|Welcome to THR|
|You are currently viewing our site as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have, access to post topics, communicate privately with other members (PM), respond to polls, and access many other special features. Registration is fast, simple and absolutely free so please, join our community today! |
If you have any problems with the registration process or your account login, please visit the help section.
|August 10, 2014, 07:38 PM||#1|
Join Date: April 1, 2011
Putting an Old Remington 40X Back into Service
Hereís another one from the 1950ís and at least three evolutions of our junior small-bore program thatís not useable. It wonít clean the targets anymore off the bench and the non-original, shop-fabricated stock has a comb height so low the youngsters have to use their chins to see through the sights. It also wears a tiny Redfield front sight difficult to see through for which we no longer have inserts. What I like about it is the turned-down and fluted barrel done in a home shop. While itís not pretty, and not something I recommend doing, it does result in a rifle that comes in under 10 pounds and balances at the receiver ring. With some work the rifle is still capable of shooting, and I have a waiting list of youngsters ready to move out of the kiddie-rifles (Annie Achievers). Iíll also add an Annie front sight and an adjustable buttplate while Iím at it.
The main reason it doesnít shoot any more isnít the barrel (We have a half dozen Remington target barrels made in 1943 that will still clean the targets), itís the 6-dollar piece of wood on a 600-dollar rifle. Unstable, plantation-grown beech with 4 rings per inch that has moved seasonally over the decades beyond the ability of its original glass-bedding job to prevent it from twisting sufficiently to impinge on the action. So the first job is pillar bedding.
The challenge is the top of the barrel channel isnít flat, so I have no built-in index to drill plumb holes for the pillars. So rather than spend time building a one-time jig, Iíll do the best I can and will solve any resulting problems using epoxy in a separate stage. Numrich has replacement stocks for these at 45 bucks, but the originals were hardly ideal for 14-year-old position shooters either and rehabbing this one will cost fewer shop hours.
Normally I donít bed any of the barrel, but this one is so close to the action diameter I make an exception, and insure the recoil block is clear of the stock on its sides and bottom.
As I suspected, alignment isnít perfect, so I adjust the clamps to achieve a perfectly-centered front bedding stud with the rear bedding stud touching the rear of the pillar. After curing, I ream the rear pillar, and rebed the trigger guard in epoxy to achieve a perfectly-plumb bearing for the rear action screw.
I freehand drill the holes for my 10-dollar, shop-made comb hardware, and again solve any alignment problems using a combination of oversize holes and epoxy. The dowel centers are used to locate the blind holes in the cheek piece, and the scoring and sawcuts are to aid bonding steel hardware to epoxy.
After fitting the Annie buttplate and front sight, the result is functional if not pretty. The rifle came in a slightly over 9 pounds and balances at the front of the receiver ring where I want it. Looking at how much comb adjustment is required to achieve a firm stockweld with my large face, Iím surprised the youngsters could use this rifle at all.
And the rifle no longer has any trouble cleaning the 50 and hundred-yard targets using irons, any vertical stringing having more to do with age and infirmity than the rifle.
|Although The High Road has attempted to provide accurate information on the forum, The High Road assumes no responsibility for the accuracy of the information. All information is provided "as is" with all faults without warranty of any kind, either express or implied. Neither The High Road nor any of its directors, members, managers, employees, agents, vendors, or suppliers will be liable for any direct, indirect, general, bodily injury, compensatory, special, punitive, consequential, or incidental damages including, without limitation, lost profits or revenues, costs of replacement goods, loss or damage to data arising out of the use or inability to use this forum or any services associated with this forum, or damages from the use of or reliance on the information present on this forum, even if you have been advised of the possibility of such damages.|