1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

? about 40 S&W reloads

Discussion in 'Handloading and Reloading' started by dodgeff232, Jan 21, 2010.

  1. dodgeff232

    dodgeff232 Member

    I'm very interested in learning to reload my own ammo and I have came across some interesting info during my searches. I have a Sigma 40 and a Glock 40 and people are saying not to shoot reloads in these guns due to the chamber not enclosing the round completely. Is this true and if so is there anything I can do. I really like my hands and fingers and would not like to loose them.

    Any info would be appreciated
  2. Rodentman

    Rodentman Well-Known Member

    I shoot my .40 S&W reloads all the time. In fact I do not buy factory ammo except .357 sig. If you read and follow the reloading instructions you should have no trouble.

    The "unsupported barrel" has some potential issues. I'd suggest not loading to the max, and examining brass carefully. Perhaps use the Redding GR-X push through die for full resizing.
  3. bfoosh006

    bfoosh006 Well-Known Member

    Some loads I make for my fully supported barrel, I would never fire in a Glock barrel. The "lack" of that extra support helps with feeding, but has also caused countless cases of "Glocked brass" . As a matter of fact, so much so that Redding makes a die specifically for it..http://www.redding-reloading.com/pages/grxpushthru.html
  4. bds

    bds Well-Known Member


    I think the concern over shooting reloads in Glock barrels has to do with sharply cut ramp area into the chamber in early generation Glock barrels to aid in feeding (I believe G22/G30 mostly) and the hexagonal (or polygonal) rifling when shooting lead reloads.

    Over the years (by Gen3), Glock has improved the chamber support and newer barrels have less unsupported areas. If you have an older Glocks with less supported chamber, you can replace with newer Glock barrels or aftermarket barrels if you have any chamber support concerns. As to Sigma, I do not recall the chamber support being an issue (maybe someone else can check the Sigma chamber and comment on it).


    This less supported chamber causes bulged case bottoms when shooting factory pressure/hot loads. The problem is made worse when shooting reloads with lead bullets because the repeated sizing of bulged case stress the bulged area at the base, further weakening the case wall. The buildup of lead/fouling in barrel (especially where chamber transitions to barrel rifling) can cause excessive chamber pressure and case failure leading to hot gases blowing down the magazine well, force ejecting the magazine and causing damage to the gun/injury to the shooter.

    Conventional barrels have squared off (lands and grooves) rifling and newer pistols (Glock, H&K, Kahr) have hexagonal/polygonal rifling (hills and valleys).

    When shooting bullets in conventional barrels, pressure is lost through the grooves while the lead bullet rides down the lands. Due to the heat/pressure of powder burning, some softer lead bullets can leave smears of lead and lead slivers/fragments in the grooves along with the carbon fouling (it is for this reason modern lead bullets are not soft pure lead, but an alloy of various metals and are hard cast with hardness of 18-24 to reduce leading in the barrels). The grooves allow some build up of lead/fouling and still allow the bullet to travel down the barrel on lands while allowing the pressure to escape through the grooves.

    Of course, more frequent barrel cleaning is required if you shoot lead bullets instead of plated/jacketed bullets as plated/jacketed bullets only leave fouling in the barrel. I have shot lead bullets with 18-24 hardness in my Lone Wolf barreled Glocks and they do not lead my barrels (I clean my barrels with Hoppes #9 solvent/copper brush and barrels come out clean without any deposits).

    Because the intent of the polygonal rifling is to reduce the void between the bullet and the inside of the barrel to increase contact and reduce pressure loss, there is less void in the valleys to accommodate the buildup of lead/fouling deposit and pressure increase inside the barrel becomes more of a problem as more and more lead rounds are shot.

    Following is an excerpt from wikipedia: http://en.wikipedia.org/wiki/Polygonal_rifling

    Of course, shooting reloaded plated or jacketed bullets in Glocks is a less of a problem in regards to barrel fouling, but if you have older less supported barrels, case bulging/case failure is still an issue.

    You can shoot reloaded plated/jacked bullets and/or reloaded lead/moly coated lead bullets more safely in Glocks (especially older Glocks) by simply changing out the barrel with newer factory Glock barrels for better chamber support or with aftermarket barrels that have the conventional land/groove rifling to shoot lead bullets.

    As to your Sigma, I believe it has conventional rifling, but maybe someone else can verify this and comment.
    Last edited: Jan 22, 2010
  5. Gadzooks Mike

    Gadzooks Mike Well-Known Member

  6. uf-engineer

    uf-engineer Well-Known Member

    i replaced the barrel in my glock with an aftermarket barrel. just so i can have that piece of mind.
  7. rfwobbly

    rfwobbly Well-Known Member

    The problem stems for the round's high pressure and the thinnish walls of the 40S&W brass. From my reading I understand that the early Glock 40's were the worse offenders and that Glock has generally worked that issue out on later models. Questions about exactly when the barrel change was made is probably better asked on a Glock forum. If there is any doubt, then drop in a modern barrel.

    That being said, you'll be much better off to have a later model Glock and stay with light-to-moderate pressure loads.... loads used for general plinking or practical pistol competitions. Leave the self defense load for the factory rounds.
  8. bds

    bds Well-Known Member

    rfwobbly, I agree and somehow I did not go into the details of the chamber issue last night (must be old age catching up to me :rolleyes: ) - I updated the posting.

    And if you must load defensive loads using JHP bullets for Glocks (although I highly recommend using factory loads for carry/defense), you can consider using new brass to minimize the chamber support issue.
  9. dodgeff232

    dodgeff232 Member

    thanks for all the good info. im glad i found this place

Share This Page