Quantcast
Mauser Broomhandle - THR
THR  

Go Back   THR > Tools and Technologies > Handguns: Autoloaders

Welcome to THR
You are currently viewing our site as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have, access to post topics, communicate privately with other members (PM), respond to polls, and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!


If you have any problems with the registration process or your account login, please visit the help section.

Reply
 
Thread Tools
Old July 17, 2014, 01:11 PM   #1
MacBean
Member
 
 
Join Date: July 16, 2014
Location: Maine
Posts: 13
Mauser Broomhandle

I picked up a Mauser Broomhandle and need help to figure out exactly what it is. I have done some research and am still a little puzzled. So here goes........
It has matching serial numbers....447636. Tangent rear sight with graduations to 1000 meters. "NS" new safety. 3.9 " barrel. " Waffenfabrik Mauser Oberndorf A Neckar" on the right side. "Waffenfabrik mauser oberndorf / N " on top of the barrel. Under the barrel looks like a 4 over a B Y. At the end of the barrel "763 Germany" and import mark " CAI ST ALB VI ". " U" with a crown over it on end of the bolt. 22 grove walnut grips with Red 9. This is a 9mm. "U" with a crown over it under the ser. # by the barrel. The only other mark I see is a circle with three lines in it above the right grip. Can anyone help me? It would be appreciated. Thanks.
MacBean is offline  
Old July 17, 2014, 10:23 PM   #2
MacBean
Member
 
 
Join Date: July 16, 2014
Location: Maine
Posts: 13
Does anyone have any info on this broomhandle ?? Thanks.
MacBean is offline  
Old July 18, 2014, 12:06 AM   #3
N003k
Member
 
 
Join Date: November 21, 2008
Location: Connecticut
Posts: 670
Quick googled turned up this:
Quote:
Postwar Bolo

This was the first major variant out of the Mauser factory after the war. Production started in the early 1920s, perhaps 1922.

Due to the terms of the Treaty of Versailles, German pistols were limited to 100 mm barrels or shorter, and calibers under 9mm. Mauser satisfied these restrictions by reviving an older variant, popularly known as the Bolo. Although often called the "small-frame" Mauser, most of the frame is identical to that of the full-size guns. The grip is notably smaller, but all the internal parts are identical to those of the larger pistols. The original Bolo may have been an attempt to make the gun slightly less bulky overall, a notion supported by the fact that nearly all of the very early six-shot guns were Bolos - that is, they had the smaller Bolo grips and the short (100 mm, or 3.9 inch) Bolo barrels. See more on this subject here. However, the postwar Bolos all have 10 shot magazines.

The Postwar Bolo is identical to the Wartime Commercial, with these exceptions -
3.9" barrel with the front sight on a barrel band
No proof stamp on locking block
Small grip
22 groove walnut grip panels
Barrel serial number and proof stamps change places - serial number is now on side of chamber, proof stamp is on diagonal flat above it
Lanyard ring swivels from side to side, rather than fore & aft

The Bolo dominated postwar production throughout the 1920s. It retained the WAFFENFABRIK MAUSER markings, even though the factory name changed to MAUSER-WERKE A.G. in the early 1920s. System Mauser gives an observed serial range of 444476 to 793350 for Postwar Bolos. My own database lists Postwar Bolos from 440864 to 674447.

Around serial 500,000, a Mauser banner mark was added to the left side of the Bolo frame.
Got it from: http://askmisterscience.com/1896mauserbackup/index.html

As for the Red 9 grips it also makes note under the original ones that "During the last twenty years or so, significant numbers of guns with shot-out bores have been bored out to 9 mm and are now wearing reproduction Red 9 grips. This by itself is not a problem, but it causes confusion with genuine 1916 Contract guns."

Hope that helps!
N003k is offline  
Old July 18, 2014, 11:58 PM   #4
9 fingers
Member
 
 
Join Date: March 4, 2012
Posts: 80
I suggest you try the Mauser forum, link attached.
9 fingers
http://www.mauserguns.com/forum/index.php?board=2.0
9 fingers is offline  
Old July 20, 2014, 08:08 PM   #5
MacBean
Member
 
 
Join Date: July 16, 2014
Location: Maine
Posts: 13
Thanks for the help. I will check out the links.
MacBean is offline  
Old July 21, 2014, 12:19 AM   #6
HisSoldier
Member
 
 
Join Date: September 26, 2007
Posts: 1,016
I've always wanted one of those, sort of like an MG TC, things sticking out all over like they weren't sure how a handgun should look.

One thing that scares me about them is an apparent propensity for worn out rifling, evidently the rifling was shallow from the factory perhaps? Or maybe it was the corrosive ammo of the old days? Plus of course the barrels can't be easily swapped out.

Alas the days when I could save up for and buy such a delightful anachronism are long gone for me, one in the condition I'd want would cost over $1500.
__________________
Sig P-238 stainless trigger installation video; http://www.youtube.com/watch?v=Jh2v_-87DRM
HisSoldier is offline  
Old July 21, 2014, 01:03 AM   #7
Willie Sutton
Member
 
 
Join Date: April 28, 2013
Posts: 1,559
Century Arms import, likely from China.


Willie

.
Willie Sutton is offline  
Old July 21, 2014, 09:26 AM   #8
wlewisiii
Member
 
 
Join Date: January 1, 2010
Location: Hayward, WI
Posts: 1,566
Had a post-war Bolo in 7.63 a couple of years ago. Interesting firearm, neat design in many ways as the only screw in it was to hold the stocks on.

I had it refurbished, barrel relined and refinished and it still could not hit the broad side of a barn from inside the barn. Further reading indicated that it probably never would without an attached stock which I couldn't afford.

I sold it for what I had into it and put the funds into a camera lens and a S&W 625 in .45 Colt that I have enjoyed much more than the Mauser.

IF you want a beautiful and pleasant to shoot Mauser pistol, search for a HSc instead. Those are exquisite.
__________________
"You better watch out, what you wish for
It better be worth it, so much to die for."
Hole
wlewisiii is offline  
Old July 21, 2014, 10:25 PM   #9
Jim K
Member
 
 
Join Date: December 31, 2002
Posts: 15,206
The import marking is Century Arms Inc., St. Albans, Vermont. When the gun was imported, it was 7.63 caliber and was altered to 9mm later. It is not a "genuine" Red 9. The crown/U is the original German proof mark. The circle with lines may be a Chinese mark.

Most of the guns that came in from China (only a few were made there - most were made in Germany) had really bad bores, which is why they were rebored and re-rifled to 9mm. I don't know the Chinese word for "tomorrow" but apparently that is when they cleaned their guns; with corrosive primed ammo, the result is as expected.

A few had the barrels actually replaced, with the original barrel cut to a stub and the new barrel inserted and soldered in place.

Jim
Jim K is offline  
Old July 27, 2014, 09:47 PM   #10
MacBean
Member
 
 
Join Date: July 16, 2014
Location: Maine
Posts: 13
WOW !

Thanks again.
MacBean is offline  
Reply


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:19 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
vBulletin Optimisation by vB Optimise.
This site, its contents, Shooting Reviews, and its contents are Copyright (c) 2010-2013 Firearms Forum, Inc.
IMPORTANT DISCLAIMER
Although The High Road has attempted to provide accurate information on the forum, The High Road assumes no responsibility for the accuracy of the information. All information is provided "as is" with all faults without warranty of any kind, either express or implied. Neither The High Road nor any of its directors, members, managers, employees, agents, vendors, or suppliers will be liable for any direct, indirect, general, bodily injury, compensatory, special, punitive, consequential, or incidental damages including, without limitation, lost profits or revenues, costs of replacement goods, loss or damage to data arising out of the use or inability to use this forum or any services associated with this forum, or damages from the use of or reliance on the information present on this forum, even if you have been advised of the possibility of such damages.