Oh look....another 6.5. This time by vortex.

Status
Not open for further replies.
Yawn...but if others are excited that's cool.

IF I were to get into the 6.5 game it would be the PRC. But I'm completely satisfied with the performance I have with the guns in my stable that overlap with many of the 6.5's.

Now a good 6mm for some distance target shooting as well as some yote hunting would be pique my interest, and there are already a lot of good options, just hard to pick one.
 
Watched the reloading video...painfully...with lots of skips forward. This is what happens when you have more money and time than good sense. A pile of new gear and little real world knowledge of how to use it. Sounds like they are taking an abundance of caution into the approach, but for cryin' out loud, start with some boilerplate .223s or .30-06 before diving into a brand new wildcat cartridge!
 
Someone should tell the folks at Vortex, or whoever, that they came too late for the 6.5 Wildcat party. I had this 6.5 Leopard built nearly 20 years ago, when it was being raved about by the 1000 Yd. benchrest crowd. Basically, it's the .3000 WSM necked down to 6.5 but I use .270 WSM brass because its easier to neck down. The wire is attached to a strain gauge over the chamber for measuring pressures. It's a wicked round at 1K. 6.5 LEOPARD3.jpg DSC_1448 (2).JPG DSC_1451.JPG
 
Last edited:
Case volume, max pressure, twist rate etc? I did not see that in the one article I found.
Havent seen anything listed. They may not have actually measures capacity, the videos showed them starting at about 55gr of 4831 and clocking 2700s
Followed by the BMG based, ultra-long action 6.5x99 Nytol to put us all to sleep. :)

Stay safe
Id call that Nodoz......
 
Yeah, the only "problem" with the 264 mag is the twist rate is too slow to adequately take advantage of the higher bc bullets available in 6.5.
The twist rate is not reall a cartridge problem tho, it is a rifle barrel problem. A 1-7.5" .264 Winchester rifle barrel would be a wonderful thing with any 6.5 mm bullet on the horizon.
 
Someone should tell the folks at Vortex, or whoever, that they came too late for the 6.5 Wildcat party. I had this 6.5 Leopard built nearly 20 years ago, when it was being raved about by the 1000 Yd. benchrest crowd. Basically, it's the .3000 WSM necked down to 6.5 but I use .270 WSM brass because its easier to neck down. The wires in pic are attached to a strain gauge used for measuring pressures. It's a wicked round at 1K.View attachment 963094 View attachment 963095 View attachment 963096
Once again WOW just wow !
I remember gluing Oehler (I think) strain gauges on wildcats 15 years ago I gave mine to my son and doubt he uses it anymore . That is one terriffic and ahead of it's time wildcat !.
 
To make it a real winner there needs to be factory rifles chambered in it and a strong (at least initially) supply of factory ammo.

That’s why Hornady can muscle through any cartridge they want. Apparently Ruger and Savage (among others) are properly incentivized build a bunch of rifles and Hornady has an ammo plant......
 
Someone should tell the folks at Vortex, or whoever, that they came too late for the 6.5 Wildcat party. I had this 6.5 Leopard built nearly 20 years ago, when it was being raved about by the 1000 Yd. benchrest crowd. Basically, it's the .3000 WSM necked down to 6.5 but I use .270 WSM brass because its easier to neck down. The wire is attached to a strain gauge over the chamber for measuring pressures. It's a wicked round at 1K.View attachment 963094 View attachment 963095 View attachment 963096



details of that Rifle please!!!
 
details of that Rifle please!!!
Nothing all that special or unusual except the 6.5 Leopard chamber. Built on Rem M-700 action with HS stock and Douglas barrel for testing loads, velocity and pressure. Here it is with similar No. 2 rifle built for actual 1000 yd competitions with 28" Kreiger barrel and Zeiss Diavari-V 6-24X56 scope. DSC_1528.JPG
 
Last edited:
Status
Not open for further replies.
Back
Top