Quantcast

Search Results

Search Again
Page 1 of 78
  1. 45 Dragoon
    Post

    1851 Colt bolt fitting

    On a Pietta, it'll be fine to go with the whole side. De-burr the bolt "window" and you'll be fine. Mike
    Post by: 45 Dragoon, Dec 12, 2019 at 9:12 PM in forum: Blackpowder
  2. 45 Dragoon
    Post

    1851 Colt bolt fitting

    The "high" side is the tall side (you can tell by looking at the factory or the replacement) and that is the side you should take down with 220...
    Post by: 45 Dragoon, Dec 12, 2019 at 7:43 PM in forum: Blackpowder
  3. 45 Dragoon
    Post

    SOOO... many Patersons and SOOO... little money!

    LOL!!! Mike
    Post by: 45 Dragoon, Dec 10, 2019 at 1:54 PM in forum: Blackpowder
  4. 45 Dragoon
    Post

    The RUGER OLD ARMY Club

    Ok, gnats ass or not, if that is the difference then that is the difference. A single action with perfect timing and a perfect length hand won't...
    Post by: 45 Dragoon, Dec 10, 2019 at 8:19 AM in forum: Blackpowder
  5. 45 Dragoon
    Post

    The RUGER OLD ARMY Club

    You're description of what happens is correct. It also tells me that your pawl (hand) is slightly short. The Ruger hole system, instead of a...
    Post by: 45 Dragoon, Dec 10, 2019 at 5:15 AM in forum: Blackpowder
  6. 45 Dragoon
    Post

    genuine Colt 2nd. generation 1862 pocket navy pawn shop score....

    Thanks Dicky!! Mike
    Post by: 45 Dragoon, Dec 9, 2019 at 9:16 PM in forum: Blackpowder
  7. 45 Dragoon
    Post

    The RUGER OLD ARMY Club

    Scuubbs, You can extend the hammer plunger by lengthening the flat cut along its length. Keep in mind, you can only go so far as you will go...
    Post by: 45 Dragoon, Dec 8, 2019 at 2:36 PM in forum: Blackpowder
  8. 45 Dragoon
    Post

    The RUGER OLD ARMY Club

    Yessir! The "foundation" of timing is the "length of the cycle". If you don't start there, you'll keep chasing the elusive " gremlin ". So first...
    Post by: 45 Dragoon, Dec 8, 2019 at 11:38 AM in forum: Blackpowder
  9. 45 Dragoon
    Post

    The RUGER OLD ARMY Club

    PM sent. Mike
    Post by: 45 Dragoon, Dec 7, 2019 in forum: Blackpowder
  10. 45 Dragoon
    Post

    The RUGER OLD ARMY Club

    Ok that is the "bolt". The hand is what rotates the cyl. Ruger calls these parts the "cylinder latch " and "pawl" respectively. The hand or pawl...
    Post by: 45 Dragoon, Dec 7, 2019 in forum: Blackpowder
  11. 45 Dragoon
    Post

    The RUGER OLD ARMY Club

    [ATTACH]
    Post by: 45 Dragoon, Dec 7, 2019 in forum: Blackpowder
  12. 45 Dragoon
    Post

    The RUGER OLD ARMY Club

    [ATTACH] [ATTACH] Scuubbs, the bolt block lays beside the bolt and gives lateral support. This takes the side force at lock-up. Now, the bolt can...
    Post by: 45 Dragoon, Dec 7, 2019 in forum: Blackpowder
  13. 45 Dragoon
    Post

    The RUGER OLD ARMY Club

    You're welcome! Its been mentioned a couple of times now so, as a hint, the cylinder should never be able to move after full cock. That would...
    Post by: 45 Dragoon, Dec 7, 2019 in forum: Blackpowder
  14. 45 Dragoon
    Post

    The RUGER OLD ARMY Club

    Congratulations scuubbs, nice ROA! The half cock notch has a lip (for safety) which means you'd have to pull the hammer back enough to release...
    Post by: 45 Dragoon, Dec 7, 2019 in forum: Blackpowder
  15. 45 Dragoon
    Post

    Part A of the Plan is Complete...,

    Hmmmmm . . . sneaky . . . but I like it!! Sounds like a great plan!! (How'd you keep from smiling the whole time and keep from giving...
    Post by: 45 Dragoon, Dec 4, 2019 in forum: Blackpowder
  16. 45 Dragoon
    Post

    THR Dragoon Club

    Hey Jackrabbit1957, actually, there are 3 of those pins! The 2 you see and one on the rear side of the frame. These are what I call...
    Post by: 45 Dragoon, Dec 2, 2019 in forum: Blackpowder
  17. 45 Dragoon
    Post

    THR Dragoon Club

    Will do sir, will do ! Mike
    Post by: 45 Dragoon, Dec 1, 2019 in forum: Blackpowder
  18. 45 Dragoon
    Post

    THR Dragoon Club

    Hey Hoof! Yap we ran off in tha ditch but all is cool now!! Lol Yep, those were my first ever conversions and they've been my test beds for all...
    Post by: 45 Dragoon, Dec 1, 2019 in forum: Blackpowder
  19. 45 Dragoon
    Post

    THR Dragoon Club

    This is how they started (many years and miles ago!!) [ATTACH]
    Post by: 45 Dragoon, Dec 1, 2019 in forum: Blackpowder
  20. 45 Dragoon
    Post

    THR Dragoon Club

    Hey Painless!! Looks like it fits in perfectly!!! Mike
    Post by: 45 Dragoon, Dec 1, 2019 in forum: Blackpowder
Showing results 1 to 20 of 1,558 Next >
Search Again
Page 1 of 78
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice