Search results for query: *

  1. C

    Help with a stock

    Pass on the arch angel. Get a decent stock like a Manners, McMillan or even a b&c
  2. C

    professional scope mounting, Virginia beach

    Feeler gauge and torque wrench is all that needed
  3. C

    Ballistic Calculator accuracy??

    Taliv is right, u have to make sure all parameters are correct on your end before you can expect correct results.
  4. C

    260 Rem and 6.5 Creedmoor Experiences

    The 6.5saum doesn't rank in the barrel burner category with the 264 and 6.5 nosler. The 6.5wsm was up there really short barrel life, but switching to the saum case significantly lower the pressure of the round increasing barrel life.
  5. C

    260 Rem and 6.5 Creedmoor Experiences

    Easier to find good 6.5cm than 260
  6. C

    Ptac worked over Glock 34

    After rolling in mud and sand at a match like k&m shooting center in FL the stipple is very welcome in keeping a good grip
  7. C

    Ptac worked over Glock 34

    It's mainly for 3gun which doesn't have a power factor, and for the Precision Rifles Series "prs"
  8. C

    Ptac worked over Glock 34

    I don't have an invoice yet, they sponsor my team and done these guns as part of the sponsorship. I'm not keeping anything a secret, I'm just not willing to price other company's work.
  9. C

    Ptac worked over Glock 34

    The slide was lightnen, fulcrum ultimate trigger installed, stippled, kkm barrel, tugston guide rod. Zev heavy insert magwell, warren black rear and fiber front sight. I'm not 100% sure on the cost that would be somthing you would have to get with them to discuss. We went with distress not to...
  10. C

    Ptac worked over Glock 34

    In not worried about what others think, the slide is lightend for comps to lessen the mass of the slide. There is purpose to work not just cosmetics. Look at all the limited guns you see. They all have slide cuts, this gun is significantly lighter than my other long slide glocks. The finished...
  11. C

    Ptac worked over Glock 34

    Precision tactical arms company out of FL has worked over some glocks for me and my teammates, I just want to show you guys the amazing work they are doing. If you guys need anything give Ward and crew a call. This is their distressed finished and signature slide cuts. http://www.ptarms.com
  12. C

    Subsonic .308 loads, suppressed

    take the suppresser off and shoot paper at about 5-10 yards, always check this before shooting with your can on. 8 twist would have been a better for your application.
  13. C

    I want a rifle in 6.5 ... but factory or custom build?

    I would second what all taliv has to say. Custom is the way to go and he has mentioned some great builders.
  14. C

    Savage Hog Hunter vs...

    I bought one to shoot subs out of Supressed since it was a 10twist. The gun itself is fine, the stock is one of the cheapest worse ones made. I'm not a fan d the accutrigger but for just casual shooting it's fine. Accuracy was good tho, I put some 175's @ 1000 with it even with the stock. I...
  15. C

    Favored gun oil?

    50/50 royal purple oil and royal purple atf mix, works amazing. I have used to ton of other things picked up at matches all over the place and so far like this one the best.
  16. C

    Precision Rifle Picture Thread

    Here is a few before they got scoped up.
  17. C

    Rifle scope zeroing question...

    bullets do not rise, they start to fall as soon as they exit the muzzle. You can point the muzzle up and give the illusion that it is rising.
  18. C

    Long range scope recommendations

    Bushnell DMR like taliv said can't be beat for around 1k
  19. C

    Anybody try the new Bushnell optics 1-4x 24 with BDC?

    They are not a bad scope for the money, I think it's biggest downfall is that it is a FFP. While FFP is a must for me with my long guns, I can take or leave it in a 1-4. If the retical is specifically designed for it then it works it not i thinks it's bad on all accounts. I think this scopes...
Back
Top