Search results for query: *

Thanks for the reply's all. I have uniformed the cylinder small end, very little differences.(as I said, timing and lockup were near perfect, Ruger does a very good job with interchangeability) I will try the 148 Gr. hollow base WC. My convertibles are more of a range toy than for any real...

Hi all, just a few questions about the 9mm side of my Blackhawk convertible.. A while back I picked up a 9mm cylinder that dropped in and timed perfectly in my short barrel .357 3 screw Blackhawk. The .357 cylinder is very accurate (well under 2 inches @ 50 yards) however the 9mm is a whole...

Mac66, Actually, Local Gun Range. Sorry about that. Paul

I carry a NAA Mini in 22 MAG, daily, usually in addition to a sub compact .45 ACP. I call it my "everywhere" gun, sometimes I almost forget it"s there. Here in SW Floriduh, we don't wear a lot of clothes, so hiding even a compact .45 can be a challenge some days. The 22 MAG easily lurks in...

I recently ran across one of these at a LGR. Lots of fun to shoot. http://www.youtube.com/watch?v=-RY8Dn8W7EE Mfg. from 1920 to 1934. Please, Tell me everything I don't know about this gem. Looks to me like it might be the perfect ranch/truck gun. Bird shot for dove/pidgeon and slug's...

A long time ago, in a land far away, (OK. late 70's at the Grand American...) I saw and got to shoot a Browning high rib trap gun with a very unusual stock and fore end. It was a red, white and blue, laminated, thumb hole, butt stock with an adjustable comb and a spring driven recoil...

I shot dove and pheasants With a 12 Ga untill my mid 40's, then stepped down to a sweet little BC Moroku in 20 Ga. (yea, lost my hair and my jump shot too) 10 years later, a beer bet had me turning a pair of Savage pump gun barrels into full choke, sub Ga. tubes for the 20. That little o/u...

I have a 922-m,(22 mag) that I bought used, after a time it showed the same symptoms as yours. The problem I found was related to the magazine cut out/safety. (The rifle will not fire without the magazine properly inserted and the blocking lever in the proper position) remove the barreled...

I'm going to be traveling to Gettysburg National Cemetary later this month. ( I was born and raised in Erie, but haven't been in PA. since 1984) I hold a Florida carry permit. I plan to carry conceiled, just as I do every day in FL. I believe Pa. has reciprocity with Fl. how does this effect...

Lathedog, I appreciate the heads up. My Google foo may not be strong enough, but I could not find any info referring to a Rem 600/XP-100 bolt failure, linked to an installed Sako extractor. (Any caliber) Can you (or anybody else) point me to a good source of XP-100 info, that might shed...

I'll be watching with great interest. A few years back, I expended a lot of lead and powder working with the 30 cal/.22 sabots, (from several different manufacturers) in 30 Carbine, 7.62X39, 7.62X25, .308 and 300 Savage. I could make them cycle semi auto's, fly fast and even feed well in...

Thanks Bill. I hadn't heard that about the Sako piece, time to dust off my Google fu. The reason for the push to finish this project is simple. The 7mmBR is going for an extended visit with a friend of mine (out of state) and I've got some hog's around here that need killin' with the X39...

WOW, that's some real purdy stuff. Thanks for the link. I'm gonna wait a bit, to see if somebody has a bolt to trade or some other deal I can't refuse, before I pull the trigger on a fluted, Sako extractor cut, one piece, hi zoot, piece of jewelery. (but that's what I really want, lol)...

I've rebarreled a Rem XP100 to 7.62 X 39 and have been shooting it with the bolt from my 7mm BR. (shoots great, BTW, excellent hog gun) The original bolt was .221 Fireball. I need a bit of help to either find a bolt that will work, (I think 7mm BR might be the only one) A 7mm BR bolt...

RC, The remaining piece on the Judge mike's out at .074-.075". An old Novak I have has a .092"-.093" hole diameter. Neither of these sizes are listed on your link. Any other ideas/sources? Anyone?:banghead: As always, thanks for the reply, Paul. :)

I've got a Taurus Judge, 6 inch. The fiber optic front sight insert is broken, I'm told this is a fairly common occurance. Is the insert rod availible, by itself ? Is this rod a standard size, availible in bulk quantity? I really don't want to send it back to Taurus for replacement...

I recently acquired a slightly used 922-M 22 mag, clip fed. After a thorough cleaning, this old girl will put 5 rounds under an inch at 50 Yds. from a rest. Not terrible, but I think she can do better. The trigger pull is around 7.3 Lbs, gritty, with lots of over travel, and changes as much...

-------------------------------------------------------------------------------- This Riot Shotgun came to me with a "failure to eject" problem. Pictured are the pieces of broken parts I removed. I'm not sure that this is the correct ejector, as all the drawings and pictures I can find...

If I legally hold a SBR, or a suppressor as an individual, CLEO signature, form 1 approved, and I want to, 1) Sell it. 2) Loan it to a friend, to shoot, with out me being present. 3) Gift it to a family member. (same state or another permitting state) 4) Bequeath it, upon my death...

SBR question Posted in error