Search results for query: *

I will try to pick me up a couple of different powders to try and see what works best. I am thinking about WST, N310, Solo 1000. Any others? Mark

Thanks everyone for the info. I will be playing around with it some soon. I am currently loading with Hp-38, I do have some bullseye that isa tad faster burner that the Hp-38. But i may also try some WST out. I believe it is between the Bullseye and the Hp-38 if the chart I have is correct. I...

I bought most of my supplies for manventureoutpost.com they had the best price on the net and didn't rape you on the shipping to make up for it. they also had a good selection of reloading equipment and some supplies. Mark

I am loading 9mm and 45acp right now that I shoot in USPSA and IDPA at home. I want to find out what is the best combination to lower felt recoil to allow quicker shoots for double taps and such. I also plan on changing out my recoil springs to help out with this. Would a lighter bullet with...

Since you did not say if you are useing lead or jacket bullets, or the OAL it is hard to tell. It could be not enough crimp, or to light of a charge. Try working it up from 4g in .2g increments and see if it cleans up. Also check you crimp to be sure it is close to .473-.470. Bullseye is kind of...

I had mine in a MTM box that busted open and cracked the lid. One box down now. Mark

Well I loaded up 10 rounds each from 3.8 -4.4 in .2 g increments. While walking back to the house I droped the box and scattered them all over the ground. Oh well time to start over again. If all is good I will shoot these after, If not I will have to pull them down. Mark

Thanks guys, I will deffinetly start at the lower range and work up. I just wanted to be sure they were not to short to cause high pressures. Mark

Hey I am just starting to load up some 9mm with Berry's 115g FP and Bullseye. I looked up the laod in my manuals and will start with 3.8 and work up to 4.6g of bullseye. I have been trying to set up the OAL and the listed OAL of 1.075 to 1.100 looks long for these bullets. I seated them down to...

I also had the same thing and it ended up being spilt powder under the punch. If it was working right before I would check that out. Mark

Precision Delta is a good source for bullets. Mark

I will also say consider the progressive. I just started out and that is what I got. One thing I think you need to think about is can an do you work with your hand an on machinery? I do at me job. Just be honest with yourself if you can tinker with thing and fix them. Watch all of the videos on...

I use the #45 plate. You can use eaither one, but the #1 will fit looser. Mark

I just did the same thing my self this week. It sure is fun to shoot you first relaods. I just loaded up 100 for my shoot in the morning. Mark

Yes it was a good time. I am ready to make make a 100 or so for our shoot this weekend. Mark

Pics. didn't work I am trying to link them from photobucket. I will try again later. How do you link photos from pohotbucket. thanks, Mark

Well I made my first trip to the range to test my first loads out. Everything went well I still have all of my fingers and my slide did not come off of my gun and hit in between the eyes. All loads were .45ACP 230 FMJ with Bullseye WLP and mixed brass. All groups were off hand 5 shot at 20...

That is what I was thinking. I know my factory rounds eject with no problems. I may shorten them up as you advised earlier. Thanks for all the help.

I did some checking this morning. I pulled the barrel from .45 ACP XD pistol and checked the head spaceing on my first round of bullets. They did head space correctly when I droped them in, but when I loaded a couple in the the mags and tried them the first round would load up fine but it would...

Walkalong thanks for the help. I had it set there and someone said to follow the manual so I reset it back to 1.274. If I have feed problems I well bring it back down to 1.260 I got that load from Lyman's pistol and revolver handbook. It actulley said to start at 3.8 up to 5.3 g of Bullseye...