1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

1911 expert advice needed - troublesome slide stop pin

Discussion in 'Handguns: Autoloaders' started by longeyes, Jan 6, 2003.

  1. longeyes

    longeyes member

    I've got a Kimber Custom II with about a thousand rounds through it. Okay, here's the problem: Pistol is a royal PIA to field strip. It is next to impossible to pop out the slide stop pin. The thing won't budge. I've had it back to Kimber in Yonkers but they returned it, supposedly "fixed," without explanation. Alas, the problem remains. When I have been able (rarely) to dislodge this sucker I have similar difficulty in getting the pin back in. What is up with this? Is it a bad pin or a tolerance problem with the frame or what? It's not me because I have a Colt Sistema with which I don't have these problems. I like the pistol otherwise but admit I am starting to prefer shooting my Glocks, if only because I know they are so easy to clean afterwards. Any useful advice appreciated.
  2. Ledbetter

    Ledbetter Well-Known Member

    Have you tried disassembling the pistol by starting with the barrel bushing? Push it out of the way, remove the plug and spring. Remove the bushing. Line up slide stop with notch and remove.

    You can reassemble the same way. Insert barrel in slide. Insert bushing, push out of the way. Replace guide plug/rod and spring. Turn bushing to engage coils of spring, place slide on frame. Line up slide stop and insert. Finally, push in plug and rotate bushing to lock.
  3. iamhistory

    iamhistory Well-Known Member

    longeyes........I had similar problems with a Springfield Mil-Spec when it was brand new. It seems to be a "tolerance" type of issue simply until the pistol gets broken in. I notice with mine, there was no trouble taken the pin out.....just a heck of a time getting it back in.

    With yours....you said it has about 1000 rounds through it. I called Springfield after about 300 rounds through mine and I was still having trouble. The rep told me she has had several Springfield 1911's and has had that happen to her a few times as well......after a while, it got much easier.

    I don't know if this is what is affecting your Kimber or not, but I would guess it is something along those lines. If you Kimber is functioning well and you haven't noticed/experienced any problems.....it could be just a tolerance issue. I can understand though......it does get very frustrating when the pin refuses to go back in. What if we had to field strip in an emergency and get it back together quickly???

    Anyway.......I continue to shoot my Springfield and take it apart/put it back together.........the pin is becoming more cooperative. I hope this helps a bit.

    Good Luck
  4. Ledbetter

    Ledbetter Well-Known Member

    By the way, if the pin is too big for the hole, sand the pin, not the hole.
  5. longeyes

    longeyes member

    Thanks, guys, for the comments. I tried again and finally got the pistol stripped. I had to wiggle the pin for a while to get it out, then play with the slide travel to get it back in and fully flush on reassembly. Maybe it will loosen up over time...? Maybe the pin needs shaving? Maybe I just need a new pin altogether? (Wilson? Brown?) Is this one of those MIM parts everyone complains about?
  6. dsk

    dsk Well-Known Member

    Try inserting the slide stop into the stripped frame. That'll tell you if the pin is a bit too big for the hole. If so, replace the slide stop.
  7. Ledbetter

    Ledbetter Well-Known Member

    Before you throw it away

    If, and only if, it is too big for the hole, wrap some emory cloth around it and twirl it around. If you are as fanatical as me, you will only do this where the pin contacts the frame, in order to maintain barrel link tightness.
  8. RpMiller

    RpMiller New Member

    Slide stop pin

    I have the exact same problem with my Ultra CPD II longeyes. I have had it for about six years now and several hundred rounds though it. Every time I go to strip it down for cleaning it takes a freakin act of congress to get that stupid thing out. I see videos all over of guys that just line up the witness mark, push on the right side and it almost falls out. I have to bang and pry on mine to the point I am SERIOUSLY worried sometimes that I am going to bend or break it.
  9. gunzee

    gunzee member

    Look at the rear surface, where the springloaded detent engages the slide stop. There used to be a common problem with the stop "popping up" during firing, so maybe your factory has started deepening the detent-dimple. You can dremel out the side of the dimple into a more gradual slope, easing the removal of the stop. Do this in several tries, highly polishing the surface and using a bit of lube on it, each try. If you go too far, you'l'l be buying a new stop, probably $20 these days, and waiting on it for a month.
  10. xXxplosive

    xXxplosive Well-Known Member

    Ya probably should have bought another Colt.............

Share This Page