Got my CZ Bobwhite G2 20ga today! Pic Heavy Review.

I asked about this shotgun a bit ago and don't see much information about these online so I'll do a quick first day (unshot) review of the gun and update when I get to shoot it.

I ordered the gun online so I had to pick it up and see it for the first time. The wood was good but as I put it together it was SUPER tight and most all edges were sharp and though it all looked nice it also looked Turkish (the hand engraving all over the receiver I could do without). The finish was very dull and felt a bit sticky all over. I felt a bit of tinge in my stomach that it was a bit too Turkish (I have a dirt cheap Iver Johnson single shot that is a decent gun after a lot of work but very rough)

So I get home and start degreasing the shotgun and going over it. After a lot of rubbing and RemOil the finish is A VERY NICE deep black. I'm very pleased with the black chrome, it's perfectly even and though they could have polished the steel better in a couple spots it is very well done where it counts. A lot of black comes off on a rag (as on most imported guns) and once cleaned up the whole gun looks and feels way better. Even the engraving looks nicer once cleaned out.

The rib is very nicely serrated, the barrels are flared for the choke tubes and the gun comes with all 5 chokes. The bead is a nice white insert and the checkering appears laser cut and well done.

The action is getting a bit easier after some grease and openings. The triggers are really nice, and the wood metal fit is near perfect. For the price I'm extremely happy. It'll have to shoot well of course but so far so good.

Actual weight: 6 lbs 7 ozs
Front trigger: 5.5 pounds
Rear trigger: 6 pounds
Fit is VERY SIMILAR to a Remington 870. My eye is right there on the mount just like an 870. I believe the LOP and DAC are the same with the DAH being 1/4" lower on the CZ than the 870.

Now for a few pics. Sorry for the quality but it's 18° out and getting dark.

@Fine Figure of a Man

The stock does appear to have cast (not sure if that's the right term) for a right-handed shooter.

I'm hoping to get out this weekend for some very informal shooting. I'm headed out for snowshoe hare next weekend and would love to pattern the gun a bit before hunting.

WestKentucky said:

It’s a beauty. I just have 1 question, and it’s maybe a weird question... the wrist on pretty much all double barrels is the weak spot for the stock. Yours seems to have nice wood, but I can’t get a good feel for how heavy that wrist is. Does it feel fragile? Does it feel like the fat end of a baseball bat?

Click to expand...

The wrist is slimmer than a baseball bat fat end but definitely not too slim. It's thicker than my 870. If I had no concern over strength I'd wish it was just a bit slimmer. I have size Large hands.

The more I handle the shotgun the more I appreciate the engraving and the shotgun as a whole. The engraving is all hand done which is impressive no matter the price. It isn't that bad, I just prefer as plain a finish on receivers as possible.

It's burning a hole that I can't get out and shoot this weekend so I spent a bit of time greasing, oiling, and open/closing the action to try to speed it up. It's a MUCH nicer feeling shotgun now. It broke in to a level I can quickly break it open for hunting in about 50 openings. A hundred rounds or so always seems to do the best work to smooth a new gun out, I can't wait!

I've handled this shotgun probably 6 times without getting to fire it once. So I decided to take it apart and sop up some of the factory oil that keeps seeping out of the action.

I carefully filled a screwdriver until I had a perfect straight-sided blade that fit deep into the 2 guard screws. Glad I did because they are tight! The action is held into the stock with a long 12mm bolt under the recoil pad, similar to many pumps.

The action is actually quite awesome. Very well made! I'm a product design engineer and work on mechanisms like this for a living and am impressed with both the design and execution. It's certainly not perfect but the linkages are well done, the hammers and Sears are well hardened and look designed to last, the couple coil springs act on the hammer in an efficient way (the leverage favors speed at the beginning of travel and power at the end). The machining is very well done and frankly I'm shocked at the fit I see for a sub $1000 Turkish gun. Overall I am quite satisfied.

The 12mm butt bolt:


Removing the guard


Right side, both actions relaxed


Left side, both actions relaxed


Left side, left action cocked


View of the bottom of the actions

@earlthegoat2

Extractors. I use a shotgun in Michigan mostly for Partridge and Woodcock. Later in the winter we get out for rabbit a bit (my profile pic is from a few weeks ago). We're going after snowshoe hare in a couple weeks.

I might just take this turkey hunting in the Spring too if it patterns OK.

Got a chance to shoot the Bobwhite finally today! I brought 2 pattern boards and shouldn't have taken my first shots on them as I screwed them both up (wrong distance, wrong hold, etc). Luckily I had some target supplies with me for my handguns and was able to at least check regulation on some 8.5"x11" targets at 25 yards. I'm really pleased with this gun so far! Just plinking around the cabin a bit but it comes up really fast and shoots right to POA for me. The Improved Cylinder choke is really open with lots of holes (I shot 2 patterns with it and both showed holes), but I think I'll keep it in for the snowshoe hare hunt next week. The modified barrel showed almost exactly double the shot density over the Imp Cyl and was a really nice clean pattern.

I'll have to play with other loads to see if I can even out the pattern in the Imp Cyl or else I might go up a step to Modified/Imp Mod.

kudu said:

Get a large piece of paper or cardboard, at least 4' square, preferably 2 of them. Your barrels may not be regulated to the same point of aim. Maybe move up to 20 yards and see where the densest part of your pattern is, that should be your point of impact as opposed to your point of aim. It is also possible for the choke tubes to move the pattern to different points. I had a pretty nice 20 gauge SxS several years ago that I spent close to $3000 for and the left barrel was about 12" low and to the left of point of aim, made clay games a real challenge, really liked the gun but It was sold for a slight loss and I really don't miss it.

Click to expand...

Yeah, I had 2 large sheets for patterning and should have tried out the gun a bit first instead of using them up on my first shots. I held incorrectly (jammed my cheek into the stock like I was shooting a rifle instead of my natural hold) and shot both patterns way low. I shot more to get used to the gun before shooting these little targets and found a much more natural mount put my POI and POA in the same spot. I'll get out soon hopefully with some large craft paper and do some actual patterning.

Had a chance to get out with the Bobwhite over the weekend. What a fantastic gun to carry around!

somethingbenign said:

Thanks for posting such detailed information. Talking me into getting one in 28 for those "I'm out to hike more than hunt" days.

Click to expand...

That's exactly what I got this guy for. There's something inherently different about carrying a straight-grip double. Almost like you're carrying a smooth pole instead of a twisted stick. An 870 can get banned around but the pump forend and pistol grip stock just don't slide through brush nearly as smoothly. Also the balance point on these makes for a perfect place to hold it with one hand in front of the action.

I never had a double barrel before but this weekend I hunted back to a couple place I have seen coyotes and rabbits so I carried #6 in my right barrel with an Imp Mod choke and #4 buckshot in my left barrel with a full choke. It was really cool to be able to do that.