Search results for query: *

  1. PO2Hammer

    PPC Loads for 38 Special and 357 Magnum (Target Level)

    I’ve always had good luck with DEWC’s at 850-900 fps.
  2. PO2Hammer

    9mm subsonic.

    Have you tried it with 9/147? I’ve thought about it, but have always defaulted to Bullseye or 231. Viht does have data for 147 plated, I think Lyman is too conservative to list such a fast powder, don’t see it anywhere else. 2.8 max, that should be pretty darn quiet. Right now I’m using 3.4...
  3. PO2Hammer

    9mm subsonic.

    Where do you find 147 HST’s for handloading? I agree that N310 is awfully fast for 9mm/147.
  4. PO2Hammer

    Single shot 22

    Love my CZ 452 Scout, came with the single shot adapter, but will take mags as well. More accurate than more expensive rifles I’ve owned.
  5. PO2Hammer

    9mm subsonic.

    Would like to get a range report on those 147 match winners.
  6. PO2Hammer

    PPC Loads for 38 Special and 357 Magnum (Target Level)

    Oh yeah, the old timers would remind us that the sprue end should be up.
  7. PO2Hammer

    PPC Loads for 38 Special and 357 Magnum (Target Level)

    I like Unique, or at least I did, 5 grains in magnum brass and I seat cast DEWC to the crimp groove.
  8. PO2Hammer

    What have you done in the reloading room today

    Took the red dot off my carbine, the 9 month accuracy and reliability testing period is over. (1 FT eject, 2 FT fire, exc accuracy with quite a few bullet types) So I loaded another batch of 9mm Luger with Blazer brass, Rem 5-1/2, 4.4 W231 and Sinterfire 100 grain frangible FP’s @ 1.120”.
  9. PO2Hammer

    What have you done in the reloading room today

    Switching back from Power Pistol to W231 for some 147 plinkers for my 9mm carbine. Blazer brass, Rem 5-1/2, 4.3 W231, Rainier 147 plated RNFP @1.125”. Some of the last of my Rainier bullets, they were a darn good bullet.
  10. PO2Hammer

    9mm subsonic.

    From Lucky Gunner
  11. PO2Hammer

    9mm subsonic.

    Do you really think it would be 300 fps slower in a Glock than a 8” AR with 147’s? I don’t think it would be that much. A hot 115 load would loose that much, but all the chrono data I’ve seen of 147 loads is amazingly consistent from 4” to 16”.
  12. PO2Hammer

    Mossberg lever action .30-30: Why discontinued?

    Ruger resurrected the Marlin name and took over the market.
  13. PO2Hammer

    9mm subsonic.

    I think so. I use Bullseye and W231 in pistol and carbine loads with 147’s. Quiet even without a suppressor in the carbine.
  14. PO2Hammer

    Are you "brand loyal"?

    Somewhat. Like everything Redding makes, especially the comp dies and the 10X. For components I like everything Hornady makes, but I’m growing very fond of RMR bullets.
  15. PO2Hammer

    What have you done in the reloading room today

    Fired up the BL 550 for the first time in a while. Loaded 9mm Luger with GFL brass, Rem 5-1/2, 5.0 grains Power Pistol and 124 RMR match winners @ 1.055”.
  16. PO2Hammer

    “New” old Colt 9mm AR

    The mag release cuts might be off, causing low rounds.
  17. PO2Hammer

    “New” old Colt 9mm AR

    If it were me I would be very concerned about that. I agree that you may have a serious issue. Worth a thread of its own.
  18. PO2Hammer

    Front sight taper?

    I bet more knowledgeable folks will be awake in a few hours if you can wait, but I would bet out to the right when viewed from the shooting position.
  19. PO2Hammer

    How to Load LSWC For 9mm

    IMO, HS-6 should be reserved for fire and brimstone loads.
  20. PO2Hammer

    How to Load LSWC For 9mm

    I loaded my coated MBC 125’s to 1.055” and the sweet spot for me was 3.6 grains W231. I would start at 3.2. With a can I would think HS-6 would be louder than W231, more powder, more noise. W231 is also cleaner.
Back
Top