Quantcast
AR pistol build - THR
THR  

Go Back   THR > Tools and Technologies > Handguns: Autoloaders

Welcome to THR
You are currently viewing our site as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have, access to post topics, communicate privately with other members (PM), respond to polls, and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!


If you have any problems with the registration process or your account login, please visit the help section.

Reply
 
Thread Tools
Old July 6, 2014, 10:21 PM   #1
Balliet
Member
 
 
Join Date: November 29, 2013
Location: the sticks
Posts: 36
AR pistol build

im building a pistol. i have the stripped 'virgin' lower, stripped upper, sig brace, lpg with pistol grip, and phase 5 pbt. i would really like input on upg components, and barrel suggestions. does anyone make a bull barrel (for weight out front)?

thanks in advance
Balliet
__________________
"no one loves you like you do"
Balliet is offline  
Old July 6, 2014, 10:23 PM   #2
Balliet
Member
 
 
Join Date: November 29, 2013
Location: the sticks
Posts: 36
oh yeah, its for home defense. and its gonna be in 5.56.
__________________
"no one loves you like you do"
Balliet is offline  
Old July 7, 2014, 05:22 AM   #3
dogmush
Member
 
 
Join Date: May 7, 2008
Location: Tampa
Posts: 519
I haven't seen a bull barrel, but it's the AR world, so I'm sure someone makes it. I also haven't needed any extra weight on my 10.5" pistol.

Are you buying it built or building?

Buying complete: BCM, PSA. Both solid, both with good reps. PSA will be a little cheaper, BCM will have better components. Both will work.

Building: that's a deeper question. I yet a YHM slimline handguard, mils per upper I already had, sourced the small stuff (forward assist, delta ring) from midway, and the barrel and BCG from MAS defense. I had no issues with my stuff. But the sky is the limit with AR parts.

I would recommend carbine gas system, and no less then 10" barrel. Also I know you have the receiver extension, but KAK makes one for the sig brace that let's you run a carbine buffer and spring. Helps with reliability.

Last edited by dogmush; July 7, 2014 at 05:28 AM.
dogmush is offline  
Old July 7, 2014, 07:12 AM   #4
jigglyjames29
Member
 
 
Join Date: January 9, 2006
Posts: 151
I'd go BCM KMR with 11.5" barrel

If you want something functional with pretty much guaranteed quality, but a preassembled upper from BCM or DD.

If you just want a project gun, build it yourself.

You won't save much, if any, money by building it yourself with parts of similar quality.
jigglyjames29 is offline  
Old July 11, 2014, 05:24 AM   #5
justice06rr
Member
 
 
Join Date: October 7, 2011
Location: Florida
Posts: 1,291
For the barrel, I highly suggest at minimum a 10.5" with the carbine gas port. This will ensure the best cycling while still having a short profile. There are plenty of options on barrels out there, so pick a length that suits your needs. You can go shorter of course, but you may run into some cycling issues depending on the config.

Buy a good BCG from Rainier, Spikes, or BCM etc.

Good luck with your build.
justice06rr is offline  
Old July 13, 2014, 11:55 PM   #6
gazpacho
Member
 
 
Join Date: May 28, 2004
Posts: 1,014
PWS Pistol Buffer Tube
__________________
I respect an individual's right not to protect their own self interests, but don't expect me to stand with the sheep while wolves still hide in the grass.
gazpacho is offline  
Old July 15, 2014, 09:56 AM   #7
Big Shrek
Member
 
 
Join Date: March 16, 2014
Location: Florida Panhandle
Posts: 174
Get the best trigger kit you can find.
__________________
A firearm should be a tool in the hands of a deadly weapon, not a deadly weapon in the hands of a tool.
Big Shrek is offline  
Old July 15, 2014, 10:47 AM   #8
Balliet
Member
 
 
Join Date: November 29, 2013
Location: the sticks
Posts: 36
I appreciate all the input guys I'm nearly there all that's left is barrel length and the gas system to go with it leaning towards the 10 and a half given the replies I've gotten hopefully some pics to follow thanks again
__________________
"no one loves you like you do"
Balliet is offline  
Old July 15, 2014, 11:01 AM   #9
MistWolf
Member
 
 
Join Date: August 17, 2005
Posts: 1,429
Do a bit of searching to find a good deal on a 10.6 or 11.5 inch barrel. The carbine gas system work well with both barrel lengths. Using the Syrac Gen II gas block will allow you to tune the pistol to run reliably and with softer recoil.

The Magpul MOE is a good handguard for the AR pistol as it's simple to install, rugged and very economical. Or the B5 handguard which is slimmer. Free float handguards are nice but cost more and are not necessary. Spend the money towards an Aimpoint instead
__________________
"The basic tool for the manipulation of reality is the manipulation of words. If you can control the meaning of words, you can control the people who must use the words" -Phillip K. Dick
MistWolf is offline  
Old July 15, 2014, 01:35 PM   #10
32_d3gr33s
Member
 
 
Join Date: March 17, 2013
Location: West Michigan
Posts: 239
ive got a 7" barrel on mine and have had about a thousand rounds through it with almost no issues... The only issue i did have was the gas block wasnt tightened enough so the gas tube became misaligned. Caused a few jams until i figured it out. Just go with quality components and you wont be disappointed.
__________________
I Shoot First, Its better to give than to receive...
I could write something cliché and insightful, but that would be too cliché and insightful.
**Anthony**
32_d3gr33s is offline  
Old July 15, 2014, 05:04 PM   #11
Fishbed77
Member
 
 
Join Date: November 23, 2010
Posts: 2,243
I picked up a 10.5" Melonite-finished barrel from Aero Precision, and I have been extremely pleased. I was able to nab it on sale for under $200. In the last few weeks, I've run about 600-700 rounds through it with no issues.

http://aeroprecisionusa.com/barrels/...taper-pin.html

They make a version without the FSB as well:

http://aeroprecisionusa.com/barrels/...05-barrel.html

So far, it has been flawless on my 10.5" SB-15-equipped pistol build (with the excellent KAK buffer tube that uses the carbine castle nut). With an H2 buffer, it shoots softly and cycles everything from cheap Russian steel-cased .223 to M193 and M855 to heavier match ammo. It is also proving to be just as accurate as my 16" carbine.

I can also say that the Melonite/blackening finish (Aero Precision call it QPQ) is TOUGH, and it resisted my best efforts to mar the barrel when hammering on the FSB and installing the barrel.

Much has been made of the benefits of an 11.5" versus a 10.5" barrel, but I have yet to see them in practice. As stated, this rifle has performed flawlessly, and 10.5" barrels have served well on the Mk18 CQBRs for years now.


.

Last edited by Fishbed77; July 15, 2014 at 05:17 PM.
Fishbed77 is offline  
Old July 16, 2014, 08:21 PM   #12
justice06rr
Member
 
 
Join Date: October 7, 2011
Location: Florida
Posts: 1,291
I use Free-float handguards because they are easier to install and add a bit more accuracy depending on your setup. They're not necessarily expensive, depending on where you buy. You can buy them for under $100 at many places including ebay.

Here's another good vendor of AR15 parts. They have freefloat handguards in varying lengths with free shipping:
http://www.ar15depot.com/handguards.htm

If you're on a budget, they have a 7.5" pistol barrel for $125shipped.

Here is another Vendor of AR15 parts (SOTA) that has a 8" pistol barrel for $90.
http://sotaarms.com/component/jshopp...ew/13?start=12



I built a 10.5" AR pistol with a carbine gas system with the SB15 in FDE. The 10" handguard gives it the same sight radius as a midlength rifle although it is a much shorter AR.


For camparison, here it is with a 16" AR before I installed the SigBrace.
justice06rr is offline  
Old July 17, 2014, 10:06 AM   #13
rodinal220
Member
 
 
Join Date: July 9, 2005
Location: USA
Posts: 1,008
BCM 11.5" and a DD 10.5" barrel


Buffer tube: http://www.kakindustry.com/

barreled upper:http://www.bravocompanyusa.com/

H2 buffer(BCM)
Bolt carrier assembley(BCM)
LPK(assorted Colt,LWS)
Charging handle(BCM GF small)
Springs: either ISMI or Wolff
rodinal220 is offline  
Old July 17, 2014, 12:05 PM   #14
wally
Member
 
 
Join Date: January 2, 2004
Location: Houston, Tx
Posts: 10,444
Quote:
I use Free-float handguards because they are easier to install and add a bit more accuracy depending on your setup.
I agree, will usually let you get a longer sight radius with your BUIS too.

You probably don't want to go below 10.5" with 5.56 as it'll be hard to find a suppressor rated for it down the road.

Justice06rr's photo with the SB-15 is pretty much my opinion of the sweat spot for such.
__________________
Your commitment to Freedom and Liberty is measured by your tolerance for others doing things you disapprove. NRA Endowment Member, 2007.
NRA Patron Member, 2009. NRA Benefactor Member 2012. There is no "race" or "ethnicity" section on the NRA membership application, unlike the Federal 4473 form to purchase a firearm!
wally is offline  
Old July 18, 2014, 07:01 AM   #15
Simmy952
Member
 
 
Join Date: May 11, 2009
Posts: 72
I just got finished putting one together. My goal was a budget friendly AR build. The parts used were a Anderson stripped lower, PSA MOE lower parts kit, and a Androcorp AR 10.5 upper. Like stated above, I would not go below a 10.5 barrel but if you want to go shorter that is your choice. There are many out there to choose from.

http://custombuiltarms.com/ar-uppers...ol-uppers.html
http://androcorpind.com/product-cate...pers/556-nato/
http://shop.redxarms.com/UPPER-ASSEMBLIES_c3.htm

These were just a few that I looked at. The only reason I went with the Andro upper was the cost. I was able to purchase the railed model 10.5 complete with BCG and handle for $450 shipped.

Good luck with your build and have fun.
Simmy952 is offline  
Old July 21, 2014, 10:20 PM   #16
HKGuns
Member
 
 
Join Date: August 29, 2004
Location: Bora Bora
Posts: 2,006
Buy a 10.3" DD MK18 upper and call it good.




100 yards, Iron sights, first trip to the range. (I can barely see the target at 100 yards using irons.) Shots on the right are me walking the irons into the black.

Zero malf's of any kind in several range trips since this target was shot.


Last edited by HKGuns; July 21, 2014 at 10:27 PM.
HKGuns is offline  
Reply


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:35 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
vBulletin Optimisation by vB Optimise.
This site, its contents, Shooting Reviews, and its contents are Copyright (c) 2010-2013 Firearms Forum, Inc.
IMPORTANT DISCLAIMER
Although The High Road has attempted to provide accurate information on the forum, The High Road assumes no responsibility for the accuracy of the information. All information is provided "as is" with all faults without warranty of any kind, either express or implied. Neither The High Road nor any of its directors, members, managers, employees, agents, vendors, or suppliers will be liable for any direct, indirect, general, bodily injury, compensatory, special, punitive, consequential, or incidental damages including, without limitation, lost profits or revenues, costs of replacement goods, loss or damage to data arising out of the use or inability to use this forum or any services associated with this forum, or damages from the use of or reliance on the information present on this forum, even if you have been advised of the possibility of such damages.