rwilky78's Recent Activity

  1. rwilky78 liked Walkalong's post in the thread What have you done in the reloading room today.

    And hinges on doors. Sucks at rust prevention, but is good for getting light rust off of metal. Our locksmith turned me onto it years ago.

    Jul 6, 2022 at 8:37 PM
  2. rwilky78 liked IALoder's post in the thread What have you done in the reloading room today.

    Sized, trimmed, deburred, and chamfered 20 pcs of 6mm ARC brass to load up to get the scope zeroed after pulling it off to try it on a...

    Jul 6, 2022 at 8:37 PM
  3. rwilky78 liked Ray P's post in the thread What have you done in the reloading room today.

    Since my reloading room is also my gun maintenance room, I can report I cleaned my Savage 110 in 270W, and I replaced the...

    Jul 6, 2022 at 8:37 PM
  4. rwilky78 liked BushMaster-15's post in the thread What have you done in the reloading room today.

    I Don't use it on guns but rather a PTFE spray for lubing My Presses . Don't know about others but I spill small amounts of powder when...

    Jul 6, 2022 at 8:37 PM
  5. rwilky78 liked Walkalong's post in the thread Federal small pistol primers..

    99% of primers failing to ignite is the primer not being seated to the bottom of the primer pocket. Federals are the easiest to ignite,...

    Jul 6, 2022 at 6:51 AM
  6. rwilky78 liked stormshrike's post in the thread What have you done in the reloading room today.

    I will probably start working up a load with w231, 3.9 or 4.0 to start. 4.2 seems to work pretty good for me for any 9mm 124/125grs,...

    Jul 6, 2022 at 6:40 AM
  7. rwilky78 liked stormshrike's post in the thread What have you done in the reloading room today.

    Yep, Lee TL452-230-2R with Eastwood Light Blue. :) [ATTACH]

    IMG_20220604_193052.jpg Jul 6, 2022 at 6:39 AM
  8. rwilky78 liked IALoder's post in the thread What have you done in the reloading room today.

    Primed and loaded 95gr NBT's and IMR 7977 in .243. The epoxy in the seating stem worked great! No marks on the bullets even at the top...

    Jul 6, 2022 at 6:39 AM
  9. rwilky78 liked Reloadron's post in the thread What have you done in the reloading room today.

    Yesterday I finished 100 .38 Special. These were a 4th of July gift to my neighbor who got a nice S&W Model 60 :) Light target loads...

    Jul 5, 2022 at 7:24 PM
  10. rwilky78 liked dbmjr1's post in the thread What have you done in the reloading room today.

    I managed to prime 300 .223/5.56 cartridge cases. Ready to load once I complete load development. Then I pulled 250 Sig Sauer 115gr...

    Jul 5, 2022 at 7:24 PM
  11. rwilky78 liked BushMaster-15's post in the thread What have you done in the reloading room today.

    Motor oil Is that necessary ?. I've Never used motor oil an anything related to reloading ,can't imagine that's good as the cleaning...

    Jul 5, 2022 at 7:24 PM
  12. rwilky78 liked BushMaster-15's post in the thread What have you done in the reloading room today.

    Dings are fixable IMO provided they don't exceed a depth to width ratio ,thus creating a weak point . Gouges are another matter...

    Jul 5, 2022 at 7:24 PM
  13. rwilky78 liked Bearded Phil's post in the thread What have you done in the reloading room today.

    I've had to pull a few 158gr in 357 and 405gr in 45-70 because I forgot to adjust my seater when switching between bullets and from my...

    Jul 5, 2022 at 7:24 PM
  14. rwilky78 liked 270OKIE's post in the thread What have you done in the reloading room today.

    Ha, what's funny is there is a local shop in OKC that for the longest time, the ONLY hollow point ammo they had in stock was a few...

    Jul 5, 2022 at 7:24 PM
  15. rwilky78 liked WeekendReloader's post in the thread What have you done in the reloading room today.

    I have the same LEE mold and I also used Eastwood Mirror Black. LOL Found a nice load using 3.1gn of Clays. Need to work up some loads...

    Jul 5, 2022 at 7:24 PM
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice