Search results for query: *

Hi EERW Thank you very much for updating me. I have read about FLGR and about Blade Tech holsters, I will check it again. What is your opinion how it shoots? I have spent 23 years on duty with different type of CZ guns and my last was CZ 75 BD Police. I was able to shot with CZ better then...

I have bought my CZ 75 SP 01 Tactical two days ago I have to wait until Monday I would be able to register gun at the police. Gun looks well balanced. Little bit heavier then my Kimber Custom but it doesn’t mater. I am going to make some changes. Standard sear replaced by hard sear and hammer...

I would like to know which front sight base for Kimber Custom II is right .060 or .075? Novak’s shows all sizes for Kimber Thank you for help BR yoky

If it is possible s don’t sell CZ it is very good gun. Year or Two ago I sold my CZ 75 BD Police and it was my big mistake :banghead: . Now I am waiting for new CZ 75 SP-01 Tactical. It is new gun of this year. It looks like Police pistola P 01 but it is steel gun in full lengths not Compact...

Thank you very much for all advices. I have solved problem and Novak’s just sitting properly. I had to little tuned bottom part of sight and now it seats perfect. Thanks to P500 I was able to move sight off and on. Small diamond file helped me much. I understand that is was cosmetic...

I need help I replaced original Kimber sights by Novak’s sights. I have find out very small free gap between rear sight and seating face of the slide. End of bottom square flat of the sight doesn’t seat fully on flat top of the slide. I don’t know what is wrong. Thank you in advance for...

Hi Max Sorry for my mistakes. In my documents year 1951 is year when SA has adopted 9mm Makarov. Your data are correct. BR yoky

There is some info about Russian war handguns. Russian started to use Nagant which was replaced in the year 1891 very old model Smith and Wesson Russian cal. 44. Nagant was produced in two modifications DA for officers and SA for soldiers. Later SA model was finished and army factory in Tula...

There is link for SB factory and ammo http://www.sellier-bellot.cz/

Hallo everybody here Nice to hear that ammo from my country has good reputation. I have spent my nearly 30 years on duty with SB ammo only. This is official ammo (9mm) for LE, Army and for other Security services in Czech Republic. During my years of service I hadn’t problem with SB...

There is several ways how to move or replace sights. Time ago I have bought P 500 and it works perfect. My Kimber had sights which were sitting in its position very firmly and I was not able to get them out. I have destroyed 3 nylon brasses and no results. Using P500 have helped me a lot. Now...

I have ordered Novak sights. To take down :banghead: Kimber rear is not a problem, I did it. I would like to know how to replace front sight. Is there any step by step instruction and what tool do I need? Thank you for help.

Hi Armoredman Sorry for my inaccurate information and wrong expression According our gun law we can’t use for carry and for personal protection JHP ammo and such a type of ammo. We can’t use ammunition which can cause higher damage to human body. Such ammo is strongly restricted. We can...

Dears I am glad to hear you are satisfied with CZ gun production. I have spent more then 25 years on duty with different type of CZ guns from CZ 52 to CZ 75. I was very satisfied with CZ. Last time I was able to shot P-01 it is good gun but it is not my cup of tee. I prefer 5´´ guns and...

Happy New Year to every body here CCR I don’t agree with your opinion. Nearly whole production of guns from CZUB is covered by powder coatings KOMAXIT. This type of coatings was specially developed for guns by Swiss gun industry for field conditions. I have good experiences with on my...

Plastic hammer Hi photo_guy I have never seen plastic hammers for 1911 gun, but why not. I am not sure if SIG has used such hammer. What I remember my HK USP had hammer which was made from vulcanite. And it worked perfectly. Best regards yoky

Mr Sample I am studying 1911 gun system less then 2 years (yea I know I am beginner) and to rebuild my gun it took 1 year I went with step by step procedure and my first knowledge cam from your and Taady Jacobson¨s knowledge. If I remember on Glocktalk forum it was year or two ago thread named...

Hello Mr. Dave Sample and Mr. Tuner First thank you very much for explanation and help. I try to explain my whole 1911 gun story. Time ago I had to rebuild my Kimber Custom II totally and for this I have changed all internal parts C&S, Thumb safety-Ed Brown, grip safety (Ed Brown)...

Howdy Tuner Thank you very much. As usually your help is highly appreciated. This is not first time you have helped me.. I will do this exactly like you proposed. I thing it is logical procedure. Thanks a lot and best regards Yoky.

I would like to ask you for help. I am gong to replace standard ejector on my Kimber Custom II. I bought Ed Brown extended ejector. There is no problem to replace it. But my question deals with reshaping of the ejectorpart which contacts brass. I have seen this part with different shape from...