Recent content by pakmcc

I have two of the palmetto uppers in 7.62x39. they are both very accurate. I use .308 and .310 dia bullets of 123 gr. weight with the .310 bullets I can get about 3/4 inch groups at 100 yards(yes, Off a bench rest.) and with the .308 bullets about a inch and a half. I'm using H-4198 and WW 1680...

anyone loading for the 8x56R i'm using 200gr. lead bullets with 18gr. s of 2400, and this works fine. I forgot my load data for the 205 gr. jacketed hornady bullets, anyone??? Pat

SWC for CZ75 I also shoot 160gr. SWC's in my CZ75"D". they are sized for .357 but they work and shoot fine in my 75 "D". and these don't lead up that barrel either. but I do shoot lead round nose my CZ 9mms(115 gr.) and they work just fine. no leading so far. Pat

I use the lee 180 gr. SWC for all my lead bullets on my CZ's(40 S&W) I shoot them in my CZ75B in .40 and I have a CZ tactical sport in .40 cal. These are accurate and do not lead the barrel. I use 5 gr's of WW231 but 4.9 is a little more accurate. Pat

I do garage sales. I pick up any and all kiddies toys. it doesn't matter what age group. It doens't matter what it is. get whatever they have that's cheap. I have a friend with land in the woods. I take the "loot" up there and I supply the guns and ammo and we shoot what ever I bring. "O" my...

Yes, I did know .41 will at lease work in a .44 special. the bullets were going through target sideways. Have you ever tried to resize .41 fired in a .44 chamber back to .41, you need lots of greaze. All my "N" frame smiths have 6 inch barrels so they are hard to tell apart.

well, I pulled the bullets from the LC67 brass and the powder smelled ok, but I dumped it anyway. I reloaded the cases with 46 gr's of IMR 4895(I reloaded some fired LC67 brass the other day and 47 gr.s of IMR 4895 and CCI #34 primers. they worked just fine.) I was able to resize just the necks...

yeaaa, I load for the Hakim but I don't remember what the loads where. I'll try and find them and let you know. I don't hot rod any of my fire arms so any 8mm mauser ammo should be good. get a reloading book and find a good middle of the road loading and try it. and yes, a 180 gr bullet is...

about thirty years ago or so, A gun smith friend found three Smith and Wesson .44 special barrels, in the white, very rough and marked like they're supposed to be. At a gun show. He told me if I found a used model 28 he would make me a .44 special out of the model 28.(note: he had already done...

9mm in .38 speical I've haven't loaded 9mm in .38 special yet, but one of my Lee molds throws a 160gr. SWC in .38 and it works just fine in my CZ's. I do have the round nose 9mm bullet mold in a 6 holer and I can really produce bullets with it. They are suppost to be 124 gr. and mine come out...

well, I pulled a bullet on my LC67 and the powder smelled just like rifle powder, back to plan "C". Pat

I'll have to check and see if I can resize the cases without punching out the primers(depending what brand my reloading dies are)? I don't know if I can get the decaping pin high enough to not decap the brass after resizing the case.(neck). but if the primers are good, then the powder is going...

OK to fire! this is not a trick question, anyone can answer(If you have experience with an M1):banghead: I have some LC 67 ammo, and I'm having problems with it. I think it's getting old. it will not pick up the second round in the clip. if the gun sits long enough to check the spotting...

ok to fire I have some LC 67 ammo, and i'm having problems with it. I think it's getting old. it will not pick up the second round in the clip. if the gun sits long enough to check the spotting scope it want pick up the second round of that try. I reloaded some 30-06 to try in the same M1...

GEt the CZ"D", I have one that will shoot with a CZ champioin(it 9mm also) but I have P-01's and the "D" model, both are great. and accurate. I"ve shot the Ruger and one had a good trigger and the other had crap for a trigger. I carry the CZ 75 "D". To break it in, I"Ve double actioned (dry...