Quantcast
parallax adj help - THR
THR  

Go Back   THR > Ammunition, Gear, and Firearm Help > Gunsmithing and Repairs

Welcome to THR
You are currently viewing our site as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have, access to post topics, communicate privately with other members (PM), respond to polls, and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!


If you have any problems with the registration process or your account login, please visit the help section.

Reply
 
Thread Tools
Old August 4, 2014, 11:29 AM   #1
tcr1146
Member
 
 
Join Date: March 20, 2014
Posts: 8
parallax adj help

Can someone give a quick review on parallax adjustment on a 3x9 adj objective rifle scope. I bought a used V9 in excellent condition this spring for use on 22s. When I shot today, I could not get the parallax out, at 30 yards. It did not seem to matter what power. In fact, I found it odd that I could not even get the cross hairs well defined until I set the obj on 100 yards instead of 30! Or, is this V9 not a very good scope? It is all steel and made in El Paso I believe and approx. vintage of 70s! Anyway, any suggestions besides using for a hammer? Thanks, Tom
tcr1146 is offline  
Old August 4, 2014, 01:13 PM   #2
rcmodel
Contributing Member
 
 
Join Date: September 17, 2007
Location: Eastern KS
Posts: 49,147
Try setting the AO on infinity.

Then pull up and look through the scope at the blue sky.
If the x-hairs are out of focus, adjust the eye-piece in or out, then look at the sky again.

Keep doing it until the x-hairs are clear & sharp.

Do Not try to adjust the eye-piece while staring through the scope.
Your eye will try to compensate for the out of focus scope much faster then you can screw the eye-piece in & out.

Once the eye-piece focus is set for your vision, the AO distance settings 'should' also be right.

But maybe not.
The old V-9 was an one of the early variables.
And they didn't quite have it all figured out back then.

rc
__________________
Don't put all your eggs in one basket.
Or all your primers in a glass jar!
rcmodel is offline  
Old August 4, 2014, 06:46 PM   #3
tcr1146
Member
 
 
Join Date: March 20, 2014
Posts: 8
Thank you sir! I will try again tomorrow. Tom
tcr1146 is offline  
Old August 8, 2014, 02:40 PM   #4
velocette
Member
 
 
Join Date: January 21, 2008
Location: Ft. Lauderdale Fla
Posts: 641
TCR
Your scope should have an adjustment for Parallax, an adjustment for magnification and an adjustment for reticle focus. The Parallax/focus adjustment is the one with distances marked on it, a ring at the objective end of the scope or a dial on the side of the scope. Magnification is obvious.
Reticle focus is the rearmost adjustment on the eyepiece and secured with a locking ring. It is adjusted by holding the rifle up at a light sky and QUICKLY look through the scope at the reticle. (DO NOT continue looking as your eye will automatically compensate for the reticle focus) Do this quickly and for very short periods of time, adjusting the eyepiece until the reticle is focused when you look quickly Then lock it in place with the lock ring.
Then mount your scoped rifle on a good rest. Find a verticle post or pole or any clear verticle item at 100 yards. Align your scopes verticle crosshairs with the verticle post. Then carefully, without touching or moving the rifle move your eye back & forth behind the eyepiece, watching the crosshairs on the post.
When Parallax is dialed out, the crosshairs will not move as you move your eye back & forth. You can adjust the Parallax ring or dial until the reticle does not move as you move. Then at that distance, Parallax is adjusted correctly. Parallax settings WILL be different at longer or shorter ranges.
I usually use a little dot of white out to mark the correct position of the focus / parallax ring or dial.
NOTE! you may not be at the marked distance when you have dialed out the parallax. Only two of my scopes actually coincide with distance and parallax free settings.
__________________
Breath control + Sight Picture + Trigger control = Gun control
http://www.hrpclub.info/
NRA Smallbore Prone Master
velocette is offline  
Reply


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:03 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
vBulletin Optimisation by vB Optimise.
This site, its contents, Shooting Reviews, and its contents are Copyright (c) 2010-2013 Firearms Forum, Inc.
IMPORTANT DISCLAIMER
Although The High Road has attempted to provide accurate information on the forum, The High Road assumes no responsibility for the accuracy of the information. All information is provided "as is" with all faults without warranty of any kind, either express or implied. Neither The High Road nor any of its directors, members, managers, employees, agents, vendors, or suppliers will be liable for any direct, indirect, general, bodily injury, compensatory, special, punitive, consequential, or incidental damages including, without limitation, lost profits or revenues, costs of replacement goods, loss or damage to data arising out of the use or inability to use this forum or any services associated with this forum, or damages from the use of or reliance on the information present on this forum, even if you have been advised of the possibility of such damages.