Quantcast
Post 1911 Trigger Job Problems - THR
THR  

Go Back   THR > Ammunition, Gear, and Firearm Help > Gunsmithing and Repairs

Welcome to THR
You are currently viewing our site as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have, access to post topics, communicate privately with other members (PM), respond to polls, and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!


If you have any problems with the registration process or your account login, please visit the help section.

Reply
 
Thread Tools
Old June 4, 2014, 12:42 PM   #1
chiltech500
Member
 
 
Join Date: November 18, 2013
Location: N of Allentown PA
Posts: 352
Post 1911 Trigger Job Problems

I had 2.5 lb trigger job on a Springfield Armory 9mm to use for Bullseye use. My intent was to use it as the base for a 22 Nelson conversion.

I had some issues with the gunsmith in getting my pistol back to me and don't want to name names, but I will doubt anything he says to me at this point, which is why I am asking for info. here.

I have shot the pistol in 9mm about 200 rounds, a few times after inserting a mag the slide snapped closed. I know the smith replaced a very stiff stock SA mainspring with a much lighter main spring.

I also have experienced what I believe are light firing pin strikes. The round doesn't fire and after exam there's a slight pin mark; then I have re-chambered the round and it fires. So I'm believing the smith used a lighter firing pin spring.

I believe he replaced the recoil spring with a lighter spring as well, ejected cases go almost nowhere (that's the sign of a light recoil spring right?)

Any opinions, thoughts ideas are welcomed.
chiltech500 is offline  
Old June 4, 2014, 03:14 PM   #2
BBBBill
Member
 
 
Join Date: March 7, 2005
Location: Florida
Posts: 1,278
Slide closing on magazine insertion is usually due to the slide stop not being fully engaged with the slide stop notch in the slide. If the stop lug is not fully seated in the notch, the shock/vibration from seating the mag can cause it to slip out. If the angle on the back of the slide stop and/or the notch are incorrect, they can cam apart from the force of the recoil spring pressure. Both problems together almost guarantee it to happen.

Lighter mainspring won't cause that the slide to slam closed. It was probably changed if/when the SA ILS mainspring safety was eliminated. The safety uses a much stronger, shorter spring that is held captive by the lock, actuated by the spanner key shipped with the gun. I'm betting he eliminated that and converted it to standard 1911 parts.

Light firing pin strikes are not caused by a light firing pin spring. The FP spring resists the movement of the firing pin forward, so a lighter spring would provide less resistance. He probably left the titanium firing pin in.... or put in the wrong pin. It is a non standard 1911 part with little mass to transfer energy from the hammer (and mainspring). Better to replace it with a steel pin made for the SA sized firing pin hole if you wish to continue to shoot it in 9mm. Firing pin sizes are specific to caliber and manufacturer, so be specific when you order.

A lighter recoil spring will throw brass further, not dribble it out at your feet.

A proper trigger job starts with quality parts of the correct dimensions. Briefly (and incompletely) the hammer hook surfaces are stoned to a smooth finish without removing too much material. The hooks are cut down to .020" (never shorter than .018").The sear nose is stoned to the correct angle, polished, and a relief cut made on the back. From there it is mostly tweaking the two left legs of the sear spring. The mainspring can change trigger pull a bit and some do that, but it is not usually replaced just for trigger pull improvement. Only after all other fitting steps are done and usually for other reasons than trigger pull. The only reason yours would have been changed is to eliminate that abomination of a safety lock. Is your thumb safety is fit correctly? Is there any movement of the sear when you pull the trigger with the thumb safety engaged?


A really great 1911 smith who can straighten out you problem is about 3 hours from you -
Innovative Custom Guns, LLC
162 Moudy Drive
New Enterprise, PA 16664
email – jim@innovativecustomguns.com
phone – 814.766.3004

Last edited by BBBBill; June 5, 2014 at 10:36 AM. Reason: clarity, spelling, & syntax
BBBBill is offline  
Old June 5, 2014, 07:42 AM   #3
chiltech500
Member
 
 
Join Date: November 18, 2013
Location: N of Allentown PA
Posts: 352
Quote:
Lighter mainspring won't cause that the slide to slam closed. It was probably changed if/when the SA mainspring safety was eliminated. The safety uses a much stronger, shorter spring that is held captive by the lock, actuated by the spanner key shipped with the gun. I'm betting he eliminated that and converted it to standard 1911 parts.
He did return parts which I did not study carefully, among one of which looked like the back strap of the SA. I know the original mainspring was heavy, it was the most difficult hammer to pull back I have ever used.

I can't imagine why there would have been changes to the slide stop notch(?) or recoil spring.

I will have to try (pulling the trigger) with the thumb safety engaged? Is that what you mean?

I will send you a PM with the name of the gunsmith.

Thanks
chiltech500 is offline  
Old June 5, 2014, 09:33 AM   #4
Jim Watson
Member
 
 
Join Date: December 24, 2002
Posts: 17,956
The slide "auto closing" is not likely connected to a change in mainspring, unless something really weird like friction between the hammer and the bottom slide rail is acting.
There are a LOT of pistols that will close the slide when a magazine is vigorously inserted. It comes from spring balance and the engagement angles of the slide stop lever and notch.
MY Springfield 9mm will, as will many many Glocks and S&Ws. We just consider it a time saver in IDPA competition. It is not likely to occur when you install your Nelson.

Misfires are probably from too light a mainspring in combination with the titanium firing pin and its stiff spring. You need either a stronger mainspring or an Ed Brown steel firing pin and regular Wolff XP firing pin spring... or both. I have not had a misfire from a 19lb mainspring (23 is GI, SA ILS is about 28) although 17 was not enough for Wolf primers in one of my guns. You may need a stronger mainspring for the Nelson .22 upper, rimfires are harder to ignite.

Mr Milks at Innovative was the house gunsmith at EGW before going into business for himself. He has a good reputation.
__________________
I have a few facts and a lot of opinions.
Jim Watson is offline  
Old June 5, 2014, 10:45 AM   #5
BBBBill
Member
 
 
Join Date: March 7, 2005
Location: Florida
Posts: 1,278
I'm thinking that the main issue is the firing pin and it's spring. Check to see if it is the factory titanium pin and heavy spring. Easy fix.
Identify the parts returned. That will help. As Jim said, many will auto close upon insertion of the magazine. The magazine itself can sometimes be the culprit. Recoil spring changes are sometimes necessary when changing mainsprings, especially the SA ILS mainspring. There is a range of workable spring rates, depending on the loads and individual gun. After all of the mods to the gun are complete, then you match the spring to the load. The slide stop may have been on the ragged edge and is just now manifesting the issue. Yes. Pull the trigger with the safety engaged. Look down into the gun in front of the hammer where the sear and hammer engage to see any movement of the sear.
BBBBill is offline  
Old June 5, 2014, 12:53 PM   #6
chiltech500
Member
 
 
Join Date: November 18, 2013
Location: N of Allentown PA
Posts: 352
Thanks for all the help.

The misfires were with 9mm as I have not used the frame with the Nelson conversion yet.

I will do the sear test and will take a close look at the parts returned. If I'm uncertain about which firing pin was returned I will take a photo and post it.

Quote:
A lighter recoil spring will throw brass further, not dribble it out at your feet.
I'm shooting 3.4g Titegroup with a MBC 125 LSWC. Ballistics average 1050 fps from the SA.

Bill I bought a range of Wolf springs for 1911, I believe 11 or 12# thru 16.5#. Is it possible I need a lighter recoil spring yet - what would the negative impact be from having too light a recoil spring?
chiltech500 is offline  
Old June 5, 2014, 02:12 PM   #7
BBBBill
Member
 
 
Join Date: March 7, 2005
Location: Florida
Posts: 1,278
The spring must be strong enough to strip a round from the magazine and feed it reliably into the chamber. Lighter (or too light), the muzzle will flip up more in recoil, your brass will go into the next county. Heavier (or too heavy), the brass will fall at your feet, the muzzle will dip as the slide closes, and/or the gun might short stroke and fail to eject/feed. Shooters tune their gun within a range of workable recoil springs to suit their load, the way the gun is set up, and individual preferences for the feel of the gun depending on whether they're shooting bullseye, IPSC, etc.

How experienced are you at reloading? Any chance you primers were not seated well? Have you tried factory ammo in it yet?
BBBBill is offline  
Old June 5, 2014, 03:03 PM   #8
chiltech500
Member
 
 
Join Date: November 18, 2013
Location: N of Allentown PA
Posts: 352
I've probably reloaded over 8k rounds by now. I have encountered instances wherein I felt primers were "forced in" when using the firm CCI SPP's. There is a possibility that those 2 (I think it was 2) non-fires were where the primer looked a bit high. When reinserted both rounds that I can think of fired the 2nd go round. I believe both had a slight dimple from the first attempt to fire.

I'm wondering if the recoil spring is still too strong, with cases falling at my feet as you put it. I may experiment a bit. I will also have to see if these problems continue before jumping to conclusions.

The gun is for Bullseye use not one of the action sports.
chiltech500 is offline  
Old June 6, 2014, 07:56 PM   #9
chiltech500
Member
 
 
Join Date: November 18, 2013
Location: N of Allentown PA
Posts: 352
What is this 1911 part? It was one of the items removed during the trigger job on my Springfield Armory 9mm 1911.

[IMG][/IMG]
chiltech500 is offline  
Old June 6, 2014, 08:05 PM   #10
rcmodel
member
 
 
Join Date: September 17, 2007
Location: Eastern KS
Posts: 48,037
Mainspring retainer.
It goes on the bottom of the mainspring and presses down into the notch in the mainspring housing pin to keep it in place in the frame.

See part 5b page 27 of the owners manual.
http://people.cs.clemson.edu/~westal...field_1911.pdf

If he left it out, you are losing mainspring power, and there is nothing keeping the mainspring housing pin from slipping out of the frame.

rc
rcmodel is offline  
Old June 6, 2014, 09:51 PM   #11
BBBBill
Member
 
 
Join Date: March 7, 2005
Location: Florida
Posts: 1,278
Sounds like you need to strip the gun down and check for a missing part. Seems like you're new to 1911s. Have you learned to do that yet? If not, it is easy.
BBBBill is offline  
Old June 7, 2014, 06:09 AM   #12
chiltech500
Member
 
 
Join Date: November 18, 2013
Location: N of Allentown PA
Posts: 352
Thanks gentlemen.

I am new to 1911's and frankly have been leery of stripping the gun down alone. Fortunately an experienced 1911'er member of this forum lives half an hour away and offered to take apart with me.

The gunsmith said he replaced parts. He returned a mainspring housing, 2 springs (firing pin and mainspring I guess) the mainspring retainer and one more part I will post a pic of. Perhaps he used customized parts???

For one, I can't imagine why he would use a different mainspring housing? BBBBill you received my PM with info on who the gunsmith is?
chiltech500 is offline  
Old June 7, 2014, 01:47 PM   #13
Jim Watson
Member
 
 
Join Date: December 24, 2002
Posts: 17,956
He used a different mainspring housing to eliminate the Springfield ILS key lock mainspring housing which has non-1911 internals. Was the odd part an L shaped rod only 3/4 or an inch on each leg?
__________________
I have a few facts and a lot of opinions.
Jim Watson is offline  
Old June 7, 2014, 04:03 PM   #14
chiltech500
Member
 
 
Join Date: November 18, 2013
Location: N of Allentown PA
Posts: 352
Not that I noticed Jim.

The Smith did verify he re-used the titanium firing pin. I have ordered the Ed Brown 9mm firing pin from Brownells and have a kind member who will help me tear down and I will learn.
chiltech500 is offline  
Old June 11, 2014, 01:52 AM   #15
Coldfinger
Member
 
 
Join Date: March 5, 2011
Location: Oklahoma, Texas, Washington
Posts: 78
The smith obviously did not check his work for safety and function following work witch is part of our creed. Based on that alone I would say he is hot garbage. Secondly never take another firearm to him.
__________________
Gunsmith, A.S Firearms Technology Degree, Armorer certified, reloading enthusiast, US Army Active, NRA
Coldfinger is offline  
Old June 14, 2014, 08:13 AM   #16
JDGray
Member
 
 
Join Date: September 16, 2005
Location: SW MI.
Posts: 4,779
Did you have this issue before the work was done?(slide dropping on mag insert)
This can be done with most guns, and I like it!
The SA ILS system uses a short stiff hammer spring, so all the guts in the MSH should be changed when going to the longer, softer, Colt set-up.
JDGray is online now  
Old June 20, 2014, 08:09 PM   #17
log man
Member
 
 
Join Date: January 3, 2008
Posts: 149
Quote:
Originally Posted by chiltech500 View Post
Not that I noticed Jim.

The Smith did verify he re-used the titanium firing pin. I have ordered the Ed Brown 9mm firing pin from Brownells and have a kind member who will help me tear down and I will learn.
Be aware that Springfield uses a proprietary size firing pin in all calibers, half way between the standard 9mm and 45acp. In the Ed Brown line the correct FP for an SA is the #826. The smaller 9mm pin will most likely allow what's called primer flow, and brass chips will clog up the firing pin. This is more of a problem with the higher pressure 9mm cartridge over a low pressure 45acp. So one problem will be corrected, and a new one started, if the wrong pin is used, it does make a difference.

LOG

Last edited by log man; June 20, 2014 at 10:07 PM.
log man is offline  
Old June 20, 2014, 09:01 PM   #18
BBBBill
Member
 
 
Join Date: March 7, 2005
Location: Florida
Posts: 1,278
chilltech, sorry I lost track of this thread. I haven't been on here much due to lots of other stuff getting in the way. Yes, got your PM. The smith is known to me. I believe that he is very knowledgeable and stands behind his work. Have you contacted him to discuss? If not, please do. No smith wants to leave a bad taste with a customer. The titanium pin will be OK with a standard firing pin spring, but not with the extra power spring that SA factory installed when using a conventional mainspring of normal strength. So it was not inappropriate to leave it in place.
BBBBill is offline  
Old June 20, 2014, 11:03 PM   #19
Chuck Warner
Member
 
 
Join Date: November 13, 2008
Location: Rio Rancho N.M.
Posts: 166
Hmm.

Chilltech, sorry to hear of your frustration.

The mainspring housing was replaced with a standard bar stock unit, along with a 20lb mainspring. You also have a standard power firing pin spring with the factory Ti pin. This is a standard combination we use with the optimized hammer and TR sear.
Your hooks are cut at .020 thou. This is a standard combo here for a 2.5 lb trigger job. Never seen a misfire with factory ammo, but there can always be a first. I didn't have a steel pin in stock or available at the time to replace yours, or I might have suggested it. When you contacted me about the pin, I think we covered that.
As for having a problem getting it back, when you sent the gun in, I warned you about time frames due to our move, and I accepted the work on that caveat, and you were fine with that.
A phone call would not have hurt either, as a follow up to the steel pin question, something I recommended then as well.
We finished the move, and are back to reasonable turnaround on smaller jobs.
Your recoil spring was not changed, and without further info, it's hard to dial you in with the gun. Familiarity does help.
The parts you received back were the stock internals and those I replaced with new. You seemed quite ecstatic with the gun when you got it back, and the only thing I got was a question regarding the pin.
Any decent gunsmith can address your other issues, and as always, I'm only a call away.
Cold finger, hot garbage? Really? I assume by "witch (which?) is part of our creed" that you are a gunsmith. In being so, if that's the case, a lesson you might learn is not to jump too quick with out all the facts.
We test with 50 rnds of factory ammo. There might be the slight possibility it could be ammo related as well.....
Either way, it shouldn't be too hard to get to the heart of the matter with someone more familiar with the gun taking a peek.

Best,
CW
Chuck Warner is offline  
Old June 23, 2014, 12:12 PM   #20
chiltech500
Member
 
 
Join Date: November 18, 2013
Location: N of Allentown PA
Posts: 352
Chuck, I did not mean to have your name brought up in a public forum.

The pistol is fine really, the slide closing sometimes when inserting a mag forcibly is due to SA's cut on the lock stop - I don't usually slam in mags so it's not really an issue.

The primary reason for the trigger job was to use the frame for a Nelson Conversion 22 for Bullseye and I have had ZERO problems in that regard, so the titanium firing pin and that other stuff isn't really important in the bigger picture of things.

Then looking at the misfires, I use my handloads, and as I said the gun functions flawlessly with the Nelson Conversion. The 9mm was shot out of convenience but for whatever reason, the gun is not accurate - and it wasn't in 9mm before the trigger job.

So I am not terribly inconvenienced in any way - if I had been I would have called you Chuck. Do you recall I called and asked about the titanium firing pin? It's no problem, I ordered the "9mm" firing pin from Brownells and will install with some help. Besides, it will be good for me to watch and learn because I haven't toyed with any 1911 internals out of being careful not to mess things up.
chiltech500 is offline  
Old June 23, 2014, 12:14 PM   #21
chiltech500
Member
 
 
Join Date: November 18, 2013
Location: N of Allentown PA
Posts: 352
Log Man, the Ed Brown firing pin I received is the 825 for: "9mm, 38 Super and 10mm" per the packaging.
chiltech500 is offline  
Old June 23, 2014, 12:44 PM   #22
log man
Member
 
 
Join Date: January 3, 2008
Posts: 149
Quote:
Originally Posted by chiltech500 View Post
Log Man, the Ed Brown firing pin I received is the 825 for: "9mm, 38 Super and 10mm" per the packaging.
This is a very common mistake by inexperienced SA users, not having yet realized that SA uses the same proprietary size pin for both 45acp and 9mm, and everything in between. This standard #825 Ed Brown size 9mm pin will seem to work, as it is small enough to pass through the firing pin hole, and ignite the primer. However it is too small, and will allow the primer metal to bulge back into the excess space, and as the case is pulled down during recoil, particles of the bulged area will be sheared off. Might seem okay at first, but will result in failure eventually, especially when used in a high pressure cartridge.

The Ed Brown #826 is the correct size. Measure the tip diameter of the Ti pin in your pistol.

LOG
log man is offline  
Old June 23, 2014, 06:44 PM   #23
Chuck Warner
Member
 
 
Join Date: November 13, 2008
Location: Rio Rancho N.M.
Posts: 166
Chilltech,
I know you didn't, but as the last guy known to touch your gun, I'm always concerned when a problem develops. I hope the new pin cures that for you.
I try and be available to all of my customers on technical issues, related or not, to any work I do.

Let us know how that works out.

Best,

CW
Chuck Warner is offline  
Reply


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:40 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
vBulletin Optimisation by vB Optimise.
This site, its contents, Shooting Reviews, and its contents are Copyright (c) 2010-2013 Firearms Forum, Inc.
IMPORTANT DISCLAIMER
Although The High Road has attempted to provide accurate information on the forum, The High Road assumes no responsibility for the accuracy of the information. All information is provided "as is" with all faults without warranty of any kind, either express or implied. Neither The High Road nor any of its directors, members, managers, employees, agents, vendors, or suppliers will be liable for any direct, indirect, general, bodily injury, compensatory, special, punitive, consequential, or incidental damages including, without limitation, lost profits or revenues, costs of replacement goods, loss or damage to data arising out of the use or inability to use this forum or any services associated with this forum, or damages from the use of or reliance on the information present on this forum, even if you have been advised of the possibility of such damages.