Quantcast
What clever little things have you "invented or discovered" that you can share? - Page 4 - THR
THR  

Go Back   THR > Ammunition, Gear, and Firearm Help > Handloading and Reloading

Welcome to THR
You are currently viewing our site as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have, access to post topics, communicate privately with other members (PM), respond to polls, and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!


If you have any problems with the registration process or your account login, please visit the help section.

Reply
 
Thread Tools
Old November 4, 2006, 05:48 AM   #76
Joe D
Member
 
 
Join Date: February 21, 2004
Location: Alabama
Posts: 275
Mink Oil is one of the best case lubes I have ever used. Just swipe your forefinger across the surface every 5 or 6 cases. When you pick the case up a little get deposited on the neck. Does not take much at all. Smells good also.
Put an empty .45ACP case on the plastic primer rod for Dillon primer feed.
A Vibra Prime will be the best $25 you will ever spend. You can fill a primer tube in 5 seconds with this thing.
Best tumbler I have ever used is the Hornady M3. Holds over 1,500 9mm rounds.
The 9mm and .40 Dillon shell plates are the same. Just change the brass pins.
Walnut or corn cob can be bought at your local sand blasting supply house dirt cheap. Paid $17.50 for 50# of walnut.
A regular Lee carbide .40 S&W die will remove the Glock bulge on 99.999% of the brass. The "U"/EGW die does not work any better.
__________________
Miss? That can't be a miss. Looks like a perfect double to me.
Joe D is offline  
Old November 4, 2006, 09:49 AM   #77
capbuster
Member
 
 
Join Date: December 25, 2002
Location: Bessemer,Alabama
Posts: 220
wow what a wealth of information. I dont know if I can add any helpful hints but here goes.most of these are borrowed suggestions and although I have taken them as my own I was not the creator. You might consider mounting a small vise at one end of your reloading bench. It is great for small projects and you can mount such things as powder measures to it with the addition of wooden blocks attached to the device used.one forum member mentioned the importance of having one can of powder on your bench at a time and I strongly agree.different types of powder from the same manufacturer come in similar shaped canisters and one day I almost loaded bullseye for unique,not good. I now keep a small notebook in the cabinet where my powder is stored. I record the bullet type, powder type and load,and date each time I pull out a can of powder making sure that I have looked at the canister and read out the type I have in my hand.I use a dillon 550 progressive for most of my 45acp loading and the following are some things that I have used to make life easier for me.I use a universal deprimer and a rcbs single stage press to depime my cases. the rims of fired cases are checked by inserting them rim first into a case gage such as my dillon brand. if they slide in,they are reloaded,if not they are canned. may sound wasteful but it seems to cut down on failures.One of my big concerns is a properly seated primer and on my dillon press, I seat the primer,rotate the case and apply pressure again,remove the case and check its bottom with a steel rule to see if the primer is flush or better. I know it takes time but it makes me happy.finally I have a lamp positioned where I can check the powder level before a bullet is seated.
__________________
Cliff
capbuster is offline  
Old November 9, 2006, 06:37 AM   #78
redneck2
Member
 
 
Join Date: December 25, 2002
Location: Northern Indiana
Posts: 7,481
By mc223

Varget and the Dillon powder measure.

Over the past few months there have been a few threads about bridging and related problems with Varget and other stick powders in Dillon powder measures and small mouth cases.
I had the same problem with mine, so I set out to cure the problem. First came polishing the drop tube. Helped some, but still had an occasional mess to clean up. So I used a taper reamer to enlarge and smooth the drop tube followed by an extra fine polishing. Much better but still got a bridge about 1 in 250 rounds.
I worked at a place once that mixed chemicals. Mostly granular type stuff. They used shakers to keep the stuff flowing.
I used a small sealed electric motor and a piece of 1/2 in scrap steel mounted to the motor shaft like the one used on tumblers. This assembly was then mounted to the Dillon Strong mount and wired to a dimmer switch to control the shaking force.
Powders flow smoothly and more accuratly. And since the whole machine is vibrating there is some settling of the powder in the case, which reduces the old familiar crunch. Bullet seating seems smoother also.

This system is in place and operating. The drop consistancy at .1 grain.
__________________
I used to have superpowers, but my therapist took them away
redneck2 is offline  
Old November 9, 2006, 09:25 AM   #79
Starter52
Member
 
 
Join Date: October 16, 2005
Location: Northeast USA
Posts: 1,561
Fantastic thread. Keep 'em coming, guys. I've filled half a notepad already.
Starter52 is offline  
Old November 11, 2006, 04:18 AM   #80
Shawn Dodson
Member
 
 
Join Date: December 28, 2002
Location: Bremerton, WA
Posts: 2,116
As a former technical writer I tend to write my own procedures for complex tasks, primarily so I don't have to thumb through owner's manuals to find the manufacturer's procedure, to document helpful notes, and to have a simplified outline type procedure to follow. Because there are times when I go long periods without reloading I put together the following procedure for operating my RCBS Pro-2000 progressive press that I keep posted at my reloading bench. It refreshes my memory and brings me right back up to speed: http://www.firearmstactical.com/pdf/..._Procedure.pdf
__________________
/s/ Shawn Dodson
FirearmsTactical.com

"The fight will not be the way you want it to be. The fight will be the way it is. You must to be flexible enough to adapt." -- Unknown
Shawn Dodson is offline  
Old November 15, 2006, 12:10 AM   #81
Navy joe
Member
 
 
Join Date: December 24, 2002
Location: VA
Posts: 2,362
Place a piece of aluminum foil over the top of your Dillon powder hopper and then press the lid down on it. Helps keep the powder airtight, but most importantly dissipates the static cling that sticks powder to the side of the measure.
__________________
FY47012 , Shut up and shoot.

USPSA, NRA, VCDL
Navy joe is offline  
Old November 15, 2006, 04:25 AM   #82
MikeHaas
Member
 
 
Join Date: October 24, 2003
Posts: 291
My site? http://ammoguide.com/



Mike
MikeHaas is offline  
Old November 21, 2006, 10:56 PM   #83
GaryL
Member
 
 
Join Date: November 21, 2006
Location: MN
Posts: 1,060
A couple people mentioned losing track of the powder in the powder measure (and only keeping one powder on the bench at a time or using a post-it). I made that mistake once, but got lucky because I had Red Dot in the tube. Ever since I put a 3x5 card with the powder written on it in the tube, so I always know whats in it.

I also use Mobil 1 for gun lube. I figure a gun is an internal combustion engine that throws away the piston, and it's hard to compete with the R&D funding of a major oil company....

I'm going to try to attach a pic here of the reloading cabinet I made:
Attached Images
File Type: jpg ReloadCab1.jpg (106.5 KB, 2362 views)
GaryL is offline  
Old November 22, 2006, 04:12 PM   #84
phique2000
Member
 
 
Join Date: November 10, 2006
Location: Mt. Holly, NC
Posts: 6
Since I only load handgun, I made a lockring that fits around the ram of my Lee turret press, set it about in the middle of the ram, and now I have a nice short stroke.
phique2000 is offline  
Old November 26, 2006, 02:38 PM   #85
earplug
Member
 
 
Join Date: October 9, 2006
Location: Colorado Springs
Posts: 1,513
Single Stage press primer

Some times the coil spring on the primer seater is stronger then needed. The seater cup will drag on on the case holder, the cup and spring will toss the primer out of the cup. This results in upside down primers, or sideways primers. Cut a coil or two out of the spring.
Polishing the bottom of the case holder helps too.
earplug is offline  
Old November 29, 2006, 01:21 PM   #86
ilbob
Member
 
 
Join Date: June 14, 2006
Location: Illinois
Posts: 7,694
great ideas.

i toss a paper towel in the tumbler. the towel gets pretty dirty. my media is probably 15 or 20 years old.
ilbob is offline  
Old November 29, 2006, 04:15 PM   #87
Walkalong
Moderator
 
 
Join Date: November 20, 2006
Location: Alabama
Posts: 36,169
Quote:
I'm going to try to attach a pic here of the reloading cabinet I made:
Real cool organized setup. Way better than mine.
__________________
Do you ever wonder why nobody ever robs the bag man for the mob? No, you don't.

"Oh bother" said Pooh, as he chambered another round. Author unknown.
Walkalong is offline  
Old December 13, 2006, 09:23 PM   #88
TooTaxed
Member
 
 
Join Date: December 31, 2002
Location: Columbus, Georgia
Posts: 1,255
Standardize on powder! I now use #231 for all pistol from 9-mm Makarov up to .45 Colt, #4895 for all rifle from .223 up to .30/06. Besides the cost benefits...buy in bulk!...you always can recognize what you have in the powder measure! And it saves a LOT of space on my powder shelf. (For years I had about a dozen expensive little cans of different powders... )

The 2-1/2 lb clear, square-shaped, wide mouth snack nut containers from Sam's Club make super containers for cartridge cases. They stack nicely and are labeled by strip lablemakers. And, you get to eat the nuts first!!! Biggest problem: getting the original labels off...

A small, folding Black & Decker workbench makes a fine portable bench for all single-stage tool loading and case trimming operations except full length resizing rifle cases, which is best done on a heavy workbench. Bolt a 3/4" piece of plywood to the top to strengthen it. I frequently get a lot of case processing done while watching television, as I like to have my hands busy...everything but loading powder!!! That needs to be done away from TV and other distractions where you can keep your full attention on the process.

Keep a medium-sized 3-ring binder, tabbed by cartridge, for reloading notes, shooting test load notes, ect...you'll be surprised how much you use it!

Different sizes of Zip-Loc plastic bags are great for organizing odd lots of brass, cartridges to be salvaged, die sets, ect. Easy to label and see what's in them, protects from moisture.

The plastic fishing lure trays from Wal Mart are great for storing small parts and tools...adjustable compartments, simple labeling.

Plastic garbage bags make fine reloading tool covers.

I built a four-level 2' x 2' shelf stack 6' high from 2 x 4s and 3/4" plywood next to my main loading bench...unprocessed cases on top, sized and decapped cases below, then primed cases, then full-loaded cartridges on the bottom shelf, all organized from left to right by size of cartridge. Bulky stuff like my case vibrator, media, and media separator fit on the floor beneath. At a glance I can see where I'm running short...

Two or three inexpensive single-stage presses mounted side by side, each with a different die, makes a "poor man's progressive". (Yes, I've owned two progressives,,,but find that most of my reloading is still done single-stage...cartridges I don't shoot often, test batches with slight variations in powder charge and/or seating depth for different bullet weights and types...I like to find optimum loads for a particular firearm...and they do differ! )
__________________
John
NRA Benefactor Life Member, ex-Californian

To determine how every Congressman has voted on anti-gun bills, check here:

http://www.bradycampaign.org/facts/scorecard/

Hint: Check Barack Obama, Hilary Clinton, Nancy Pelosi, Ted Kennedy, Chuck Schumer, Dianne Feinstein, John Kerry
TooTaxed is offline  
Old December 13, 2006, 11:42 PM   #89
flutedchamber
Member
 
 
Join Date: October 1, 2006
Location: NJ the state of total despair
Posts: 51
Getting labels off of containers

To remove stubborn labels from containers I first heat them with an old blow drier. After about a minute, start to peel one corner of the label where you heated last slowly away from the bottle. Use more heat if the glue is not giving up easily. When the label is off, use Goo Gone or any cleaner with orange oil in it to remove the sticky mess that is left. Hope this helps you, Too Taxed.
flutedchamber is offline  
Old December 13, 2006, 11:44 PM   #90
TooTaxed
Member
 
 
Join Date: December 31, 2002
Location: Columbus, Georgia
Posts: 1,255
Thanks, FLUTEDCHAMBER! I'll give it a try.
__________________
John
NRA Benefactor Life Member, ex-Californian

To determine how every Congressman has voted on anti-gun bills, check here:

http://www.bradycampaign.org/facts/scorecard/

Hint: Check Barack Obama, Hilary Clinton, Nancy Pelosi, Ted Kennedy, Chuck Schumer, Dianne Feinstein, John Kerry
TooTaxed is offline  
Old December 21, 2006, 08:23 AM   #91
4fingermick
Member
 
 
Join Date: August 10, 2006
Location: Bathurst, Australia
Posts: 317
My ideas.

It's late and I am too tired to read all of these, so I acknowledge anyone who came up with these as well

Handy bits:

Get a pair of big funnels from the junk import shop. Cut the spout to an inch or so on one. Use the short funnelled one for returning powder to the tin without spilling it also useful for dumping a box of Federal Primers in their goofy big packets onto a small Lee or similar flipper tray. Place the funnel mouth on the flipper tray, hold it on place and dump the primers into the funnel (make sure you keep it in the cupboard so it is not clogged with dust, etc or wipe it before use.) Lift slowly and your 98% federal primers wll be all on the tray! (I call them this, because you normally can only get a maximum of 98 on the tray, two (at least) always end up on the floor.

Ammo tins: I store all primers in these (you need 50 cal ones if you are using those pesky Federals). Also each handgun round I load has the bulk ammo stored in these and I decant from these into range boxes.

Plastic meat trays/ice cream trays, etc: ALDI stores in Australia have excellent plastic ribbed meat trays which clean up and are very handy, as are ice cream buckets for trays while you are loading/polishing, etc, can't seem to have too many. In this house, the ice cream containers are Dad's, OK?

Plastic zip lock sandwich bags with white label panel:

These are especially handy for working up loads. Each level (10 at the lowest level, handy to have a few extra if something goes wrong and 5 for each other level) is placed in them and when fired, placed back into the same bag so that you can examine carefully for pressure signs at home without the distractions of the range, etc). I always carry a few bigger ones as well, just in case I pick up some brass, etc.

Loading dies:

Keep a spare pack of decap pins of each type. Write on the shelf where you stored them, it's often a long time between uses and you might not remember and have to pull everything apart (ask me how I know this :-) ).

If you have a calibre where you load two types of bullet, make up a tag which shows what the die is set up for (marked on both sides), this works especially well with the Lee upright dies holders.

I keep my eyes open and buy spare seating dies when I can, this saves you a lot of fiddling. They are usually very cheap when sold as an odd die (the micrometer option would be the best option.)



Dummy rounds:

I keep samples of each bullet used, clearly marked, in labelled zip lock bags if there is many of them. This allows very quick seat die set up.

For each rifle, I also seat a flat based bullet back to front in an empty case and close the action carefully and extract it carefully. This will give you a quick eyeball gauge that you can comare against any loaded bullet to see where in realtion to the start of the lands the bullet sits.


Powder:

I only have one tin on the bench at a time. This will be returned before getting another one out. You don't want to be mixing Bullseye with your Lincoln Logs!

Loading tricks:

When setting up a bullet seating die which I am going to roll crimp as well (yeah I know, Ive tried separate roll crimping on numerous occasions and it never made that much of a difference to me, not enough to add another stage to the loading process. Not many people believe me on this, I'm going to have to conduct this test again) I always seat at least three bullets before applying the roll crimp. If you screw up, you dont have to start again, just pick up the second round and use that.

If just setting the dies up or changing the settings, bullets, etc, I always try the rounds in the chamber of the revolver or auto before I crank too many of them out.

If I am using softish bullet lube, I pick up a round very frequently and comare it aginst one of the first ones I have loaded, to make sure the seater is not getting plugged with lube and affecting the depth setting. Doesn't happen very often, but huge pain when it does.

Progressive presses:

careful now! I always stop at exactly the same stage in the loading operation if interrupted. I have explained this to my family and if they see me cranking them out they wait a moment until I stop. I stop with the handle raised, a bullet seated in the charged case (seals it if I have to leave the press for a while) and an empty on the launch pad. I know when I return to loading, I just have to pull the handle and I am back in business. I absolutely refuse to stop at any other point.

I also try and go to the toilet before I go downstairs to load or tinker, because if I don't I'll be back shortly. We call it a gravity attack :-)

Boy, that guy sure can talk! Sorry about that!

Mick.
4fingermick is offline  
Old December 21, 2006, 08:45 AM   #92
robertbank
Member
 
 
Join Date: December 3, 2004
Location: Canada
Posts: 583
Hey Mick thanks for those. Never thought to be on the look out for the seater dies.

Take Care

Bob
__________________
Bill C 68 making Canada safe for criminals everywhere.
robertbank is offline  
Old December 21, 2006, 07:17 PM   #93
4fingermick
Member
 
 
Join Date: August 10, 2006
Location: Bathurst, Australia
Posts: 317
Yeah I visit one shop which always seems to have an odd die or three. When I get a big order together, I get them thrown in as a sweetner usually. When I'm not buying and just looking I sometimes just bury them at the back of his heavily laden shelves .

I remember Peter Abela (gone now) who owned the biggest gunshop in Australia. He had a huge low table with tons of boxes of bullets on it. I use to fish through looking for oxes with old price tags, etc which were cheaper than the others. The table also had a low shelf which was also loaded heavily. If I saw anything that I wanted, but couldn't afford, I used to salt it away under the table and retrieve it sometimes months later when I was cashed up. This was in the days when I had the breeze in my drawers bringing up kids and shooting and hunting on a shoestring.

I was looking for a box of bullets one day and couldn't find any of the type that I wanted I asked Peter if he had any out the back and he said 'no, don't you have any stashed under the table?' Sprung! He didn't mind though, he knew I'd be back to get them later.
4fingermick is offline  
Old December 21, 2006, 07:39 PM   #94
4fingermick
Member
 
 
Join Date: August 10, 2006
Location: Bathurst, Australia
Posts: 317
New style Lee Auto Disk Powder Measures and conversion kits.

Another thing that I do, no doubt everyone does this, but when I first started using the new type powder hopper on the Lee Powder Measures, I used to spill a bit of powder removing the hopper. PITA, got into the press workings everytimes. The system I worked out is that when I want to change the disk/powder/whatever, I twisted the hopper and cut off the powder supply to the die. There will still be a bit in the workings. I place a fired case under the die and work the press once or twice, tip the powder into the hoppe, one or two pumps more and I have all of the powder out of the workings and back into the hopper. I then remove the hopper assembly without spilling a drop. I was very pleased with myself when I worked this out. Probably outlined in the instruction manual and probably everyone else didn't have to 'invent' it, but it works for me and makes those new hopper conversions indispensable.

Another thing for RCBS Rockchucker users who load pistol and short rounds:

See if you can pick up an old 'Case Kicker.' These are great bits of gear once you learn to drive them and eject the shell automatically when you are sizing, seating, crimping, etc. When you are charging the cases or loading long cases you just swing the ejector spring (part no2 in the diagram) out of the way and by pass it. This little gizmo is worth it's weight in gold.

here is the link, the Case Kicker is on Page 16. handy diagrams as well.

www.rcbs.com/equipment/Parts_Book.pdf

Mick.
4fingermick is offline  
Old December 21, 2006, 09:14 PM   #95
Darth Muffin
member
 
 
Join Date: November 9, 2005
Posts: 184
Here's a quick tip I saw on another forum that I plan to try:

Use a gravity fed dry cat food dispenser to hold your bullets, place in on your bench right next to your press to minimize hand motion. You won't have to refill it for a LONG time and fresh ones are always right there at hand in front.
Darth Muffin is offline  
Old December 29, 2006, 02:13 PM   #96
Babalouie
Member
 
 
Join Date: December 2, 2004
Location: South Florida
Posts: 412
For Shot reloader...Get a cookie sheet pan, the kind with a 1/2 inch lip, lay it down on the bench and mount/bolt your MEC reloader right through it. Now when you have a double charge of shot, or dropped shot, as seems to happen much more often that it should, all of the shot stays in the pan and not on the floor.
Babalouie is offline  
Old January 3, 2007, 12:09 AM   #97
Tidewater Tom
Member
 
 
Join Date: December 6, 2005
Location: Tidewater Virginia
Posts: 22
Gewehr98 said:

"4. If you're in the habit of leaving powder in the powder measures of your Dillon press, do yourself a favor and rubberband a card or sticky note to the hopper with the powder type and charge weight. Don't assume the charge weight is dead on after coming back to the press, either. Weigh it."

Well my only small contribution to this good thread is that I use blue painters tape on my Dillion powder measure tube. I use a sharpie to mark it with the appropriate info; powder type, etc. It comes off easy and clean when I'm ready to change loads.
__________________
Tidewater Tom
Tidewater Tom is offline  
Old January 3, 2007, 09:23 AM   #98
Clark
Member
 
 
Join Date: January 3, 2003
Location: Where I5 meets the rain forest
Posts: 3,979
I put a Lee Loader decapping rod in a collet bullet puller.
This makes the stiffest and stoutest and best centered decapper possible.

You may have to shorten the rod.
Clark is offline  
Old January 3, 2007, 09:37 AM   #99
kahr404life
Member
 
 
Join Date: September 21, 2005
Location: North Carolina
Posts: 283
Good ideas.
__________________
"I do believe that where there is a choice only between cowardice and violence I would advise violence". Mohendas Gandhi

"Only the dead have seen the end of war". Plato

"That which does not kill us makes us stronger". Nietzsche

"The dead take with them to the grave only that which they have given away". Anonymous

"The only thing necessary for the triumph of evil is for good men to do nothing". Edmund Burke
kahr404life is offline  
Old January 8, 2007, 10:01 AM   #100
Bronson7
Member
 
 
Join Date: February 20, 2003
Posts: 203
New use for a cat feeder:
Bronson7
Attached Images
File Type: jpg IMAGE046.JPG (88.5 KB, 1925 views)
Bronson7 is offline  
Reply


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:03 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
vBulletin Optimisation by vB Optimise.
This site, its contents, Shooting Reviews, and its contents are Copyright (c) 2010-2013 Firearms Forum, Inc.
IMPORTANT DISCLAIMER
Although The High Road has attempted to provide accurate information on the forum, The High Road assumes no responsibility for the accuracy of the information. All information is provided "as is" with all faults without warranty of any kind, either express or implied. Neither The High Road nor any of its directors, members, managers, employees, agents, vendors, or suppliers will be liable for any direct, indirect, general, bodily injury, compensatory, special, punitive, consequential, or incidental damages including, without limitation, lost profits or revenues, costs of replacement goods, loss or damage to data arising out of the use or inability to use this forum or any services associated with this forum, or damages from the use of or reliance on the information present on this forum, even if you have been advised of the possibility of such damages.