Search results for query: *

Hey guys, I was looking to put a new stock on my vanguard. I have the old version with the butler creek stock, but I am dropping in a timney trigger. So I ordered a bell and carlson medalist and I have to say I'm disappointed. The inletting looks sloppy and there is aluminum protruding on the...

Hey guys, I have a churchill highlander bolt action rifle chambered in 300 win mag. made by Sabatti. I bought this rifle when I was in high school. I had the stock refinished and added a 26 inch ported barrel to it. Anyway, the stock cracked and I picked up a new, unfinished stock for it. My...

Are manuals any good from the 90s? I have a nosler, hornady and lyman 46th. Thanks. Sent from my iPhone using Tapatalk

Hey guys, I have never had to swag brass before. I only loaded for my hunting rifles and revolvers. Anyway, I am loading 223/5.56 brass. I have a pile of brass that needs swaging. I have a RCBS bench top swager. I read the setup instructions and all that. How do I tell if I have effectively...

Who has the stated primer tool? I just bought one of these tools two or three weeks ago. I am wanting to prime some 223, but I cannot get the small seater plug to tighten. The plug goes so deep, then the tool that came with it cannot grab it anymore to lock it down. I put the large one back in...

Hey guys, I am savaging brass from a makeshift range. I found a pile of 5.56 next to a bunch of 300 ultra mag. All cases have neck cracks and one neck half sheared off. Probably reloaded is my guess. Anyway, it makes me question the 5.56 now. Cases do look staked (primer). Sent from my iPhone...

http://scranton.craigslist.org/spo/3696344009.html This area is so depressed, so I wrote to him to ask if he had any buyers from the area. Also, I asked if he knew when walmart re supplies the ammo shelves. Sent from my iPhone using Tapatalk

I have 223 and 5.56 cases. From the research I have been doing, the jury is out about case differences. I have seen where people have cut the cases in half and both look identical to each other. That said, is there a difference between the two? All my loading manuals have 223 but not 5.56. Can...

I just bought hornady bullets for my AR. I didn't notice untill I got home that they are .223. Can I use these? The box says .223 45 grain hornet. Sent from my iPhone using Tapatalk

Hey guys, I have a back ordered set of AR series dies in 223/5.56. That said, does anyone know who has these in stock? Do I need the AR set or will the standard die work ok. I am loading both 223 and 5.56. The loads are for my stag model 2 in 5.56x45mm. Thanks Sent from my iPhone using Tapatalk

Hey guys, I picked up a RCBS rock chucker press. I just got it installed and I am having an issue. When I try and put a shell holder in, the spring that holds it in place pops out. I have to hold the spring and wiggle the shell holder for it to go in. On my lyman, I just push it in and pull it...

Hey Guys, I have a t-mag press from the 90s. I was resizing 44 mag brass and noticed as I was lowering the case out of the die that the turrent was moving. Basically lowering the ram was pulling the turrent down with it and the rear if the turrent was coming away from the press. I noticed on the...

Hey guys, I don't own a 40, but I have been picking up range brass. I have found some cases that are swollen near the extracting rim on the case. I am assuming its an unsupported chamber like a glock. The primers are smeared like a glock to boot. Anyway, I was wondering if this is caused by...

Hey Guys, I never loaded for my AR before. With the current panic, I decided to do that. Anyway, I have a can of h-335 powder. I do not have any primers, but I did find small rifle magnum primers. Can I use these? Thanks