Search results for query: *

  1. N

    Remington 870 Magazine Thread Specs

    Keep in mind the tube is induction welded into the reciever if you break it lose your screwed it has to be returned to the factory for repairs .
  2. N

    New shotty....wad plastic and burnt powder lodging between choke and barrel??

    after all you didnt say what kind of a shotgun you were having problems with ???
  3. N

    New shotty....wad plastic and burnt powder lodging between choke and barrel??

    Is it possible you have a remington shotgun and perhaps using the wrong type of choke tube it happens with mossbergs all the time someone screws in a rem choke it looks like it fits but has a gap that freezes the choke tube in place
  4. N

    Finding a year for an 870 without a barrel and not normal side stamps

    it could be the newer 870 i have one it says remington 870 and thats all besides the serial number . you can find the date by the serial number
  5. N

    '92 Win Wood Stain

    You might try birchwood casey walnut stain it has the red that comes close to Winchester Red i just did a model 37 turned out great and it matched the but stock
  6. N

    Troubleshoot Express barrel on Wingmaster

    the end if the barrel isnt cut square trim it up alittle at a time till it fits you can see it in the top picture its bottomed out while the top is held out
  7. N

    armor tuff worth it?

    Wilson does great work Aiptactical does great work too but the remington steel program is tops for restoring an old 870 . The armor tuff coating is like dura coat a bake on finish it wears good and i have not had any complaints
  8. N

    Remington 870 Wingmaster Super Magnum (Rare ?)

    Here in central ohio that gun would bring 450 to 550 with the deer barrel . its a really nice gun but you can find used ones like the matt finish for about 200 used
  9. N

    Best Combat Pump?

    Actualy i have 3 in order the Remington 870 they are solid built like a tank and lots of parts to customize . 2: Mosberg 500 light weight good gun but aluminum wont last as long as steel and im not a fan of some of the barrels being made out of country . last 3: Winchester 1300 Defender with a 7...
  10. N

    Which choke...

    ALso check the underside of the barrel some of the barrels say made in Texas and under the for arm it says made in mexico .Thats why they are so cheap
  11. N

    At-Home Firearm Finishes... what's good in Summer 2018?

    !1: any finish you put on will have to have the old <bluing> removed media blasting is the best way as it gives the new coating a surface to grip onto . 2: if you try the rattle can header paint let us know how it turns out 3: ceracoat is worth the money sometimes you can reduce the cost by...
  12. N

    Mossberg 835 Jamming

    Repace the magazine spring and remove and clean the shell stops . I have a 500 mossberg did the same thing the mag spring does'nt hold the next shell against the stop and it just slides right past tying the gun up .
  13. N

    Remington authorized repair center

    Could i ask is this a matt finish or a polished blue ?? If its a matte finish you might try bill wilson and Wilsoncombat.com . for 229 they clean and refinish your shotgun do any repairs including ejectors replace any worn parts and return it to you with new remington plastic stock and forearm...
  14. N

    Maverick 88 Questions

    To answer your question no you cannot use the 28 inch barrel with a 7 shot tube the 7 shot tube does however have a very rare hard to find vent rib 28 inch barrel as well as a 20 inch cylinder bore <easy to find> barrel the 88 barrels are made in Mexico the 500 barrels are made in U,S,A, and...
  15. N

    Stevens Savage 87D Front Sight Replace

    they just drift out from the left to the right , use a brass drift punch and a hammer tap it out and tap in a new one
  16. N

    Steel cased round stuck in AR-15 chamber

    Take a punch and knock a hole in the side of the case and pry it out if you rip the head off use a stuck shell removal tool and get it out then finish pushing the cleaning rod . Personaly if soaking in oil and doin this didnt work I would take a hack saw and chop it up in pieces and toss it...
  17. N

    h&r singleshot question

    I will look i had a pdf that showed how to take one apart and put them back together . as i recall you have to use a slave pin to hold the trigger group together . ill try and find that pdf
  18. N

    3yelps

    can you cut .010 off the barrel shoulder and set then back the lengthen the chamber the same distance this would alow you to tighten the barrel altitle more. Admititdly i dont know much about take downs in the model 99 or you can take the shim add alittle to the thickness and replace the shim
  19. N

    upgrading my 870

    From what I have read the Remington 870 did not get the military contract because they did not enter the trials, not due to the design of its ejector. Actualy Remington did enter the trials and lost to Mossberg due to failing the drop test Remington 870 stocks broke at the wrist when dropped...
  20. N

    refinish my remington 870 express

    I would think a coat of paste wax on the entire shotgun would be fine .My 870 was cleaned and put away a month ago i just checked it still doin fine in the closet . No rust issues and the wood looks great Johnsons paste wax 60 years and going strong .
Back
Top