 4.5gr to 5.5grs depending on just which 200gr cast bullets I am using at the time.

I was using around 3.8 with one, and around 4.3 with another, but finally decided that even numbers were easier to remember and the accuracy was about on par either way.

I have an original H&G #68 mold as well as a couple of other SWC molds which all are listed with different loads. I just feel that as "GOOD" as I am with my 45 ACP :rolleyes:, dialing in a specific load was pretty much a wasted effort right now. :D

GooseGestapo
July 22, 2014, 01:24 PM
I use the same bullet.
My favorite (or rather the pistol's favorite) is 4.3gr of Clays or 5.4gr of Universal. Either of these will cut a ragged hole at 25yds. 5-shots ~1.5". I've also used the above mentioned Promo/RedDot loads as well as Bullseye and Win231/HP38.
Whatever you have or can get your hands on these days is "best"...

The throat on your chamber will determine where these need to be seated. Seat them to where they chamber easily with the slide going into full battery.

Some M1911 magazines won't reliably feed these. The new-style will. The older (ie; WWII style followers) won't
My Springfield M1911 will feed empty brass so feeds these "semi-wadcutters' reliably. A Springfield XD-45 I had required the bullets be seated ~.003" deeper than my M1911 chamber did. I sold the XD to a gunsmith/deputy that needed it... But it was a "shooter".. Almost as accurate as the M1911 "Match" gun..

If you enjoyed reading about "45ACP Lead 200 Grain TC pet loads" here in TheHighRoad.org archive, you'll LOVE our community. Come join TheHighRoad.org today for the full version!