Search results for query: *

Received brass in the mail this week! Thanks for throwing them up sir! They will go to good use Sent from my iPhone using Tapatalk

Hi bbq, I've just ordered a sample of MBC bullets for the 380, going to try my hand at loading for it. I could use the brass if no one gives a shout.

This Sent from my iPhone using Tapatalk

Sounds like lipstick on a pig. However I'm not sure what coatings will show, it will depend on the thickness of the product. Cerakote tends to be rather thin as most markings and stampings are still visible. Plating would be pretty thick and parking has a texture that hides imperfections well...

Oh geez I didn't read that last part. I feel like a total goofball lol. Oh well it's all in good conversation. Carry on. Sent from my iPhone using Tapatalk

I have to agree with Mike on this one... The Lee Factory Crimp Die should solve chambering issues due to case bulge from bullet seating. I ran into a similar issue when seating some MBC 180gr RNFP with a 18 brinell rating. When using a bullet that seats that deep, you should take into account...

Thank you Ed for the brass it arrived yesterday. That is the shiniest brass I have ever seen man!!! Take care. Sent from my iPhone using Tapatalk

Thank you Ed. You are da man! Sent from my iPhone using Tapatalk

bds, I would like to throw in for edleit's 40S&W range brass, new 40 needs food. Thanks. Sent from my iPhone using Tapatalk

Just an update in this issue. I did the fix documented in the following link. After shortening the extractor push rod, reliability has been 100% with ball ammo and the few XTP rounds I have tested. I would suggest anyone having the same issues to give it a try. The piece is a few dollars if...

Huge shout out to edleit!! Got package today with a lot more than I expected!! Thanks for the extras! Sent from my iPhone using Tapatalk

Just started reloading 380. Would love to try these out sir! Sent from my iPhone using Tapatalk

More paranoid anti-gun opinions from my local university newspaper. Luckily these are just opinions. It's amazing how an institution of higher learning can instill values of oppressing freedoms. Young minds often corrupted by a majority of liberal professors. This seems to go against the...

Here is an update... a few more presses have been added along with an assembly/armorer bench... IMG_2328 by Justin A, on Flickr IMG_2329 by Justin A, on Flickr IMG_2332 by Justin A, on Flickr IMG_2333 by Justin A, on Flickr IMG_2334 by Justin A, on Flickr IMG_2335 by Justin A, on...

Just wondering. Because I feel that the extractor tension may have a part in this. How would you gauge yours? Can you move it with a finger? Obviously this is subjective and an accurate measure would require specialized tools. However I feel mine is over tensioned causing it to not move out of...

Lol thanks for the advise. However I already have a iwb carry option that I trust. Xds 3.3 I would consider the g42 a similar sized gun intended for iwb carry at best. The Kahr is when I can't carry my xds, I like the option of throwing it in my pocket and forgetting I have it on.

Thanks for your insight, i guess I'll have to try another box or two if something different. That Kahr break in is a bummer. If it needs to go back to the factory, any experience good or bad with that process? Turn around time and success of resolution?

So.. I recently purchased a Kahr CW380 for pocket carry. Before I started carrying I began to put the pistol through the factory recommended 200rd break in period. I have used a variety of ammo from Hornady 90gr XTP, flat nose fmj, round nose fmj.. All have had the same issue. I have gone...

Got the brass today Gummi Bear!!! Thanks for the extra shiny finish. You are da man!

bds, I would like to throw in a Nosler reloading manual (#2). It's an oldie but may be good for a new reloader for a supplement. Good published data. Of course being Nosler it's rifles only.