1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Brass Branding

Discussion in 'Handloading and Reloading' started by YoPedro, Dec 28, 2006.

  1. YoPedro

    YoPedro Well-Known Member

    How important is it to sort brass by brand? (.45ACP) Is there a consensus or a rule of thumb to follow? I'm not into high volume lead dumps, I spend my shooting time putting ten shots in one hole, as often and as consistently as possible and perfecting the technique therein.

    HSMITH Well-Known Member

    If you are shooting at short ranges, 25 yards or less, you will be very hard pressed to measure any difference between mixed brass loads and single headstamp brass. At long range, like 50 yards, you might be better off shooting sorted brass.

    I don't sort 45 brass, nothing I do requires or even supports sorting. If the load I use will do 2.5" at 25 yards that is all I need or will be able to use in the types of shooting I do.
  3. YoPedro

    YoPedro Well-Known Member

    Brand me content.

    Bam! Said and done, I love a definitive answer!
  4. The Bushmaster

    The Bushmaster Well-Known Member

    And then you have those that agree with HSMITH, but just can't stand to see mixed brass head stamps in a box starin' up at him.:what: I sort by head stamp.:D
  5. taliv

    taliv Moderator

    yeah, i hold with those who sort headstamps, not because it makes a difference in 45acp, but because i keep records of my brass (how many times it's been shot, etc) and 50 years from now, i hope to be able to look back and associate trends in accuracy or reliability or number of firings with lots of brass, where those trends are statistically insignificant when you just look across 1000 rounds or so
  6. JDGray

    JDGray Well-Known Member

    I dont sort my 45 brass, but I do sort my 9mm:)
  7. The Bushmaster

    The Bushmaster Well-Known Member

    JDGray...Why...What's the difference? Why one (9mm) and not the other (.45 ACP)? I'm absolutely stumped...:D
  8. JDGray

    JDGray Well-Known Member

    Well... I didn't seperate untill I bought some Magtech 124gr fmj. While loading this particular bullet, I noticed a differan feel while running through my LFC die. This only happened with CBC headstamp brass. I dont know if the brass is thicker than the rest, but you could see a pronounced edge where the bullet stopped in the case, and the FC die hit this, and felt wierd. No problems at all loading this bullet in Win brass. So I decided to seperate all my 9mm brass. My crimp die is only set to remove the belling.I have no problem loading Win 115gr fmj in any brass.
  9. Father Knows Best

    Father Knows Best Well-Known Member

    I agree that there is generally no need to sort pistol brass. I'm not a bullseye shooter, though, so I don't know if those sorts of precision handgun competitions benefit from that level of detail.

    I make one exception to my "no sort handgun brass" rule, and that's for a cartridge that's kind of borderline rifle/handgun -- the 44-40. I sort my 44-40 brass for one simple reason -- I use rather large bullets (.430) in my 44-40 loads, and my 44-40 firearms have tight chambers. I have discovered that Starline 44-40 brass tends to run a little thicker (.007) than Winchester (.006) and some others. That small difference can mean the difference between a round chambering fully or not. So I use the Winchester brass for .430 lead bullet loads, and restrict Starline to lower velocity (to prevent leading) .428 hardcast.

    I also load lots of other handgun rounds, though, and I don't sort any of those. Nor do I keep track of number of firings. I just load 'em 'til they split.
  10. Walkalong

    Walkalong Moderator

    Speer .45 brass I have seen lately has much bigger flash holes than other brass. I segregate those into a seperate batch.

Share This Page