Quantcast
Kimber Compact CDP II with range report. - THR
THR  

Go Back   THR > Tools and Technologies > Handguns: Autoloaders

Welcome to THR
You are currently viewing our site as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have, access to post topics, communicate privately with other members (PM), respond to polls, and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!


If you have any problems with the registration process or your account login, please visit the help section.

Reply
 
Thread Tools
Old July 14, 2014, 11:19 PM   #1
eam3clm@att.net
Member
 
 
Join Date: December 2, 2010
Posts: 613
Kimber Compact CDP II with range report.

I am about to violate the first rule of posting about a gun purchase without posting pictures, but I cant add them right now.
I am looking for any insight or expierences on the Kimber Compact CDP II since I just picked one up. It was an impulse buy that I had not planned on but I believe that I got a good enough deal on it ($700). It has the internal extracter if that matters. The gun has some wear marks on the finish and it was obvious that it has some rounds sent down the pipe.
I will admit that I'm not a 1911 guy and I didn't do any research before the purchase. The first thing that I did when I got home was search the web to see what I had brought home. I was a little shocked by all the negative that I found about Kimbers and the problems that they had. I always thought that they were top shelf, but it seems that there has been some problems with them.
I began to get worried about the gun an I just had to shoot it. The first loads that I ran through it was some cast 200 grain SWC with bullseye that I loaded for my first 1911 purchase a few years ago (Para GI Expert). My Kimber did not like them at all. It would jam a few times with each magazine (Kimber Mags). I'm not holding this against the pistol since my XD and Glock 30 both chokes on these SWC.
I believe that it is a COL issues and not a gun issue, since the rounds were built around the Para. I managed to get 46 rounds through it before I switched to my Berry's 185 HBRN load with Acc#2. It cycled these rounds without issue. I did have several spent cases hit me in the head and I had to double check to make sure I wasent shooting my glock.
eam3clm@att.net is offline  
Old July 15, 2014, 10:09 PM   #2
burk
Member
 
 
Join Date: July 16, 2005
Posts: 255
My old one ate everything, but I did start it out with nothing but 230 gr FMJ factory loads for the first 400 rounds. One thing I did notice was that my ejection patterns approved when I went to Wulff Xpower springs, I do believe most Kimber 4" are under sprung. I would also suggest nothing but Kimber Pro Tac or Wilson 47D mags, stay away from Chip McCormick's, they don't like alloy frames. Also Ed Brown makes a drop in machined snakeskin mainspring housing that looks great on that gun.
burk is offline  
Old July 16, 2014, 10:57 AM   #3
340PD
Member
 
 
Join Date: February 18, 2007
Location: central MN
Posts: 920
I have the three inch version and have had no issues with any ammo factory or reloads.

When they first were introduced they offered a version with an external extractor that gave people some issues and I believe they replaced all the slides with the internal version now offered.

One thing I did was swap out all the factory metal followers on the Kimber mags with the rounded polymer Wilson version. The flat metal follower on the Kimber factory mags was chipping the alloy frames of the gun. Whether or not this contributed to the flawless performance of my gun, I do not know.
340PD is offline  
Old July 16, 2014, 09:35 PM   #4
shooter1
Member
 
 
Join Date: January 14, 2004
Location: In the shadows.
Posts: 881
I've owned a few Kimbers (3). Haven't owned or seen a bad one yet. I still own a Pro Carry 4". It shoots with my more expensive 1911 pattern pistols. It, as well as the 3" Ultra Carry and the 5" Custom Target, were all flawless and accurate. If your 4" won't handle 200gn LSWC, it's a loading problem, not a gun problem. As you are already loading BE powder, try 4.8gns and an OAL of 1.24-1.25 very light crimp. That load is well within published load data. Be sure to chamber check every round to be sure everything is in spec. If that loading won't run in that gun, chances are it won't run 100% with anything.
It has been a great load for any .45s I've tried them in, including a Glock 21 & 36.
I heard all the chatter about metal magazine followers destroying the feed ramp on the aluminum frame. Problem was I had about 3k rds through it by the time I heard. There was zero indication that either the Ultra or the Pro had ANY damage to the frame from the mag followers. Just the same, I had a dozen or so Chip McCormic 8 rounders, so I ordered Night Hawk Custom springs and followers and changed out the metal ones. They work great too.
Good Luck! You have a nice pistol.
str1
shooter1 is offline  
Old July 16, 2014, 09:54 PM   #5
G'dale Mike
Member
 
 
Join Date: February 11, 2013
Location: Gardendale Al
Posts: 89
I loved my cdp and never had a minute's problem out of it.
G'dale Mike is offline  
Reply


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:43 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
vBulletin Optimisation by vB Optimise.
This site, its contents, Shooting Reviews, and its contents are Copyright (c) 2010-2013 Firearms Forum, Inc.
IMPORTANT DISCLAIMER
Although The High Road has attempted to provide accurate information on the forum, The High Road assumes no responsibility for the accuracy of the information. All information is provided "as is" with all faults without warranty of any kind, either express or implied. Neither The High Road nor any of its directors, members, managers, employees, agents, vendors, or suppliers will be liable for any direct, indirect, general, bodily injury, compensatory, special, punitive, consequential, or incidental damages including, without limitation, lost profits or revenues, costs of replacement goods, loss or damage to data arising out of the use or inability to use this forum or any services associated with this forum, or damages from the use of or reliance on the information present on this forum, even if you have been advised of the possibility of such damages.