Quantcast
The Marlin 39 Club - Page 96 - THR
THR  

Go Back   THR > Tools and Technologies > Rifle Country

Welcome to THR
You are currently viewing our site as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have, access to post topics, communicate privately with other members (PM), respond to polls, and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!


If you have any problems with the registration process or your account login, please visit the help section.

Reply
 
Thread Tools
Old September 14, 2009, 11:17 PM   #2376
tubeshooter
Member
 
 
Join Date: August 15, 2006
Posts: 1,040
Cool A little something for the club

Finally got to do a little shooting this past Sunday. Had a good session. This particular trip was all about sighting in, so it wasn't the average plinking session.

I took 3 brands along, Federal Champion HP, Winchester bulk HP and Federal Champion round nose. I also took along a few Shoot 'N C targets.

Those Shoot 'N Cs are helpful for sighting in. The smaller ones are still hard to see at 25 yards, but still pretty good. The bigger ones I'll save for the 50 yard line.

Gun was shooting to the right with all 3 brands. Gave the Skinner dovetail a few taps to the left, and it's shooting better now. Not perfect... but better. There was a light variable wind (5-10 mph) too, so that could have been a bit of a factor.

Still - towards the last third of the session, I wasn't missing much.

I topped it off with two Aguila Interceptors in the chamber. They are 40 grain with a gentle meplat to them. Rated at 1470 fps on the box (for what it's worth); the power over the other 3 brands above was noticeable. Seems like it would be a near-ideal hunting round, with more body to it than a Stinger or some of the other lighter hyper-vel loads. Me likey.

Now that I've gotten back to a computer, I see that I should try tapping the front sight the opposite way that I want the round to go (a little right) to hopefully get the rounds to shoot a little more left. But first... I have to clean the barrel and repeat some testing to make sure it shoots the same as it does fairly dirty. It's been awhile, and I don't clean after every session.

It's only about a half-inch off at 25 yards right now with any brand. Maybe I'm asking too much, I don't know. It is bulk ammo, after all. Thoughts?


All in all, it was a good session. Almost there. Can't wait for the next one!
tubeshooter is offline  
Old September 18, 2009, 03:14 PM   #2377
shoot
Member
 
 
Join Date: July 14, 2009
Location: Quartz Hill, CA
Posts: 12
Brass Rear Sight ?

Could someone tell me who makes the brass rear sight in "SGW42's" post of Sept. 5th. And I would be interested to know how well it works compared to the original sight.
Concerning the ammo posts, my 2007 M39A only reliably shoots CCI Mini Mags. After shooting any lead ammo, the shells get stuck in the chamber and have to be pried out. The shells from the lead ammo always are bulged out and distorted at the back of the shell where the firing pin strikes; not so with the CCI Mini Mag shells. Very annoyed and perplexed with the lead.
Thanks,
shoot is offline  
Old September 18, 2009, 04:22 PM   #2378
Flynt
Member
 
 
Join Date: August 17, 2003
Location: Dallas-Ft. Worth Metroplex
Posts: 365
I have a 1959 Mountie, which is very accurate. However, the cartridge stop broke recentlly, and the gun jammed. I ordered a new one (cartridge stopm not gun), but the gun still jams. The new stop (I'm using the old spacer washer) doesn't retain the rounds in the magazine. When I work the lever, two rounds pop out. I broke the gun down and pushed 3 rounds into the magazine. The cartridge stop will retain them, but when I slide the bolt back and depress the stop, 2 or 3 rounds pop out.

I apologize if this topic has been covered in previous discussions, but I'd really like some advice. Thanks.
Flynt is offline  
Old September 18, 2009, 05:24 PM   #2379
McRuss
Member
 
 
Join Date: September 18, 2009
Location: Lakehills, Texas
Posts: 3
Newbie

Just found this 'club.' I've owned my 39A, SN M8536, since I was about 14. I have it in pieces right now, getting ready to have it re-blued (I did a cold-blue refinish myself about 40 years ago and it is ready for a professional re-do.) But to the point: the butt plate was chipped about 20 years ago and I have not been able to find one. Any good source for this part would be appreciated. BTW, I paired it with an S&W Model 39 (appropriate I think) in nickel that I carried as a duty weapon for many years. These are my two favorite guns, just need to get the Mountie back in service.
McRuss is offline  
Old September 18, 2009, 08:47 PM   #2380
dfariswheel
Member
 
 
Join Date: December 26, 2002
Posts: 5,986
For butt plates see these places. Note that plate styles did change over the years. Also there are replicas around.

http://www.e-gunparts.com/model.asp?idDept=158

http://www.jackfirstgun.com/

http://www.gun-parts.com/marlin/

http://www.poppertsgunparts.com/cgi-...a_gunparts.cgi

Replicas:
http://www.vintagegungrips.net/mabu1.html

LOTS of style of replicas:
http://www.gungrip.com/searchresults...rchTerm=marlin
dfariswheel is offline  
Old September 19, 2009, 09:35 AM   #2381
SGW42
Member
 
 
Join Date: December 20, 2007
Location: Houston!
Posts: 739
Quote:
Could someone tell me who makes the brass rear sight in "SGW42's" post of Sept. 5th. And I would be interested to know how well it works compared to the original sight.
Tim Skinner aperture sight.

www.skinnersights.com

It was incredibly easy to install and works wonderfully. I've never heard of anyone speaking badly of them. He will make you any size aperture and front sight you want.
SGW42 is offline  
Old September 19, 2009, 12:22 PM   #2382
shoot
Member
 
 
Join Date: July 14, 2009
Location: Quartz Hill, CA
Posts: 12
SWG42,
Thanks for the reply. I'll check out his website. Can the new rear sight also work with the original front sight or do you have to install a new front sight also?
shoot is offline  
Old September 19, 2009, 08:39 PM   #2383
SGW42
Member
 
 
Join Date: December 20, 2007
Location: Houston!
Posts: 739
With my '06 or '07 manufacture 39A, I can (and do) use the factory front sight with the Skinner. Just folded the factory rear leaf down.
SGW42 is offline  
Old September 21, 2009, 08:15 PM   #2384
Cardboard_killer
Member
 
 
Join Date: September 6, 2009
Location: Florida
Posts: 47
Marlin issue

Hey all,

Got my first marlin 39a this week. I went to a gun show and there were about 10 of them in various states. I picked up a 39a golden from circa 1981 with good looking wood and overall very good condition. However, something I didn't notice until I got home, and this is because I am a total newbie to lever action guns, is that the lever does not sit flush with the stock. Picture below. I haven't yet fired the rifle, but otherwise it seems in perfect shape. Action feels nice, innards look right, it cycles rounds fine, the trigger drops. Is it something I should be concerned about? Anyone have any ideas of why the lever won't sit flush with the stock?
Attached Images
File Type: jpg marlin.jpg (79.0 KB, 64 views)
Cardboard_killer is offline  
Old September 23, 2009, 09:00 PM   #2385
McRuss
Member
 
 
Join Date: September 18, 2009
Location: Lakehills, Texas
Posts: 3
I'm not an expurt but from what I see, I'd guess someone refinished or replaced the stock and got carried away with sanding it. My Mountie is a metal to metal fit when the lever is closed.
McRuss is offline  
Old September 23, 2009, 09:01 PM   #2386
McRuss
Member
 
 
Join Date: September 18, 2009
Location: Lakehills, Texas
Posts: 3
Thanks for the links, I've tried a couple, not having too much luck with their descriptions, don't want to order the wrong version.
McRuss is offline  
Old September 23, 2009, 09:17 PM   #2387
Micro
Member
 
 
Join Date: August 30, 2009
Location: Newport News, Virginia
Posts: 155
I had a 39A and sold it, and now I want another. My rifle was purchased in the mid 90's. I installed the scope rail that came with it. I bought some Millett rings and put a Weaver 2.5x-7x scope on it. It was a friggin death-ray on squirrels. I don't hunt much anymore (I fish a lot, though). But I'd still love to have mine back and just fondle it for awhile.
Micro is offline  
Old September 26, 2009, 08:51 PM   #2388
jwmtx
Member
 
 
Join Date: May 11, 2008
Posts: 30
Cardboard Killer, It looks to me that it is just hanging down. There is a flat tension spring inside that you can increase the tension on take up the slack. Easy to do. Just take the rifle down with the take down screw and it will be obvious.
James
jwmtx is offline  
Old September 26, 2009, 10:44 PM   #2389
billybob44
Member
 
 
Join Date: July 16, 2007
Location: Central Indiana
Posts: 850
Thumbs up "Golden 39A"

My very first gun=Marlin Golden 39A. Bought in '68' with paper route $ new for $89.95, from Sunshine Hardware, Naples, Fla. Got a lot of use over the first 20 years. Marlin had a "Tune-up" program-sent back to them for all worn springs/screws to be replaced-had factory re-blue, new gold trigger, outer shot tube replaced, and sling swivels installed. Cost about $125.00, back then, but came back a like new rifle. Will stay in my family for generations to come....
billybob44 is offline  
Old September 27, 2009, 01:32 PM   #2390
Mal H
Administrator
  
 
Join Date: December 20, 2002
Location: Somewhere in the woods of Northern VA
Posts: 15,497
Quote:
Originally Posted by Cardboard killer
the lever does not sit flush with the stock.
It's hard to tell from the picture, but that looks normal to me. The lever is not supposed to sit flush with the stock, it should standoff uniformly about 1/8" inch. Is the ear on the lever located just behind the trigger touching the plate? If it is, then there's no problem. If it isn't, then the spring jwmtx mentioned needs adjusting or replacing. With the lever fully open, remove the screw forward of the lever to remove the spring for "adjustment".
Mal H is offline  
Old October 1, 2009, 01:11 AM   #2391
JustsayMo
Member
 
 
Join Date: October 20, 2004
Location: the Evergreen State
Posts: 1,394
Managed to get the 39 out for a walk this morning.



Only kicked up one grouse and he wouldn't leave the thick cover - smart bird, twice now this same dude has rejected my invitation to supper.

Decided to do a little plinking instead.

This gives me an idea for another 39 match...
JustsayMo is offline  
Old October 1, 2009, 12:00 PM   #2392
alde
Member
 
 
Join Date: December 4, 2007
Location: Bremerton, WA
Posts: 158
JustsayMo,

I was planning to get out with my 39A and do the same thing but my buddy couldn't go. May try next week. I was going to try the eastern foothills of the Olympics near the base of the Hood Canal. There are some nice areas that look like they can be productive. There is quite a bit of hunting pressure in there though. Just have to go during the week and be willing to work a little.
__________________
AL

PAX PER POTENS
alde is offline  
Old October 9, 2009, 11:24 PM   #2393
teetertotter
Member
 
 
Join Date: October 8, 2009
Location: Janesville, WI
Posts: 188
Bought my first new rifle Oct 06 and is of coarse a 39A. I was interested in shooting steel chicks, pig,turkeys and rams at the time. I finally joined the Beloit Rifle Club Dec. 08 and started shooting indoor paper Silhouette. We moved to outdoor range in April. I have moved up to class A which was my objective by end of Sept 09 shooting every Thurs eve. I will be doing a lot of indoor practicing over the winter season. Rifle is currently at the gunsmith for trigger work to 2.5lbs and can be 2# min. in hunter class. That should improve my accuracy to move me up into AA class by end of Sept 10. Also, gunsmith is bore sighting my new Simmons 6.5 - 20 X 44 that I am excited to try out. I should really be able to knock off those steel turkeys and rams 2010! Practice wil be in my book more and more. I also bought my first S&W 22a pistol this past summer. I love it too and does well knocking off those steel objects! I will be doing more practicing with it too, over the winter at our indoor range. I stand by my 39a as my first firearm! Now if I can only hold it steady as a rock!
teetertotter is offline  
Old October 9, 2009, 11:53 PM   #2394
Nematocyst
Member
 
 
Join Date: August 5, 2005
Location: Downeast Maine
Posts: 11,648
Totter (or should we call you Teeter for short?), welcome to the club. Very cool story. Glad you've joined us. Hope you'll post some pics eventually, and keep us posted on movement into class A. What a cool objective using a 39A instead of some souped up bolt gun.

Alde, I lived in Olympia for a while, and occasionally made it up between Hood Canal and the Olympics. I mostly walked into the edge of the Buckhorn Wilderness from the east side, up the side of Buckhorn Peak over (east rim of) the headwaters of the Dungeness River. Spectacularly beautiful and rugged country.

Mo, thanks for posting those photos. Made me a little envious of you, dude. It's just been soo freakin' long since I've had the time to do that sort of thing. That grouse must know that s/he is living on borrowed time. I'll bet it would fly if it saw you without the 39, but knows it won't stand a chance with you and it if it comes out of hiding.
__________________
______________

Blades, Levers, Sticks & Wheels
Nematocyst is offline  
Old October 10, 2009, 12:25 AM   #2395
teetertotter
Member
 
 
Join Date: October 8, 2009
Location: Janesville, WI
Posts: 188
I selected an all round rifle even though I don't hunt. I'm partial to lever action as always wanted one. Yes, very few will use a 39A, but I have read that there are a feww people that are AAA and still use their 39a. I enjoy the sport and that is what counts. I can claim mid this past summer at state shoot, took 3rd in B class. We had shoot out for tied second place and I lost. Great experience. Nice thing though, we have 2 AAA shooters, and they have given me pointers and 1 one of them has been my mentor. I might try bench rest with my 39, just for fun next year. Local gunsmith keeps asking me when am I going to join them on Saturday mornings. 6X is max at 50yds. I will have to ask for 6.5X approval and see what they say. At my age, they will probably allow handicap! Plus, when they see my 39a, they will chuckle as I would pose no threat. Buuuuut, some might be surprised! lol
teetertotter is offline  
Old October 10, 2009, 02:47 AM   #2396
Kivaari
Member
 
 
Join Date: November 17, 2005
Location: McKinney TX
Posts: 25
39A

Here's my recently acquired '77 39A among friends.

__________________
Kivaari

quality SKS trigger tuning...over 1,000 done one at a time

www.kivaari.com

NRA Endowment Member
Life Member Texas State Rifle Assoc
Kivaari is offline  
Old October 10, 2009, 09:54 AM   #2397
teetertotter
Member
 
 
Join Date: October 8, 2009
Location: Janesville, WI
Posts: 188
I clean my barrel with Hoppes snake with a little 9 on it. After about 300 rounds, due to the micro groves, I want to keep relatively clean. It takes about 15 rounds after cleaning to bring back the accuracy. My thought is with build up in the grooving, there is loss of accuracy. Any thoughts on my thought? I am a weekly steel Silhouette competitor going through 300-500 rds. Comments welcome with 39a target usage experience.
teetertotter is offline  
Old October 10, 2009, 08:40 PM   #2398
dfariswheel
Member
 
 
Join Date: December 26, 2002
Posts: 5,986
Depending on the ammunition, most .22's are more or less "self cleaning".
By this I mean that the rifle seldom looses accuracy from any fouling, because the bullets tend to clean out any fouling left by the previous round.
Cleaning the bore actually may cause damage to the barrel from cleaning gear wear.

Most Match .22 shooters usually only clean the bore at the end of the season, before storing the rifle, and that's mostly to prevent the bore from rusting.
I've seen .22's that would lead up from some cheap .22 ammo, but firing good grade plated ammo would actually clean the bore out.

My advice is to not clean the bore unless you're not going to be firing the rifle for a while and you live in a damp area.
I usually wipe the lube out of my 1950 Marlin 39-A in the spring, shoot it through late fall, then clean and lube for winter storage.
However, I watch things due to the damp area I live in.
dfariswheel is offline  
Old October 10, 2009, 10:06 PM   #2399
teetertotter
Member
 
 
Join Date: October 8, 2009
Location: Janesville, WI
Posts: 188
Thank you Farisw...I assume this would be even when switiching ammo brands to try out? Also, if I shoot 2 days a weeks or 300 rds a week for 330days a year, forget any barrel cleaning? Or 4000 rds in that time frame, then clean or when accuracy is being lost? More thoughts please.
teetertotter is offline  
Old October 11, 2009, 02:49 AM   #2400
Nematocyst
Member
 
 
Join Date: August 5, 2005
Location: Downeast Maine
Posts: 11,648
Kivaari, them's real purty rifles.

If you were going to tune a 39A trigger,
what would you set the pull at?

Do you work on 39s (and other levers), too, or just SKS?
__________________
______________

Blades, Levers, Sticks & Wheels
Nematocyst is offline  
Reply


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:40 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
vBulletin Optimisation by vB Optimise.
This site, its contents, Shooting Reviews, and its contents are Copyright (c) 2010-2013 Firearms Forum, Inc.
IMPORTANT DISCLAIMER
Although The High Road has attempted to provide accurate information on the forum, The High Road assumes no responsibility for the accuracy of the information. All information is provided "as is" with all faults without warranty of any kind, either express or implied. Neither The High Road nor any of its directors, members, managers, employees, agents, vendors, or suppliers will be liable for any direct, indirect, general, bodily injury, compensatory, special, punitive, consequential, or incidental damages including, without limitation, lost profits or revenues, costs of replacement goods, loss or damage to data arising out of the use or inability to use this forum or any services associated with this forum, or damages from the use of or reliance on the information present on this forum, even if you have been advised of the possibility of such damages.